A C250 x 30 American Standard channel beam is supported and loaded as shown here. When z = 1 m and 6 = 10 mm what is the maximum force this beam can support if the stress isnot to exceed 200 MPa?Z8OFLMultiple Choice14.3 kNZ9.83 kN5.12 kN3.86 kN

Answered: Image /qna-images/answer/82e832bc-3614-4c04-832a-a21e48806a9d.jpg

A C250 x 30 American Standard channel beam is supported and loaded as shown here. When z = 1 m and 8 = 10 mm what is the maximum force this beam can support if the stress is not to exceed 200 MPa? Multiple Choice O O O A O 14.3 kN 9.83 kN 5.12 KN 3.86 kN

A C250 x 30 American Standard channel beam is supported and loaded as shown here. When z = 1 m and 8 = 10 mm what is the maximum force this beam can support if the stress is not to exceed 200 MPa? Multiple Choice O O O A O 14.3 kN 9.83 kN 5.12 KN 3.86 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2. Determine the value of Ely at the left end of the overhanging beam shown in the Figure using…

Q: II. The loads on a roof beam consist of a dead load of 0.2 kips/ft, a roof live load of 0.13…

A: Given data, Dead load = 0.2 Kips/ft Roof live load= 0.13 Kips/ft Snow load = 0.14 Kips/ft We…

Q: 5. Determine the horizontal deflection of point C due to the loads with respect to its original…

A: horizontal deflection of point C

Q: 1. Plot the stress-strain diagram of the given data and determine the following mechanica…

A: Given, Gauge length (L) = 50 mm Diameter (D) = 12.5 mm

Q: What are the rules for Gauss-Jordan elimination?

Q: 4- Calculate the fluid acceleration along the nozzle centerline as a function of x and the given…

A: Given, Flow is steady Centerline velocity through nozzle increase parabolically

Q: Using double integration method

A: Given Data E = 70 GPa = 70 × 103 N/mm2 I = 95 × 106 mm4 Determine the maximum deflection in the…

Q: A 3m P Figure 1 6m B 6N 6N 2m 2m Show Transcribed Text Refering to Figure 1, what is the total…

Q: Given the following Mass-Haul Diagram: O $30,000 O $28,000 O $25,375 O $20,250 Net Cumulative…

A: Given:- The mass-haul diagram is given: The limit of free haul = 600 ft The price of excavation =…

Q: what is the specific weight of water?

Q: II. In the given figure, calculate the values of h, and h₂ in cm. 27 cm S₁ = 0.80 h₁ 3 8 cm $₂0.68-…

Q: A vertical photograph of a flat area having an average elevation of 250 metres above mean see level…

Q: Problem 2: Inputs: ● ● w = 300 N/m P = 600 N a = b = 3 m c = 8 m The frame is comprised of two…

Q: Determine the wind speed at a height of 40 m over surface terrain with a few trees, if the wind…

Q: Calculate the coordinates of the polygon

A: Data given Find : Coordinates of the polygon

Q: 1) For a falling head permeability test, the following are given. Determine the hydraulic…

A: The falling head permeability test is performed to determine the hydraulic conductivity of a soil…

Q: Problem 1: Determine rotation at C (8.) and deflection at C (ō) for the beam shown below. (Use the…

Q: Duties and responsibilities of the employers and the employees in relation to enforcement and…

A: OSH Standards refers to Occupational Safety and Health Standards which are a set of rules,…

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple…

Q: ) Rain fall over a basin in three consecutive hours are 10 mm, 20 mm and 10 mm respectively.…

Q: SITUATION 1: Given the truss below, calculate the stresses in members AB, BC, and CD if the…

Q: 6.64 Two square tubes of uniform thickness t are a shown in Figure P6.64. Determine the maxim terms…

Q: Determine the slope and deflection at the midspan of the supports of beam shown. El is constant.…

Q: Example / A sedimentation tank has width of 20m and height of 3m The Velocity of Flow is 5mm and the…

Q: 11) A truck is found to be able to service customers at a rate of 1.5 customers per minute. If they…

Q: A cantilever beam is having Young's modulus E = 2 × 105 N/mm², Moment of Inertia | = 8 x 107 mm4 and…

A: Given Data E = 2 × 105 N/mm2 I = 8 × 107 mm4 Deflection at free end (∆B) = 5mm Determine the…

Q: The A-36 steel column is encased in high-strength concrete as shown. If an axial force of 60 kip is…

