A brass rod (E 110 GPa) with cross sectional area of 250 mm2 is loaded by forces P =15 kN, P2 =10 kN, and P3 = 8 kN. Segment lengths of the bar are a = 2.0 m, b = 0.75 m, and c = 1.2 m. The change in length of the bar is approximately: %3D P2

A brass rod (E 110 GPa) with cross sectional area of 250 mm2 is loaded by forces P =15 kN, P2 =10 kN, and P3 = 8 kN. Segment lengths of the bar are a = 2.0 m, b = 0.75 m, and c = 1.2 m. The change in length of the bar is approximately: %3D P2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.1P: A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel...

See similar textbooks

Related questions

Q: The graph below represents a snapshot at t =0 of a wave of frequency 10 Hz that travels in the posit...

Q: a) Given is a penstock with deflection and subsequent cross-section reduction. Determine the pressur...

A: Find the pressure loss.

Q: 10–9. Determine the moment of inertia of the area about the x axis.

A: Given

Q: Find the degrees of freedom of the kinematic linkages below.

Q: Motion of the sliding block Pin the rotating radial slot is controlled by the power screw as shown. ...

A: Given Data The angular velocity of sliding block is:θ˙=0.13 rad/s The angular acceleration of slidi...

Q: 2. The stresses shown in the figure act at a point in a stressed body. Using the equilibrium equatio...

Q: 10-21. Determine the moment of inertia of the shaded area about the x axis. 10–22. Determine the mom...

A: Find the moment of inertia about x-axis and y- axis.

Q: 2. A 200 kg motoreycle accelerates from 0 to 55 mi /hr in 5.0 s. (a) What is the magnitude of the mo...

Q: A waste heat recovery boiler produces 4.8 Mpa (dry saturated) steam from 104 C feedwater. The boiler...

A: Given Data Steam final state:4.8 MPa,dry saturated Steam initial state:104°C Tai=954°C Tao=343°C ma...

Q: 200 mm 500 mm 250 mm 275 mm 400 mm A,

A: Given m=3.8kgV=1.2m/sF=500NM=25kgrG=300mm=0.3mμ=0.25

Q: A proving ring is 25 cm mean diameter, 4 cm wide and 6 mm thick. The maximum stress permitted is 550...

A: A providing ring has a diameter of 25 cm, a width of 4 cm, and a thickness of 6 cm.The greatest stre...

Q: Determine the required diameter (in inches) of rod AC if the allowable normal stress is 24.95 ksi an...

Q: It is desired to develop a total power 223,800 kW in a hydroelectric plant under a head of 15 m and ...

Q: what is mean of indexing device and what is application of it? how to work what the Mechanism index...

A: In this problem, it is asking the meaning of indexing device along with application and working prin...

Q: A gear has 44 teeth of the 20°, full-depth, involute form and a diametral pitch of 12. Compute the f...

Q: A pair of bullocks exerts a force of 120 N on a plough. The field being ploughed is 16 m long . How ...

A: Given data : Force = F Distance = d To find : Wor...

Q: As shown in the figure, a 300-ft³ tank contains 25 lb of H20 initially at 30 lbf/in². The tank is co...

Q: The INCORRECT statement about the

A: Given; Characteristics of critical point of apure substance;Find incorrect statement ?For the follo...

Q: An elevator weighs 1000 pounds and is supported by a 5/16 inch diameter cable, 1500 feet long. When ...

Q: Time left 0:59:02 Which of the following statement(s) is correct? Oa. Paralleogram Law can be used t...

A: Parallelogram law cannot be used to find Resultant of more than two vectors. It is used to find Resu...

Q: The steel plate has the dimensions shown. Determine the maximum axial force P that can be applied so...

A: Given Maximum allowable stress = 21 ksi r= 0.25 in d = 1 in t = 0.25 in w= 5 in D = 2.52 in To find...

Q: 1. The satellite is moving in an elliptical orbit with an eccentricity e = 0.25. Determine its speed...

Q: A vertical force of 380 N in downward motion accelerates an object with a volume of 0.068m ^ 3 of oi...

Q: The system shown below is released from rest. Determine the acceleration of mass A. (Hint: start by ...

A: Given: mass of the block A→mA=6.5 Kg Let block A has acceleration a in downward direction. And angl...

Q: AT-Shaped beam has a length of L-35 m is acted upon by the distributed load as shown which has a max...

Q: Required information The bolted connection shown in the figure is subjected to a tensile shear load ...

Q: estimate of the enthalpy of evaporation of

A: Given;For water at; T= 250 CdpsdTs=0.189 kPa/Kspecific volume of dry saturated vapour is= 43.38 m3/...

Q: The table shown below describes a 6-bar linkage. Dimension Description 35 mm 2 cm 20 mm Link 1 (0204...

Q: Determine the constraint equation which relates the accelerations of bodies A and B. Assume that the...

Q: T, 1000 K 350 K Heat flow 6k 4k Heat transfer through a composite wall of two sections, each having ...

