The equilibrium position of a block of wood of density 'po' at the interface of liquid 1 and liquid 2 is as shown in the figure. P₁ and P₂ are the densities of liquids 1 and 2 respectively. The ratio of volume of the block in liquid 2 to the total volume of the block is: (a) (c) P₁ P20 Po-P1 P2 - P1 Po - P2 P2-P1 ! Block Po (b) (d) Liquid-1 Liquid-2 Po-P₂ P₁-P2 Po-P1 P1-P2

The equilibrium position of a block of wood of density 'po' at the interface of liquid 1 and liquid 2 is as shown in the figure. P₁ and P₂ are the densities of liquids 1 and 2 respectively. The ratio of volume of the block in liquid 2 to the total volume of the block is: (a) (c) P₁ P20 Po-P1 P2 - P1 Po - P2 P2-P1 ! Block Po (b) (d) Liquid-1 Liquid-2 Po-P₂ P₁-P2 Po-P1 P1-P2

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Similar questions

Determine the BOD reaction rate constant, k, andultimate BOD, BODu.
At pH 5-7 aluminum hydroxide is O readily exceeding water quality limits for aluminum O leaving a foul taste in the water O in its least soluble form O ineffective as a coagulant
Determine the determinacy and stability of the following structures please show your complete solution
The assembly consists of a brass shell (1) fully bonded to a solid ceramic core (2). The brass shell [E = 115 GPa, a = 18.7 × 10-6/°C] has dout 50mm. and din = 35mm. The ceramic core [E = 290 GPa, α = 3.1 x 10-6/°C] has a diameter dout = 35mm. At a temperature of 15°C, the assembly is unstressed. AT = 60°C. Find the internal stress in the brass. = 200 mm Brass shell (1) (2) Ceramic core
The polyvinyl chloride bar is subjected to an axial force of 900 lb. If it has the original dimensions shown, determine the value of Poisson’s ratio if the angle u decreases by Δu = 0.01° after the load is applied. Epvc = 800(103) psi.
The block shown is made of a magnesium alloy for which E=X2GPaand ϑ=0.35. Knowing that σx= X1 MPa, determine (a) the magnitude of σyfor which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.
1. An element whose material has Sy = 280 MPa, Sut = 330 MPa, and Suc = 460 MPa is loaded as shown. Determine the safety factors of the following elements based on these criteria. (a) MSST (b) MDET (c) MNST = -40 MPa T Txy = 40 MPa σx = 30 MPa
Mechanics of Deformable Bodies The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa in the bronze rod? 21 -1.5 →1.5 Bronze Steel A = 900 mm2 E= 200 GPa L= 1.5 m A = 300 mm? E = 83 GPa L=2 m
Determine the ratio of RB/RA
A square high-density polyethylene [a = 158 × 10-6/°C] plate has a width of 295 mm. A 177 mm diameter circular hole is located at the center of the plate. If the temperature of the plate increases by 45°C, determine: (a) the change in width of the plate. (b) the change in diameter of the hole. Answer: (a) Aw= (b) Ad = i i mm mm
A bar with a constant cross section A is fixed at both ends. The bar is made of two different materials, that are joint together at point C. 1. a) What are the reaction forces, if an external force F is applied at point C? 2. b) Determine the normal force that is caused by a pure heating by AT. Est EAI ast Given: = 3, C a –-|e l– a → F- Steel Aluminium
Calculate Young's modulus for an iron crystal when tension is applied along [2 -2 1] direction. S11=7.6 (TPa)-', S12 = - 2.8 (TPa)-', S44 = 8.6 (TPa) -!