A cable with supports at the same elevation has a span of 400 m. The cable supports a uniformly distributed load of 6 kN/m along the horizontal. The maximum ten- sion in the cable is 5000 kN. Determine The angle between the cable and the horizontal at a support.

A cable with supports at the same elevation has a span of 400 m. The cable supports a uniformly distributed load of 6 kN/m along the horizontal. The maximum ten- sion in the cable is 5000 kN. Determine The angle between the cable and the horizontal at a support.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.23P: The center of gravity of the 850-N man is at G. If the man pulls on the rope with a 388-N force,...

See similar textbooks

Related questions

Q: Resolve the horizontal 660lb force as per figure below into components acting along the u and vaxes…

Q: 03 m k= 200 N /m 04m

A: according to the given details in the question.

Q: Determine the maximum allowable intensity w of the uniform distributed load that can be applied to…

A: Given : Allowable bending stress = 165 MPa Solution :

Q: Draw the Shear force diagram & Bending moment diagram for the cantilever beam as shown in figure,…

Q: Determine the shear force V in the beam at a point located 3.00 ft to the left of point B. The…

A: Given Data - A beam is given subjected to UDL and Point Load Reactions is Given as AY=2635.7 lb…

Q: Find the tension in each of the supporting cables in the figure when the weight of the crate is 500…

A: Given data: Weight of the crate, W = 300 N. Writing the projections along AD, AC and AB.

Q: PROBLEM 1.6 1.7 A level scaffold is to be supported at the center of a 12-ft ladder, as shown.…

A: TO FIND Required length x . and, angle ∅. CONCEPT USED Pythagorus theorum Triangle symmetry rule

Q: Two PARALLEL springs A and B has spring constants 269 N/mm and 91 N/mm, respectively. If the…

A: here, equivalent stiffness in parallel connection Keq. = 269 + 91 = 360 N/mm here, F = Keq. ×…

Q: A cable is loaded and supported as shown in Fig. Determine The length L of the cable. 5 m 1.5 m B 30…

Q: 2- Find the total change in length of the beam shown : A=200mm2 E2 = E3 = 150 GN/m² %3D 50 kN 30 kN…

Q: Q) Draw the S.F. and B.M. diagrams for the beam loaded as shown in Figure, inserting principal…

A: Let reactions at A and D are RA and RD respectively. Consider upward forces as (+)ve and downward…

Q: Determine the value of Elv (in Ib ft³ ) at the section below the load P for the beam loaded by two…

Q: The square timber used as a railroad tie carries two uniformly distributed loads, each totaling 48…

Q: Draw the free body diagram, shear force diagram, and bending moment diagram for section BC and AB of…

A: Drawing for section Bc,

Q: Two men are carrying on their shoulders a 500-N load suspended from a piece of bamboo 3 m long with…

Q: S+Roll No/2 kip 40+Roll No kip ft B 8 t

Q: Q/ Draw the S.F. and B.M. diagrams for the beam loaded as shown in Figure, inserting principal…

Q: termine the magnitude of the vertical force Cy for the simply supported beam, where w = 10 kips/ft,…

A: Ans: 38.5 kips

Q: Find the support reactions, draw the free-body diagram of the beams that shows the reactions and the…

Q: The bar supported by a pin at B and a cable at A carries a load of 260 N at C. Neglecting the weight…

Q: Determine the value of Elv (in Ib ft³ ) at the section below the load P for the beam loaded by two…

A: Let the pin end be "A", point at which load P acting is "B", point at which load Q acting is "C"",…

Q: Resolve the forces shown in the Figure below to two components Fx and Fy

A: The expression for the angle made by force F2 with the horizontal can be written as below,…

Q: Draw the Shear force diagram & Bending moment diagram for the cantilever beam as shown in figure,…

A: Taking resolution of vertical forces, RA=10+60+30+10RA=110 N Bending Moment at A,…

Q: For the given shear diagram, draw the actual load (indicate the position of the supports) and its…

A: We know that the shear force diagram is 1 degree higher than the actual loading diagram and the…

Q: A 200-lb man starts at end A of the wooden plank and walks toward end B. If the plank will fail when…

