Answered: a-Calculate the bearing in DMS from…

a-Calculate the bearing in DMS from Sta. A to Sta. C. b-Calculate the distance from Sta. A to Sta. C. c-Calculate the interior angle at Sta. A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2-42. Determine the magnitude and orientation, measured counterclockwise from the positive y axis,…

A: taking components of force on x-axisFx=FAsin30°-FBcosθFx=70012-600cos20°Fx=-213.4 Ntaking…

Q: Take A = 3 in? and E = 29(103) ksi for each member. Assume the members are pin connected at their…

Q: From the given data, compute the bearing of line 3-4 LINE BEARING DISTANCE 1-2 N 43 10' W 17.44m 2-3…

Q: 6.75 For this horizontal T through which water (p = 1000 kg/m³) is flowing, the following data are…

Q: A) Identify the best line. B) What is the forward and back bearing of the best line? C) Tabulate the…

A: It is given a open compass traverse and asked to calculate forward and backward bearing of the…

Q: Draw the FBD of member ABC 160 mm 90 mm 240 N

A: Forces acting on the member ABC are 240N external force Force at the B Force from the member CD

Q: The bearing of a line from A to B was measured as S 16°45' W. It was found out that there was a…

A: In surveying, bearing refers to the clockwise or anti-clockwise angle between the north or south and…

Q: Determine the location y̅ of the centroid C of the beam having the cross-sectional area shown.

A: Consider the labeled diagram of the I-section shown below. The expression for the area of section…

Q: 2–47. If the resultant force acting on the bracket is directed along the positive y axis, determine…

A: Writing the forces:

Q: Construct a detailed estimate of a roof shed of the given steel roof truss. Effective Span = 12 m…

A: Roof Shed The shed roof top, or shelter, is a rooftop having just one slant, or pitch. It is…

Q: The following are the true bearings of a closed traverse. Compute the interior angles of each side.…

Q: Determine the slope at point C of the given beam. Use E = 200 GPa, I = 6(106) mm4

A: Given data E = 200 GPA = 2 × 105 N/mm2 I = 6 × 106 mm4

Q: Given a true bearing of a line from X to Y as N 4° W where the magnetic declination is 16° W.…

Q: -80 mm J of 60 mm 5.29 The homogeneous wire ABCD is bent as shown and is attached to a hinge at C.…

Q: Q3: Compute the reduced bearings of all sides of the following trverse. If AB = S 72° 39'W %3D B A…

A: The reduced bearing or quadrantal bearing system of measurement measures the angle from the north or…

Q: Directions: Identify the corresponding bearing or direction for each given. Please observe proper…

Q: A rectangular plane surface 1m wide and 3 m deep lies in water in such a way that its plane makes an…

Q: For Problems 5.48 and 5.49, determine the area of reinforcing steel required for the T beams shown…

Q: *2-56. If the magnitude of the resultant force acting on the bracket is to be 450 N directed along…

A: For the given system of loading, the resultant given is 450 N and it is acting at an angle of 300…

Q: An equilateral triangle panel ABC with sides d = 2.0 m is hinged along BC and rests on a stop at the…

Q: The bearing if the line from A to B was measured as S 16°30' W. It was found that there was local…

A: The given data is: The fore bearing of AB=S 16°30' W=196°30' The fore bearing of AC=S 30°10'…

Q: Problem 6: If the resultant force acting on the bracket is required to be a minimum, determine the…

A: Given:- A bracket is given with three forces acting on it The magnitude of the first force = F1…

Q: Determine the values of S and Z and shape factor about horizontal x-axis. 14-in 2.5-in 2.5-in 1/2…

A: y = A1y + Ay2 +Ay3 A1 + A2 + A3⇒y = .5×6×3 + 16×.5×6.25 + .5×6×3.5×6 + 16×.5 + .5×6⇒y = 4.8571 in…

Q: center from the center of the bigger flange is: a) 31.56 mm

A: This question has been taken from engineering mechanics

Q: 5. If the resultant force Fr= {-300i + 650j +250k}N, determine the magnitude and direction angles of…

A: Given: The resultant force vector is {-300i + 650j + 250k} N. Consider the figure,

Q: -for the beam calculate the max bending and shearing stresses 3D 440 50fim 20 +2m+ 307 iy +300 4m…

A: Introduction : Maximum bending : When the shear force at that section is zero or changes sign, the…

Q: DETERMINE THE ADJUSTED BEARING LINES OF THE GIVEN BEARING FOR THE OPEN TRAVERSE FORWARD BEARING BACK…

Q: Locate the centroid y̅ of the beam’s cross-sectional area.

