A centrifugal pump having four stages in parallel delivers 12 kiloLiters per minute of liquid against a head of 25m. The diameter of the impeller being 24 cm has a speed of 1800 rpm. A pump is to be made up with a number of stages in series. In similar construction to that of the first pump to run at 1250 rpm and to deliver 15 kiloLiters/min against a total head of 250 m, find the number of stages required in this case.

A centrifugal pump having four stages in parallel delivers 12 kiloLiters per minute of liquid against a head of 25m. The diameter of the impeller being 24 cm has a speed of 1800 rpm. A pump is to be made up with a number of stages in series. In similar construction to that of the first pump to run at 1250 rpm and to deliver 15 kiloLiters/min against a total head of 250 m, find the number of stages required in this case.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A plant has installed a single suction centrifugal pump with a discharge of 68 m3/hr under 60 m head and running at 1200 rpm. It is proposed to install another pump with double suction but of the same type to operate at 36.27 m head and deliver 90 m3/hr. Determine the speed of the new pump. What should be the new impeller diameter if the diameter of the original pump is 140mm?
It is desired to pump 50 ft3/s of water at a speed of 22 r/s,against a head of 80 ft. (a) What type of pump would yourecommend? Estimate (b) the required impeller diameterand (c) the brake horsepower.
A centrifugal pump having four stages in parallel, delivers 12 kiloliters per minute of liquid against a head of 25m. the diameter of the impeller being 24 cm and a speed of 1800 rpm. A pump is to be made up with a number of stages in series. In similar construction to that the first pump to run at 1250 rpm and to deliver 15 kiloliters/min against a total head of 250m. find the diameter of the impellers and the number of stages required in this case.
The manometric head developed by a three-stage centrifugal pump runningat 450 rpm is 60 m. The width and diameter of each impeller at the outlet are60 mm and 750 mm, respectively, with outlet blade angle 45°. Determine itsmanometric efficiency, if discharge through the pump is 0.3 m^3/s.
1. A centrifugal pump with 30 cm impeller delivers 30 l/s against a head of 24 m when running at 1750 rpm. What will be the delivery of a homologous pump of 15 cm impeller diam eter assuming same efficiencies and speed? 2. A centrifugal pump with 2.3 diameter impeller running at 327 rpm delivers 7.9 m3/s of water. The head developed is 72.8 m. The width of the impeller at outlet is 0.22 m. If the overall efficiency is 91.7% determine the power to drive the pump.
For a centrifugal pump of impeller diameter D rotating at N to develop a head of H and discharge Q, what would be the new head developed by the same pump if we halve the impeller speed to N/2? H/A 2H H 4H H/2
The pressure gage leading to the turbine casing of a Francis turbine reads 0.5 MPa and the center of the spiral casing is 5 m above the tailrace. What is the net head if the velocity of the water entering the turbine is 10 m/s?
A pump is designed to deliver 9500 L/min of water at a required head of 8 m. The pump shaft rotates at 1100 rpm. The pump specific speed in nondimensional form is (a) 0.277 (b) 0.515 (c) 1.17 (d ) 1.42 (e) 1.88
A multi stage pump is required to deliver of 2 l/s water against a maximum discharge head of 240 m. The diameter of radial bladed impeller should not be more than 15 cm. Assume a speed of 2800 rpm. Determine the impeller diameter, and power. Overall efficiency is 0.7.
A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. After resolving the turbine speed, what horsepower would be developed under a head of 11 meters?
A pump is required to deliver 120000 lpm of water at a head of 25 m. A motor which spins at 450 rpm is available. What kind of pump geometry should be used? Estimate the power requirement of this pump.
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.3.1 Find the maximum allowable speed to operate the pump3.2 What power is expected in overcoming friction at this speed, take ƒ = 0.01