A boy sits on a mery-go-round so that he is always located a distance r from the center of rotation. The merry-go-round is originally at rest, and then due to rotation the boy's speed is increased at the rate a,. Determine the time needed for his acceleration to become a. m r = 2.4 m m a = 1.2 Given: af = 0.6

A boy sits on a mery-go-round so that he is always located a distance r from the center of rotation. The merry-go-round is originally at rest, and then due to rotation the boy's speed is increased at the rate a,. Determine the time needed for his acceleration to become a. m r = 2.4 m m a = 1.2 Given: af = 0.6

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the acceleration of body B in Fig. P-1056, assuming the pulleys to be weightless and frictionless. Ans. aB = 5.85 ft per sec2
Problem 1.1 Three objects with masses m1 = 36.5 kg, m2 = 19.2 kg, and m3 = 12.5 kg are hanging from ropes that run over pulleys. What is the acceleration of m1?
A crate has a mass of 120kg and the coefficient of static and kinetic frictionis 0.60 and 0.50, respectively. The crate starts from rest and the motor exerts a tensionT= 1220 + 200t (N). If the elevation of the dock is 30 degrees from the horizontal,A. What is the velocity of the crate after 1sec? B. Compute the power transmitted after 1sec. Topic: Impulse and momentum
A motorcycle starts from rest at t=0 and moves along a circular track with a radius of 400 m. The tangential component of its acceleration is at= 2 m/s2. When the magnitude of its total acceleration reaches 5 m/s2, friction can no longer keep the motorcycle on the circular track, and it spins out. Can the motorcycle complete one quarter of a lap of the track before it spins out? Justify your answer with relevant calculations.
Show the complete solution. Put notes on steps. The wooden block (mass m = 0.6165 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle 0 = 45°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block.NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
A hoop of radius 95mm and mass 100g is rotated via a capacitor driven power source with P(t)=1.61e-1.3tW. (since it is a hoop, it is a special case, and r=rG) Assuming the hoop is accelerated from rest, determine the rotational velocity after t=8.5s. [rad.s-1] Determine the rotational speed of the hoop after t=8.5s if the power source acts to roll the particle from rest on a horizontal surface. [rad.s-1]
Consider a 3-meter long pendulum placed on the moon and given an initial angulardisplacement of 0.4 rad and zero initial velocity. Note that gravity on the earth’s moon is ?? = ?/6, where g is the acceleration due to gravity on earth. (C) Calculate the maximum angular velocity of the swinging pendulum (D) Calculate the maximum angular acceleration of the swinging pendulum
The mass of the m_1 block in the figure is 40 kg, and the mass of the m_2 block is 10 kg. There is no friction between the m_1 block and the ground. The friction coefficient between m_2 and m1 is 0.6 and the kinetic friction coefficient is 0.4. A horizontal force of F = 100 N started to pull the m_2 block as shown. In this case, calculate the accelerations of m_1 and m_2 blocks?
A disk rotating with constant acceleration of 0.005 revolutions / s2 And the movement starts from rest. What is the angle velocity after one minute? How many turns makes the same disc in point number one after one minute. If an external force does not affect the body, what does that mean? And if the body is in free fall, is its speed constant or variable, what is its acceleration equal, and how can the friction be reduced between the contact surfaces
Calculate the expected acceleration (Eq. 2) and the experimental acceleration (Eq. 3). This hanging mass will supply the unbalanced (net) force acting on the cart. The track is assumed to be frictionless, so the only force present is that from the hanging mass. m1 (hanging mass), m2 (cart).
A particle, originally at rest and located at point (3 ft, 2 ft, 5 ft), is subjected to an acceleration a={6ti+12t2k}ft/s2 .
Block A in Fig. has mass 4.00 kg, and block B hasmass 12.0 kg. The coefficient of kinetic friction between block Band the horizontal surface is 0.25. (a) What is the mass of block C ifblock B is moving to the right and speeding up with an accelerationof 2.00 m/s2? (b) What is the tension in each cord when block B hasthis acceleration?