Q: Complete the table below with the correct values in two decimal places, but "v" must be in five…

Q: The equilibrium position of a block of wood of density 'po' at the interface of liquid 1 and liquid…

Q: Please help me answer the first question

Q: A launching apron is to be designed at downstream of a weir for discharge intensity of 6.5 m³/s/m.…

Q: PROBLEMS (7) A SUSPENSION CABLE 140 M SPAN AND 14 M CENTRAL DIP CARRIES A LOAD OF 1 KN/M. CALCULATE…

Q: Calculate the bearing of line P-O. Ans.: S N77° 19'21'E Rored azimuth 113° 10'54" 47° 44'46" Q…

Q: 4. For the vessel containing glycerin under pressure, calculate the total pressure at the bottom of…

A: A vessel containing Glycerin under pressure. Depth of glycerin is h=2 m. Pressure above glycerin is…

Q: The duty of a crop is 432 hectares per cumec and the base period of the crop is 100 days. The delta…

A: Given: The duty of a crop, D = 432 Hectares per cumec. The base period of the crop, B = 100 days.

Q: The solid rod BC has a diameter of 40 mm and is made of an aluminum for which the allowable shearing…

A: Given, DBC = 40 mm τall(BC) = 30 MPa DAB = 35 mm τall(AB) = 60 MPa

Q: 1- It is said that Archimedes discovered his principle during a bath while thinking about how he…

A: Given, The density of gold is 19300 kg/m3 Weight of crown in air = 34.8N Weight of crown in water =…

Q: 1. Determine the internal determinacy of the given beam below. If determinate, solve for the…

A: Given data in question Load 20 kN/m Span 45 m 2 internal hinges To find out Indeterminacy…

Q: Explain the relationships in the excel graph

A: The given plots are to be explained.

Q: A single axial load of magnitude P is applied at end C of the steel rod ABC. Knowing that E= 30 x…

A: Given data:P=39 kips= 39×103lbE=30×106psid1(AB)=1.25 in.L1(AB)=4 ft=4×12=48 in.L2(BC)=3 ft=3×12=36…

Q: A BAR OF 30 MM DIAMETER IS SUBJECTED TO A PULL OF 60 KN. THE MEASURED EXTENSION ON GAUGE LENGTH OF…

Q: The rigid pipe is supported by a pin at A and an A-36 guy wire BD (E = 29 000 ksi). If the end C is…

A: Given:- A-36 guy wire E=29000 ksi C displaced = 0.75 in To find:- Deflection at point D in inches…

Q: A 100'x50' mat foundation (also called slab-on-grade) will be placed at the site shown in Figure 1.…

A: Given, Cc = 0.5 Cs = 0.1 σp = 1000 psf

Q: A 4 meter long steel plate with a rectangular cross section (10 mm x 50 mm) is resting on a…

A: Length of a steel plate, L =4 m Dimensions of plate = 50mm x 10mm Modulus of elasticity=200 GPa…

Q: Determine the reactions at the supports of the beam which is loaded as shown.

Q: Using rational method, rainfall intensity-duration curves and the data given in Fig. P 2.27 com-…

Q: Calculate the internal forces in the bar GF and GD in a roof truss as shown below. For each bar,…

A: Answer The forces in the bars GF & GD are FGF = -10.62 kN (Compression) FGD = 3.91 kN…

Q: Please draw a cross-section sketch and a plan view sketch showing the location and arrangement of…

A: - Span: 11 feet - Dead load: 20 psf - Live load: 100 psf - Self-weight: 87.5 lb/ft2 - Concrete…

Q: The field capacity of a soil is 25%, its permanent wilting point is 15% and specific dry unit weight…

A: Given - Field capacity (F.C.) = 25% = 0.25 Permanent wilting point (PWP) = 15% = 0.15 Depth of the…

Q: Example • A vehicle is driving at an initial velocity of 110 km/hr along a stretch of dry highway…

A: Given data: Initial velocity, V=110 kmhr Gradient, G=-4% Reaction time, t=1.5 sec

Concept explainers

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.