A: Given, Thermal conductivity of the left wall = k1 = 6k Temperature of the left surface = T1 = 1000 K...

Q: Prepare the user interface elements for a coffee vending machine with following features: Assume a ...

A: A vending machine operates on the fundamentally basic idea of making a payment in exchange for t...

Q: Which of the following will NOT cause a vertical change in the bending moment diagram? Select one: O...

A: Vertical bending moment diagram occurs where there is applied moment. (a) A pin support with an appl...

Q: The system shown below is released from rest. Determine the acceleration of mass A. (Hint: start by ...

Q: Wind direction: a. Assuming that the weather system shown on the North P=1atm map to the right has j...

A: a) et streams are relatively narrow bands of strong wind in the upper levels of the atmosphere. The ...

Q: Derive the first two natural frequencies for a simply supported beam of length ‘?’ and youngs modu...

A: Consider a simply supported beam of length L and mass M at its centre , young's modulus ‘E.

Q: Quiz-ch5 A Carnot heat engine receives heat from a reservoir at 1200°C at a rate of 800 kJ/min and r...

Q: Q6/ Find the natural frequency of vibration for the system shown, when K1 = 10 N/mm, K2 = 5 N/mm, K3...

Q: What is the angle between the force vector and the positive direction of thex-a

A: Correct answer is option a

Q: A wind turbine having an efficiency of 35% and rotor diameter of 33 m is exposed to air flowing at a...

A: Find the power developed by the turbine.

Q: the water temperature in the field

A: Given; Neglecting the heat transfer b/w the water and the ground, the water temperature in the field...

Q: 39. A four-stroke compression ignition engine delivers 600 bhp of brake power output when running at...

A: Answer: The brake mean effective pressure is 120 psi.

Q: Obtain the Miller indices of a plane which intercepts at a, b/2, 3c in a simple Cubic ...

Q: The following data refers to a laboratory experiment with rope break. Diameter of the flywheel = 1 m...

Q: The system shown below is released from rest. Determine the acceleration of mass A. (Hint: start by ...

Q: Create your own 3 unique problems on the First Law of Thermodynamics/Forms of Energy and Equations o...

A: First Law Of Thermodynamics The First Law of Thermodynamics states that heat is a form of energy, an...

Q: what is the value of R1 in kN? what is the value of R2 in kN?

Q: Air occupies a 0.5-m' tank. It starts at a pressure of 5 bar and a temperature of 300 K. Energy flow...

Q: F-150 N Ti 30 - 200 N 35 0.03 m 20 In the xy coordinate system 1.7 points - Calculate the magnitude ...

A: As per bartleby guidelines we are allowed to solve only 1st 3 subparts if multiple subparts are pos...

Q: 3. A piece of wood that measures 3.0 cm by 6.0 cm by 4.0 cm has a mass of 80.0 grams. What is the de...

A: 3. Given: The volume of the piece of wood, V = 3 cm x 6 cm x 4 cm The mass of wood, m = 80 gm

Q: The steel cylinder has a specific weight of 490 (0/f" and acts as a plug for the 1 ft long slot in t...

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

A brass rod (E 110 GPa) with cross sectional area of 250 mm2 is loaded by forces
P1 =15 kN, P2 =10 kN, and P3 = 8 kN. Segment lengths of the bar
are a = 2.0 m, b = 0.75 m, and c = 1.2 m. The change in length of the bar is
approximately:
P
P2
A.
B
Match each item to a choice
Deformation:
Choices:
# 3.4 mm
# 1.6 mm
# 2.1 mm
:0.9 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the ladder itself. Each ladder rail (t5= 4 mm) is supported by a shoe (ts= 5 mm) that is attached to the ladder rail by a bolt of diameter d = 8 mm
A load of F=590 kgf will be hung on a Workshop crane as in the figure. The pole to be used has a diameter of D= 59 mm and a wall thickness of t= 8 mm. Other dimensions are H = 2046 mm, L = 1364 mm. If we take the yield strength of the steel used as cak= 463 MPa, how many times is the system safe when it is calculated according to the point where it is connected to the ground? (Assume no supports shown at the bottom)
A steel bar, the material of which is S355 J2 G3, binds two walls together. Pre-tensioning in tie bar 4.3 kN. The temperature of the rod increases by 15 °C. Calculate the normal stress in the cross section of the bar. L = 600 mm, α = 12μ 1/°C, E = 200 GPa and d = 25 mm . Give the answer in MPa as a whole number as a numerical value only. Correct answer to exercise should be = -27
Given: l1=1,1l ; l2=1,4l ; l3=3l; F1=1,9P; F2=-0,3P; F3 =-2P. Parameter of length l=30cm; cross section proportion: b=1,2h; parameter of loading P=27kN. The rod is made of steel with yielding stress σY=220MPa; factor of safety n=1,6. Find: the height (in mm) of cross section from strength calculation h = ?