A: Consider the following figure:

Q: the midspan. The cross-sectional area of the beam is indicated t 190 mm

A: Find reactions :∑ MB=0RA(4)-10(4)(2)-0.5(2)=0RA=22.3KNRB=22.3KN

Q: Specify the location of FR on the beam, measured from point B.

A: this beam is simply supported beam and the load is applied in the downward direction then the…

Q: The beam is fabricated by attaching a C 180 x 15 channel to a W 250 x 18 shape with a 15 mm Ø rivets…

Q: 3. Solve the Open ended traverse below for the bearing at course FG: B 750 85° l030 145° E Bearing @…

Q: Given E = 29,000 ksi and 10O0 in, determine %3D the maximum shear (k) of the given beam. 3 kips/ft A…

Q: 2 k/ft Hinge 1 k/ft 10 ft 10 ft I k/ft 2 k/ft Hinge Hinge 10 ft A 15 ft- 15 ft

Q: 5. Determine the length and bearing of the omitted side. Unknown Beorlng Unknown Distanoe N65 38'E…

A: The given data is: S. No. Line Length Bearing as Quadrilateral Bearing Bearing as Whole Circle…

Q: Determine the allowable ultimate axial load on a rectangular short tied column 12 by 18 in. (300 by…

A: Given: Column dimensions = 300 x 450 mm Number of reinforcement bars = 6 Diameter of reinforcement…

Q: Y: Vertical Curved bar: smooth 6 lb slider: released from rest in (1), requires 2 (s) to slide to…

Q: 275 18 55 - H 145 -18 Dimensions in millimeters

A: Since the section 1 and 2 are symmetric, thus the area and the centroid from the bottom will be the…

Q: If the resultant force acting on the bracket isrequired to be a minimum, determine the magnitudes of…

A: Given Data: The magnitude of force F2 is 200 N. The magnitude of force F3 is 260 N. The angle which…

Q: Joint

Q: Use E = 200 Gpa and I = 140 x 106mmª. 40 kN ๓๐. 6m B 3m

Q: 7. Determine angle KPL from the given bearings. Draw the angles. a) PK, N 25°43’ W PL, S 79°12’ E

Q: 3.A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is…

A: Find value of a=?

Q: A) Determine the magnitude and orientation, measured counterclockwise from positive y axis, of the…

A: Given System FA=700 NFB=600 Nθ=20o

Q: Situation 1. If the resultant force acting on the bracket is FR = {650i + 250j – 300k} N, determine…

A: Given :- Two force F1 and F are given and resultant force vector is given FR = {650 i + 250 j −…

Q: The bearing of a line from A to B was measured as S 16°30' W. It was found that there was local…

Q: Situation2. Given: c&c, =W16x50: Ix=184in^4, C2, C3, Cg & Cg= W12x58: bx=475in^4, 91 = 92 =…

Q: 2-130. Determine the angles e and o made between the axes OA of the flag pole and AB and AC,…

A: The given figure is shown below

Q: Determine the allowable ultimate axial load on a rectangular short tied column 12 by 18 in. (300 by…

A: Given: Column dimension = 300 x 450 mm Number of reinforcement bars = 6 Diameter of reinforcement…

Concept explainers

Control Survey and Geodetic reductions

Control surveys or survey controls are used to establish reference points as a basis for various construction activities. Vertical and horizontal control points are to be established in a control survey to increase accuracy. After establishing the control points, all other types of surveys such as topographic, right-of-way, aerial mapping, construction layout, boundary surveys, and utility mapping can be worked upon so that control networks can be formed. The place from which the observations are made is called a survey station.

Question

a-Calculate the bearing in DMS from Sta. A to Sta. C.

b-Calculate the distance from Sta. A to Sta. C.

c-Calculate the interior angle at Sta. A.

Sta. A
X: 7,568.65'
Y: 4,346.44'
Not to Scale
S52°15'37"E 625.21'
Sta. C
X: 8,497.24'
Y: 4,214.08'
Sta. B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 (a)

VIEW

Step 2 (b)

VIEW

Step 3 (c)