Question

A C250 x 30 American Standard channel beam is supported and loaded as shown here. When z = 1 m and 6 = 10 mm what is the maximum force this beam can support if the stress is
not to exceed 200 MPa?
Z
8
O
F
L
Multiple Choice
14.3 kN
Z
9.83 kN
5.12 kN
3.86 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which of the following is an allowable stress design concept. O Alternate Basic Load Combinations O OMn O 1.2D+1.6L O Rn = FyAg
A W18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 29 kips, w = 3.6 kips/ft, LAB = 6.4 ft, Lâc = 6.4 ft, and Lcp = 15.0 ft. Determine the magnitude of the maximum bending stress in the beam. A P LAB Answer: Omax = IH B LBC C W LCD D X
Quiz/ find the angle of rotation of the free end for the beam shown, then find the max sheaving stress If you know GAI = 28 GN/m² Gst=83 GN1m² GBV = 35 GN/m² Aluminum steel Bronzer Do d=100mm 3m d=75mm 2m 1.5m 1.5 KN.m
A T section of a beam is fabricated from 2 - 12 mm x 150 mm steelplates and joined by welding as shown in Figure ST - 904. It carries a live loadof 6.5 kN/m extending half of its span. Neglect the weight 1. Compute the maximum compressive stress. ( bending stress incompression )2. Compute the maximum tensile stress. ( bending stress intension )3. Compute the maximum shear stress. 4. Compute the shear stress between the junction of web and flange. 5. Compute the maximum deflection. EI is constant.
A steel section has the following properties: A = 0.012 m^2 rt = 0.053m tf = 0.016m Sx = 0.00208 m^3 d=0.210m Fy=248MPa The 5m Beam is subjected to an axial tensile load of 20 kN and a uniformly distributed lateral load of 15 kN/m. a. Compute the axial tensile stress if axial load only existed. b. Compute the axial tensile stress if bending only existed. c. Compute value of both axial and bending moment interaction value.
A W18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 18 kips, w = 5.8 kips/ft, LAR = 4.8 ft, LBc = 4.8 ft, and LcD = 16.4 ft. Determine the magnitude of the maximum bending stress in the beam. P х |C D LAB LBC LCD Answer: Omax = i 15.162 ksi
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
The working load P on the propped cantilever shown are each 150 kN. If the yield stress of mild steel is 300 MPa, determine the plastic section modulus in cubic millimeters, using a load factor of 1.75 against collapse. (express your response this way, x,xxX,XXX.X). Pu Pu 1.1 2m B A 2m 2m
A W18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 26 kips, w = 3.4 kips/ft, LAB = 4.0 ft, LBC = 4.0 ft, and LCD = 15.4 ft. Determine the magnitude of the maximum bending stress in the beam. A P LAB Answer: Omax = i B LBC C ksi W LCD D X
The beam shown in Fig. 3 carries a concentrated load of W and a total U.D.L load of 8 W. Determine the maximum safe value W that will not exceed allowable stresses provided in the table below. Group 0,(MPa) 0. (MPa) T (MPa) A 15 58 8 B 18 64 12 C 22 72 16 D 26 84 22 E 30 92 26 F 32 98 32 Im 8w 2 m Im RI R2 200 (Fig. 3)
Question 15 The design shear resistance, Vpl.Rd of a fully restrained simply supported Universal Beam with yield strength 345 N/mm² is 1,285 kN A point load of magnitude 1,906 kN is applied at the beam's mid-span The area of the web of the beam is Aw = 5,505 mm² The plastic modulus is Wpl.y = 2,979 cm³ The thickness of the beam web is tw = 12.6 mm Find the reduced design moment of resistance of the beam Mc,Rd (use the formula for l-cross-sections with equal flanges and bending about the major axis) Give your answer in kNm to the nearest whole number. Do not include units in your answer.
a) Two bars of different size form a pin-connected frame that supports a Load 'P' at point A as shown in the Fig. 3. What safe load P (kN) can be applied if the allowable stress of 120 MPa is not to be exceeded? Assume buckling has been prevented. Allowable stress is based on a factor of safety of 2.0. Cross sectional area of the rods AB and AC are given in the adjacent table as per last digit of Roll number. What is the failure load? Last digit of Area of AB | Area of AC Roll No. 1, 2, 4 & 7 200 mm 230 mm“ 3, 6 & 8 160 mm- 190 mm² 5, 9 & 0 180 mm 210 mm 2400 1600 Fig. 3 b) Two square bars are of equal length but have different size as shown in Fig. 4. Compare the maximum stress in the two bars if they are to receive the same input of energy from axial load. Given, m = (2 + last digit of your roll number). 2a 5.x m.x Fig. 4 last digit of roll=1