A copper rod 6cm in diameter is placed within a steel tube, 8cm external diameter and 6cm internal diameter, of exactly the same length. The two pieces are rigidly fixed together by two transverse pins 20mm in diameter,one at each end passing through both rod and the tube. Calculate the stresses induced in the copper rod, steel tube and the pins if the temperature of the combination is raised by 50°C, take: E,= 210 GPa and a,= 0.0000115 per deg C. E= 105 GPa and a,= 0.000017 per deg C. Calculate the stresses induced in the copper rod. steel tube. Calculate the stresses induced in the pins if the temperature of the combination is raised by 50°C,

A copper rod 6cm in diameter is placed within a steel tube, 8cm external diameter and 6cm internal diameter, of exactly the same length. The two pieces are rigidly fixed together by two transverse pins 20mm in diameter,one at each end passing through both rod and the tube. Calculate the stresses induced in the copper rod, steel tube and the pins if the temperature of the combination is raised by 50°C, take: E,= 210 GPa and a,= 0.0000115 per deg C. E= 105 GPa and a,= 0.000017 per deg C. Calculate the stresses induced in the copper rod. steel tube. Calculate the stresses induced in the pins if the temperature of the combination is raised by 50°C,

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The interval diameter of the hoop formed by the band is 29.98cm. By how much will it be necessary to increase the temperature of the hoop, so that it would slide over the surface of the cylinder? What stress will occur in the hoop when it reaches the same Temperature as the cylinder, if the deformation of the cylinder may be neglected?
A steel band 6mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of the hoop formed by the band is 29.98cm. By how much will it be necessary to increase the temperature of the hoop, so that it would slide over the surface of the cylinder? What stress will occur in the hoop when it reaches the same temperature as the cylinder, if the deformation of the cylinder may be neglected?
A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter . The internal diameter of the hoop formed by the band is 29.98cm . By how much will it be necessary to increase the temperature of the hoop, so that it would slide over the surface of the cylinder ? What stress will occur in the hoop when it reaches the same temperature as the cylinder , if the deformation of the cylinder may be neglected ? (Write complete solution)
An engineering machine component operating in a high temperature environment consists of a copper pipe having a cross-sectional area of 2 000 mm2 and 0.3 m long, which is placed between two rigid caps. Four M22 steel bolts are symmetrically arranged around the tube and parallel to the axis of the tube and are lightly tightened. 3.1 Find the stress in the pipe and the bolts if the temperature of the assembly is increased from 25 0C to 95 0C. 3.2 What load will each bolt carry at the raised temperature? 3.3 Make a neat sketch of the assembly. (ESt = 200 GPa, ECu = 100 GPa, αSt = 12 × 10-6/ oC, αCu = 16 × 10-6/ oC)
A cylinder head of a steam engine is held on by 14 bolts. The effective diameter of the cylinder is 35 cm and the steam pressure is 8.5 kg/cm2. Assuming that the bolts are not initially stressed, find the diameter of each of the bolts if the tensile stress is not to exceed 200 kg/cm2.
A conpound bar is constructed from threa barg 50 mm wida by 10 mm thick fastened together to form a bar 50 mm wide by 30 mm thick. The middle bar is of Alumioum alloy for which E = 70 GN / m ^ 2 and the outside bars are of brass with E = 100 GN / m ^ 2, If the bars are Initially fastened at 18 ° C and the Temperature of the whole assembly is then raised to 50 ° C, determine the stresses set up in the brass and the Aluminum. α (B) = 18 x per ° C and α (Al) = 22 x per "C. (b) What will be tho changes in these stresses if an extemal compressive load of 10 kN is applied to the compound bar at the higher Temperature?
A steel rod of 20 mm diameter passes centrally through a copper tube 40 mm external diameter and 30 mm internal diameter. The tube is closed at each end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projected parts of the rod. If the temperature of the assembly is raised by 60°C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m2 and 100 GN/m2 and α for steel and copper as 12 x 10-6 per °C and 18 x 10-6 per °C.
A copper rod with 0.15 cm diameter is enclosed by a steel tube that has an outside diameter of 0.3 cm and an internal diameter of 0.2 cm. The assembly is fixed at each end. Determine the stresses in the rod and tube if the temperature is at 220oC; at 10oC, there is no longitudinal stress. Based on laboratory results for steel, E = 2.1 x 105 N/mm2, a = 11x10-6/oC, and for copper, E = 1 x 105 N/mm2, a = 18x10-6/oC
A rectangular plate, 30mm by 60 mm is subjected to a tensile force of 5kN in the direction of the plate’s larger side. The plate has a circular hole at the center with diameter of 15mm. If stress concentration factor=2.16, find the thickness of the plate if maximum allowable tensile stress is 80N/mm².
A cylinder head of a steam engine is held on by 14bolts. The effective diameter of the cylinder is 35cm and the steam pressure is 85N/mm².Assuming that the bolts are not initially stressed; find the size of bolts if the tensile stress is not to exceed 20N/mm²
A steel gas bottle 2 m long with a diameter of 250 mm and a 3 mm wall thickness is pressurized to 3 MPa. Determine the stresses. help plz
Find the maximum value of P that will not exceed a stress in steel of 113 MPa, in aluminum of 91 000 KPa, or in bronze of 110 MPa if the aluminum rod is rigidly attached between a steel rod and a bronze rod.