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A triangular lot was formed by three straight lines AB, BC and AC with AB=95m and AC = 88m. Bearing of line AB is N45°E while bearing of line AC is due East. Point D is located at side AB which is 43m From A and is connected to point Ealong side AC. Area ADE IS 1|7 area of ABC.a) which of the following most neary gives thebearing aside BC.
A triangular lot ABC has a bearing and distance of line AB to be N 40deg E and 800mand CA equal to 960m long. The lot is to be divided such that the area of APO is only 1⁄4of the area of ABC. Point O is along the line AB and point P is along the line CA.Compute the distance AO and the dividing line PO. The area of triangle ABC is 300, 000sq. m. AP is equal to 600m long.
A triangular lot was formed bythree straight lines. Bearing of line AB is N45Eand is 160 m long; line AC and BC is 190 mlong. Point E is 100 m from A on side ABconnects point D on side AC which dividesthe area, making area AED to be 2/5 of thewhole area. Find the distance DE. a. 120.6 m c. 99.01 mb. 109.1 m d. 88.14 m
Choose one:628 kN 111 kN 262 kN 471 kN
A rectangular lot ABCD was laid out using triangulation methods and points were taken from station Y. Point A and B of the lot was found to be on the line YAB which has bearing of N60°E (point A was nearer to station Y). Point C on the lot was found to be east of Y. Point D of the lot was found to be on the line of YD with a bearing of S73°E . The distance from Y to C is 1000m and from Y to A is 466.0254m. a. draw the figure b. what is angle BYC c. what is angle BCY d. what is angle YBC e. what is the length of side BC on the lot? f. What is the length of side AD on the lot? g. what is the length of side AB and DC on the lot h. what is the area of the lot in hectares?
A rectangular lot ABCD was laid out using triangulation methods and points were taken from station Y. Points A and B of the lot was found to be on the line YAB which has a bearing of N60°E (Point A was nearer to station Y). Point C on the lot was found to be east of Y. Point D of the lot was found to be on the line YD with a bearing S73°E. The distance from Y to C is 1000m and from Y to A is 466.0254m. a) Draw the figure (SHOW THIS IN YOUR SOLUTION PAPER) b) Angle BYC c) Angle BCY
A rectangular lot ABCD was laid out using triangulation methods and points were taken from station Y. Points A and B of the lot was found to be on the line YAB which has a bearing of N 60° E (Point A was nearer to station Y). Point C on the lot was found to be east of Y. Point D of the lot was found to be on the line YD with a bearing of S73°E. The distance from Y to C is 1000m and from Y to A is 466.0254m. a) Draw the figure b) What is the angle BYC? c) What is the angle BCY? d) What is the angle YBC? e) What is the length of side BC on the lot? f) What is the length of side AD on the lot? g) What is the length of side AB and DC on the lot (round off to the nearest WHOLE NUMBER)? h) What is the area of the lot in HECTARES (round off to the nearest WHOLE NUMBER)?
it is desired to measure triangular lot AOB with the transit at pt O, but due to the fact that pt. O is on a swamp. The transit was set-up at pt. C which is 16m from pt. O. The bearing of the line CO in 90 degress north west, line CB is 60 degrees north east and line CA is due north or 0 degrees north east. line CA = 220m and line CB=220m a. find the angle A in triangle AOB? b. find the azimuth of the line OA? c. what will be the distance of the line OB?
A rectangular lot ABCD was laid out using triangulation methods and points were taken from station Y. Points A and B of the lot were found to be on the line YAB which has a bearing of N60°E (Point A was nearer to station Y). Point C on the lot was found to be east of Y. Point D of the lot was found to be on the line YD with a bearing S73°E. The distance from Y to C is 1000m and from Y to A is 466.0254m. a) Draw the figure (SHOW THIS IN YOUR SOLUTION PAPER)b) Angle BYCc) Angle BCYd) Angle YBCe) Length of side BC on the lotf) Length of side AD on the lotg) Length of side AB and DC on the lot (round off to the nearest WHOLE NUMBER)h) Area of the lot in HECTARES (round off to the nearest WHOLE NUMBER)
BY THE WAY P=66 KN
Two traverse lines AB and BC with the description: AB = 325.50 m, Due East, BC = 275.45 m, N 57045’ E meets at Sta V which is also at point B. If Sta PC is one fifth away from point B, find the stationing of PT if point A is at 20 + 150 m.
The area of a triangular lot is to be computed, given the following trials for stadia interval factor: 102, 93, 97, 99, 104 and 107. The lot has its boundary named as A, B and C while the instrument is placed somewhere inside the lot. Point A is at N15°E with a stadia intercept of 1.211, rod reading of 1.926 m and an angle of -2°. Point B is at S65°E with a stadia intercept of 1.356, rod reading of 2.450 m and an angle of +1°20’ and Point C is at S30°W with a stadia intercept of 1.444 rod reading of 1.871 m with 0°. Determine the area of the lot if the instrument used has internal focusing. Please show complete solutions. Thank you.