A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal force component on the cross-sectional area at the point A is (in kN) Figure 1: y P = 400 kN 30° 1000 mm A Area 30 mm
Q: The carbon content in Manganes- Steel (1345) in SAE/AISI classification system is 0.45 % O 0.13 % O…
A:
Q: 2. Determine the internal load expressed in Ib-ft 2 of a brake that requires 900 in-lb of torque to…
A:
Q: A 21-tooth sprocket is connected to a 63-tooth sprocket by means of RC 60 having 180 pitches.…
A:
Q: 6- A liquid has a specific weight of 59 lb/ft and a dynamic viscosity of 2.75 lb s/ft?. Determine…
A:
Q: The center of gravity can be outside of the plane. (A) True B) False
A:
Q: For the cantilever beam shown. find the value of Normal stress due to :axial load at point E 4 KN 6…
A: Given:P= 2 KNPt=4 KNM=6 KN.mL=10 m
Q: A steam turbine operates with 1.6 MPa and 350°C steam at its inlet and saturated vapor at 30°C at…
A: State 1: P1= 1.6 MPa T1= 350∘C State 2: Saturated vapor condition T2= 30∘C Mass flow rate, m˙= 22…
Q: According to the figure, the vector equation is VA/B=vA-vB VA= vB+vA/B vB=vA+vA/B Option 4
A: find the relation between velocity of A and velocity of B.
Q: is used to cut machine other material. O Chromium steel O Nickel steel O Martensitic tool steel O…
A:
Q: Consider a 210 MW steam power plant that operates on a simple ideal Rankine cycle, steam enters the…
A:
Q: iven that the weight density of water is 9810 N/m3, calculate the fluid force (in Newtons) on a…
A: Given Weight density, w = 9810 N/m3 Depth, h = 4 m Area of plate, A = 1.1 x…
Q: 1. Plot the four locations in the psychrometric chart and determine the other properties for each…
A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…
Q: A one-degree-of-freedom system is subject to a harmonic excitation whose magnitude is proportional…
A: Given DataAmax=9mmA=2mmfi=200Hz Finding the Damping ratio
Q: 50* POINT A 200 POINT I
A:
Q: A car has two devices attached to its tire which are triggered when objects pass in front of them.…
A: Given : D = 1.3 m d = 0.6 m s = 0.182 To find : H0
Q: A uniform circular thin rod of radius 10 in. is attached to a pin at C and to the cable AB. Find the…
A:
Q: Q.1) Determine the coordinates of the centroid of the y = area. 2 mm Answer: 4 mm
A:
Q: Q2: Can cBN be used in honing stick in single layer configuration?
A: Yes, CBN can be used in honing stick in single layer configuration. Honing stick with CBN makes…
Q: Example 1: The simply supported beam in Fig. (a) carries two concentrated loads. (1) Derive the…
A:
Q: 2. An undivided road has a design speed of 85 km/h. Initial cross slope of the road surface is 2%,…
A:
Q: The food compartment of a refr °C by removing heat from it at refrigerator is 2 kW. Determine and…
A: Given: Win = 2 kW QL = 360 kJ/min
Q: The last two digits in aluminum alloys * identify . O aluminum alloy aluminum content aluminum tool…
A: In alluminium alloys, major component is alluminium and other alloying element like magnesium,…
Q: A 1 lbm/s fluid enters a machine at 170 m/s, 800 kPa, and with a specific volume of 0.3 m³/kg. The…
A: Solution - Given data -mass flow rate m =1 lbm/s =0.453 kg/sv1 =170 m/sv2 =330 m/sp1 =800 kPap2 =138…
Q: Multi-evaporator systems are When the required temperature lift is small When the required…
A:
Q: Q2. The system shown below is in equilibrium. Find the reactions at A (hinge support) and the force…
A: find the reaction at pin support A and force at point B.
Q: In a simple Rankine cycle, the steam throttled condition is 8 MPa and 480°C. The steam is then…
A:
Q: 2. In an ammonia vapor compression refrigeration cycle, 5 kg/min of refrigerant are circulated. The…
A:
Q: 1. Explain the difference between stoker, CFB, and PC from the three types of steam generators,…
A: CFB (Circulating Fluidised Bed) Boiler The circulating fluidized bed (CFB) is a developing…
Q: Please do the activity shown below. Use pre-specified tolerance of 0.001. Given are the following…
A:
Q: Technician A says that the PCM illuminates the mil if a defective causes emission levels to exceed…
A: If the emission level exceeds the threshold limit then PCM illuminates the mil. But it is not only…
Q: DR LARISA MALYSHEVA QB1 DIRECT STRESS Two round solid bars of different materials are connected (in…
A: given; load(P)=190KN =190*103Ndiameter of steel bar(ds)=18mmdiameter of aluminium…
Q: A 120 MW gas turbine power plant running on Ideal Brayton cycle has the following initial…
A: Net work, W˙net= 120 MW Initial temperature, T1= 22∘C= 22+273 K= 275 K Initial pressure, P1= 95 kPa…
Q: Thermodynamics (Brayton Cycle) Round up the answer up to 5 decimal places. A 120 MW gas turbine…
A:
Q: 200 N 200 N 500 N 200 N A C D E 300 225 300 225 Dimensions in mm Fig. P5.14
A:
Q: Find the angle between the two given vectors. u = (1, -4, 1), v = 3(0,2, -2) Write your answer in…
A:
Q: A flywheel rotating at 500 rpm decelerates uniformly at a 3 rad/sec². How many seconds will it take…
A: N=500rpm Angular velocity of flywheel,w=2*π*N/60 w=2*π*500/60=50*π/3=52.36rad/sec Angular…
Q: require at least 4.5 HP to deliver the volume of air needed. The owner has also a second hand motor…
A:
Q: Determine the moment of inertia about the x-axis for the cross-section of the beam shown below.
