A center-tapped rectifier with a line voltage of 120 V(rms), 60 Hz has a turn ratio of 5:1, a filter capacitance of 470 μF, and a load resistance of 1.5k. Use complete approximation (where diode voltage V₁ = 0.7V and forward resistance of 502) to calculate the dc load current.

A center-tapped rectifier with a line voltage of 120 V(rms), 60 Hz has a turn ratio of 5:1, a filter capacitance of 470 μF, and a load resistance of 1.5k. Use complete approximation (where diode voltage V₁ = 0.7V and forward resistance of 502) to calculate the dc load current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 4. The value of dc current (Idc) in amperes is ? 5. The value of the output peak voltage (Vpout) in volts is ? 6. The value of peak secondary voltage (Vpsec) in volts is ? 7. The value of primary peak voltage is (Vppri) in volts is ?
27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is ? 2. The value of the dc voltage (Vdc) in volts is ? 3. The value of the ripple factor is ?
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 18 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 6 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1100 and N2 is given as 600, compute for the primary peak voltage. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is..... 2. The value of the dc voltage (Vdc) in volts is..... 3. The value of the ripple factor is..... 4. The value of dc current (ldc) in amperes is..... 5. The value of the output peak voltage (Vpout) in volts is..... 6. The value of peak secondary voltage (Vpsec) in volts is..... 7. The value of primary peak voltage is (Vppri) in volts is.....
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 5 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1400 and N2 is given as 500, compute for the primary peak voltage.
Draw the V-I characteristics of SCR,MOSFET,IGBT,DIAC and TRIAC
A HVDC link is operating with 175 KV AC line voltage at the rectifier. When the DC current is 1100 Amps, the rectifier delay angle is 100 and inverter extinction angle is 200. The resistance of the line is 23 ohms and the commutating reactances of the rectifier and inverter are 22 ohms and 21 ohms. Calculate the DC voltages at the rectifier and inverter terminals and the AC line voltage at the inverter.
Prepare the comparison table for the Power semiconductor devices 1)Integrated gate-commutated thyristor (IGCT) 2) Static induction thyristor (SITH) 3)Static induction transistor (SIT) .(Symbol, VI characteristics, Application, Voltage & Current rating)
2.-Discuss the difference between the terms “sink” and “source” as relatedto current loading of a microcontroller.
The input network voltage of the 1-phase bridge type rectifier was measured as 220 2 V peak. If the trigger angle is selected as 110 degrees, which of the following statements is correct? A) The average value of the output voltage is positive and is about 88.6 V. B) The average value of the output voltage is negative and about 127.3 V. C) The inverter is not in mode. D) The average value of the output voltage is negative and about 67.7 V. E) None
Subject:Electronics Engineering How JFET has been constructed? Explain the principle of operation of JFET at different values of VGS and VDS
2. Given:VCC: 16 voltsRB1: 7000 ohmsRB2: 50 ohmsRB3: 50 ohmsRB4: 1500 ohmsB=beta: 100RE: 750 ohmsRC: 500 ohmsVCE: ? volts
Prepare the comparison table for the Power semiconductor devices 1)Integrated gate-commutated thyristor (IGCT) 2) Static induction thyristor (SITH) 3)Static induction transistor (SIT) .(Symbol, VI characteristics,