A bracket plate is used to transfer the reaction of a beam to a column flange as shown in Fig. Ex. 10.9. The bracket plate is connected to the column flange by a 6 mm fillet weld. Compute the maximum load that can be placed over the bracket plates at a distance of 75 mm from the flange of the column section, IS Coa P 75 mm IX 100 mm T 100 mm 2P O 200 mm I.S.H.B. 300 @576.8 N/m Fig. Ex. 10.9 75 mm

A bracket plate is used to transfer the reaction of a beam to a column flange as shown in Fig. Ex. 10.9. The bracket plate is connected to the column flange by a 6 mm fillet weld. Compute the maximum load that can be placed over the bracket plates at a distance of 75 mm from the flange of the column section, IS Coa P 75 mm IX 100 mm T 100 mm 2P O 200 mm I.S.H.B. 300 @576.8 N/m Fig. Ex. 10.9 75 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel rod is bent to form a mounting bracket. For each of the mounting brackets and loading shown, determine the reactions at A and B. Take L = 230mm, F1 = 6ON, F2 = 130 N, M = 14 N.m *
a) If the bolt exerts a force of 50 lb on the pipe in the direction shown, compute the force (lb): i) that the smooth contacts at A exert on the pipe. ii) that the smooth contacts at B exerts on the pipe. b) Determine the maximum weight of the pipe (lb) that the vise can hold if the magnitude of the forces at A and B are equal. ac = 9 lb
Compute the resultant force acting on the pin at C. a. 22.5 kN b. 42.0 kN c. 48.1 kN d. 35.5 kN choose letter of the answer
Bar weld shown in English, (between AB: 1m / BC: 3m / CD: 2m) a) Show the support reactions and load resultant on the rod? b) Calculate the support reactions? c) Normal Force, Shear Force and Moment bonding calculation by cutting the points you specified? d) Draw the cross section effect diagrams? Specify the maximum positive and negative moment? e) Check the cross-section influence diagrams with a simple method, describe the control steps briefly?
d. Calculate "P" in KN considering failure on shear on rivets Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
1) what is the block shear in plate moment connection in steel members. How the allowable moment capacity of the plate moment connection is calculated based on the limit states of Bock shear (2) How the allowable moment capacity of the Plate moment connection is calculated based on the limit states of(i) Beam Flexure rupture (II) Bolt bearing ( iii) weld rupture (iv) Plate copmression yielding pl explain above by giving sutaible exmple for connecting the webs of two I shaped beams by plates
The box wrench shown is used to tighten the bolt at A. If thewrench does not turn when the load is applied to the handle, determinethe torque or moment applied to the bolt and the force of the wrenchon the bolt.
The bronze C86100 pipe has an outer diameter of 1.5 in. and a thickness of 0.125 in. The coupling on it at C is being tightened using a wrench. If the torque developed at A is 125 lb # in., determine the magnitude F of the coupleforces. The pipe is fixed supported at end B.
Two 10"-15.3 lb channels are welded together as shown in the figure. Find the moment of area of the upper channel about the horizontal centroidal axis Xo of the entire section.
I am ok with parts a) and c) but regarding the part b) I think we should mention the number of loops so the equation should be : SI = ext + int - releases = react. - (3 equ) + (3 equ) ( nb of loops) - releases ( no hinges here )= (4) - (3) + (3)(1) - 0 = 4h degree and if I used the simple method, I brake the frame into 2 membersso r= 2+2+3+3=10 n= 2 membersso r> 3n by 4 degree Does it make sense?
For the riveted bracket shown in the figure below. P = 250 kN. The rivets have diameter of 25mm. The connection can be analyzed by replacing the given load with an equivalent loading composed of a vertical force along acting through the centroid of the rivets and a moment. 1. Which of the following most nearly gives the shearing stress in each rivet due to the vertical force alone acting at the centroid? a. 127.3 MPa b. 145.6 MPa c. 112.8 MPa d. 186.4 MPa 2. Which of the following most nearly gives the shearing stress in rivet D in MPa? a. 134.7 b. 113.9 c. 85.6 d. 156.7 3. Which of the following most nearly gives the stress in rivet B when the instantaneous is 200 mm to the left of cg, in MPa? a. 274.5 b. 341.8 c. 389.6 d. 187.5
An aluminum alloy [E = 10,000 ksi; σY = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi; σY = 45 ksi] pipe at flange B. The pipes are attached to rigid supports at A and C. Pipe (1) has an outside diameter of 2.150 in., a wall thickness of 0.16 in., and a length of L1 = 6 ft. Pipe (2) has an outside diameter of 5.10 in., a wall thickness of 0.19 in., and a length of L2 = 10 ft. If a minimum factor of safety of 1.6 is required for each pipe, determine:(a) the maximum load P that may be applied at flange B.(b) the deflection of flange B at the load determined in part (a). Deflection to the right is positive.