A:
Q: 1. An automobile travels to the right at a constant speed of 20 m/s. If the diameter of a wheel is…
A: An automobile travels to the right at a constant speed of 20 m/s. Hence, VA= 20 m/s (→). Diameter of…
Q: An ideal gas refrigeration cycle using air as the working medium is to maintain a…
A: For ideal gas refrigeration cycle, COP=1/{(rp)^y-1/y}-1} =1/[(4)^{1.4-1/1.4}-1] =2.057=2.06
Q: -Q4 Eind the ut come of the Convergent forces system in the figure below Pease. 450 200 38 *300N
A:
Q: What is the Wave Machine? The below animation and diagram show a wave machine at Stonybrook…
A: Given question: What is the Wave Machine? The first wave measures 2 inches from the gray line to the…
Q: A uniform circular disk 3ft in diameter weighs 960lb. what is its moment of inertia abouti ts usual…
A: Given: m = 960 lb r = 3ft
Q: Calculating the Cooling load of refrigeration for the Chiller and the Electrical Energy Consumed by…
A: Given: To find: kWR, kWE and COP “Since you have posted a question with multiple sub-parts, we will…
Q: A meeting hall is to be maintained at 25°C, 18Cwb. The space has a cooling load of 40kW of which…
A:
Q: Given that the weight density of water is 9810 N/m3, calculate the fluid force (in Newtons) on a…
A: Given data :- weight density = 9810N/m^3 dimension of plate = 1.4m ×1.4 m depth = 2 m find the…
Q: What is the maximum normal stress, MPa, due to bending? For W200x22.5, S = 194um^3. Answer in whole…
A: Given data :- for W200×22.5 S = 194×10^(-6) m^3 find the maximum normal stress ..
Q: what is the unit of the medium resistance and the specific cake resistance
A: Given Resistance To find Unit of Cake resistance Unit of Medium resistance
Q: CHOOSE THE CORRECT ANSWER! Three pipes of 400 mm, 350 mm and 300 mm diameter are connected in…
A:
Q: Problem No.4 Two long parallel wires are 4 cm apart and carry currents of 2 A and 6 A in the same…
A:
Step by step
Solved in 2 steps with 1 images
- A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
- On the surface of a structural component in a space vehicle, the strains arc monitored by means of three strain gages arranged as shown in the figure. During a certain maneuver, the following strains were recorded: e, = 1100 X l0_6, 6h = 200 X lO_6, and e = 200 X 10-6. Determine the principal strains and principal stresses in the material. which is a magnesium alloy for which E = 6000 ksi and v = 0.35. Show the princ ipal strains and principal stresses on sketches of properly oriented elements.A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?A bungee cord that behaves linearly elastically has an unstressed length L0= 760 mm and a stiffness k = 140 N/m. The cord is attached to two pegs, distance/? = 380 mm apart, and is pulled at its midpoint by a Force P = 80 N (see figure). (a) How much strain energy U is stored in the cord? (b) What is the displacement Scof the point where the load is applied? (c) Compare the strain energy (with the quantity PSC12. Note: The elongation of the cord is not small compared lo its original length.
- A W 8 × 28 beam of a length 10 ft is held between immoveable supports. The beam has a modulus of elasticity E = 29,000 ksi and coefficient of thermal expansion a = 6.5 ×10-6 /?. If the temperature of the beam is raised uniformly by an amount AT = 20°F, calculate the thermal stress aTin the beam.An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material of the bar has the stress-strain curve shown in the figure. Determi ne t he elongation 5 of the bar for each of the following axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN. and 45 kN. From these results, plot a diagram of load P versus elongation 5 (load-displacement diagram).
- -7 The truss A BC Shawn in the figure supports a horizontal load P1= 300 lb and a vertical load P2= 9001b. Both bars have a cross-sectional area A = 2.4 in2 and are made of steel with E = 30 X 106 psi. (a) Determine the strain energy U1of the truss when the load P1acts alone (P2= 0). (b) Determine the strain energy U2when the load P2acts alone (P1= 0). (c) Determine the strain energy U3when both loads act simultaneously.7.5-11 in. cube of concrete (E = 4.5 X 106 psi. v = 0.2) is compressed in biaxial stress by means of a framework that is loaded as shown in the figure. Assuming that each load F equals 25 kips. determine the change iv in the volume of the cube and the strain energy U stored in the cube.A bar with a circular cross section having two different diameters d and 2d is shown in the figure. The length of each segment of the bar is L/2T and the modulus of elasticity of the material is E. (a) Obtain a formula for the strain energy U of the bar due to the load P. (b) Calculate the strain energy if the load P = 27 kN, the length L = 600 mm, the diameter d = 40 mm, and the material is brass with E = 105 GPa.