A: Given Data: Mass of the man, W=200 lb

Q: 5 m 150 KN B 5 m

Q: Determine the magnitude of the vertical force C, for the simply supported beam, where w = 8 kips/ft,…

Q: A 10-m uniform beam of weight 100 N is supported by two ropes at its ends. If a 400-N person sits at…

Q: 2- Belonging to the beam given below a) Find the reaction forces on supports B and D. b) Draw the…

A: Given data Determine 1] Reaction forces on supports B and D. 2] Draw the shear force and bending…

Q: Draw the free body diagram. 80 mg 60 20 650 mm 200 925 mm mm By

A: Solution: The free body diagram of the inclined beam is shown below:

Q: 400 N/m 200 N/m B 8 m

Q: For the beam I-section below, calculate the second moment of area about its centroidal x-axis…

Q: 8. For the beam shown, derive the expressions for V and M, and draw the shear force and bending…

Q: F2 R -20일 F3 30 25° 3LL1L1

Q: 600 lb 180 lb/ft 2' 6' 3 Determine the maximum negative moment using the shear and moment diagram…

A: Draw a diagram for the problem. Here, A, B, C, and D are the sections as shown in the figure, and…

Q: Q.3 / Determine the horizontal and vertical components on the beam at A and B. Neglect the weight of…

A: It is required to determine reaction force at A and B

Q: For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment…

Q: 60° 6 m 4 m 12 260 N

Q: Determine the resultant internal loadings acting on the cross section at ‘C’ of the machine shaft…

Q: 10 kN 10 kN A B 20 kN 3 m D 4 m 4 m

Q: Q4\ Draw the shear-force and bending-moment diagrams for a beam shown below 3000 N/m В A tosm-l -0.8…

Q: Determine the magnitude of the force exerted by the cable at B of the bar shown in Figure. 260 3.5 m…

Q: Draw the Shear force diagram & Bending moment diagram for the cantilever beam as shown in figure,…

A: Given data :- Cantilever beam Loads at points B =10 N ; 5m C = 60 N ; 3m D = 30 N; 2m E = 10 N; 5m

Q: For a bolt pattern in shear, if the line-of-action of the load passes through the centroid of the…

A: TRUE.

Q: Q3: Draw the S.F and B. M. diagrams for the beam shown below. P = 625 lb L = 4 %3 4 ft g 80 lb/ft…

Q: -240 mm C D 225 mm 1 225 mm 60 mm K 60 mm 135 mm 400 N

Question

A cable with supports at the same elevation has a
span of 400 m. The cable supports a uniformly distributed
load of 6 kN/m along the horizontal. The maximum ten-
sion in the cable is 5000 kN. Determine
The angle between the cable and the horizontal at a
support.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

The properties of the unequal angle section are Ix=80.9in.4,Iy=38.8in.4, and Iu=21.3in.4. Determine Ixy.
The center of gravity of the 850-N man is at G. If the man pulls on the rope with a 388-N force, determine the horizontal distance b between the man's feet and G.
Find the elevation h (km) where the weight of an object is one-tenth its weight on the surface of the earth.
Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
The end of a water hose weighing 0.5 lb/ft is pulled with a 40-lb force that is inclined at 14 to the horizontal. Determine the length s of the hose that is lifted off the ground and the corresponding horizontal distance L.
The intensity of the line loading acting on a quarter circle is w=w0(2/). Use intergration to determine the resultant of the loading and its line of action.
A rifle at A is fired at a target at B. If the speed of the bullet is 1400 ft/s, determine the rectangular form of the velocity vector v.
It can be show that a plane area may he represented by a vector A=A, where A is the area and represents a unit vector normal to the piano: of the area. Show that the area vector of the parallelogram formed by the vectors a and b shown in the figure is A=ab.
Show the complete solution, for this eq.
Determine the resultant force of the system shown below.
A roller coaster is shown below. Using the principle of work and energy,determine the minimum radius of curvature p for the track at B so that the passengers do notexperience a normal force greater than 4mg = (39.24m) N. Neglect the size of the car andpassengers.