A certain cable, 504.76 ft long is suspended between two supports at the same elevation and 500 ft apart, the load is 500 lbs per horizontal foot including the weight of the cable. Calculate the sag of this cable using Newton-Raphson method up to 5 iterations with initial guess of d (sag) 10 ft. Use parabolic equation. Parabolic Equation: 8d? s = L+ 3L 32d4 5L3 Where: S length of the cable distance between two supports

A certain cable, 504.76 ft long is suspended between two supports at the same elevation and 500 ft apart, the load is 500 lbs per horizontal foot including the weight of the cable. Calculate the sag of this cable using Newton-Raphson method up to 5 iterations with initial guess of d (sag) 10 ft. Use parabolic equation. Parabolic Equation: 8d? s = L+ 3L 32d4 5L3 Where: S length of the cable distance between two supports

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Slenderness ratio of a 5 m long column hingedat both ends and having a circular cross sectionwith diameter 16 cm is..
Q7. A 4.20 m long (L) steel pipe has a mass of 450 kg and is lifted by a crane attached to cable CD. Point C is attached to each end of the pipe at A and B of the steel pipe. The length AC is 3.25 m and the length BC is also 3.25 m (i.e., length AC = BC). Using g = 9.81 m/s2, calculate the tension in sling AC and give your answer in newtons (N) to the nearest newton.
3. A 3-meter-long beam is used to support a heavy object. The object has a uniform distributed load of 6 kN/m on the entire beam. The Young’s modulus and moment of inertia of the beam are 200 GPa and 5×105 mm4, respectively. The beam is supported at three positions as shown below. (a) Label the element and node numbers (either on the figure or with a new simple sketch). (b) Determine the slopes at the three support positions of the beam.
The dimensions are of the graph are d1 = 7 cm , L1 = 6 m , d2 = 4.2 cm , and L2 = 5 m with applied loads F1 = 130 kN and F2 = 60 kN . The modulus of elasticity is E = 80 GPa . Use the following steps to find the deflection at point D. Point B is halfway between points A and C. What is the reaction force at A? Let a positive reaction force be to the right.
a. An overhead line has the following data: Span length= 160 m Conductor diameter= 0.95 cm Weight per unit length of the conductor= 0.65 kg/m Ultimate stress= 4,250 kg/cm2 Wind pressure= 40 kg/m2 Safety factor= 5 Calculate the sag? b. Derive the expression for the lowest point of the catenary curve if the supports are at different levels. Given that weight of conductor= 0.35 kg/m. Maximum allowable tension= 800 kg. Span length= 160 m and safety factor = 2. Find minimum point of catenary if supports are at 70 m and 60 m.
A load weighing P kN aswith AB, AC and AD cables such asare carried. Points A and B are x-axis, Cand D points are on the y-z plane.Specific to your name in the data tableAB, AC and AD cable using ratingsCalculate the forces. P (kn) = 440 L1 (m) = 11 L2 (m) = 10 L3 (m) = 16 L4 (m) = 18 L5 (m) = 16 L6 (m) = 5
An 87.5 kg fisherman sits at the center of the boat, which has a uniform width and a weight per linear foot of 4.1 lb/ft. The boat is 13 m long. Assume that the water exerts a uniform distributed load upward on the bottom of the boat. a. What is the applied load (lb) applied to the boat due to the weight of the fisherman? Round up to the next whole value.b. Using the applied load at Item 9.a, what is the maximum shear force (lb) exerted on the boat?c. What is the maximum bending moment (lb-ft) exerted on the boat?d. At what distance from the left side of the boat the maximum bending moment occurs?
2. Ships and sailing vessels often carry lead ballast in various forms, such as bricks, to keep the ship properly oriented and upright in the water. Suppose a ship takes on cargo and the crew jettisons a total of 0.500 m3 of lead ballast into water 2 000 m deep. Seawater's density is equal to 1.025 g/cc while lead's bulk modulus equals to 42.0 GPa. Calculate the weight of water in a column with cross section of 1.00 m2. 20.1 MN 22.1 GN 21.1 MN 21.1 GN 22.1 MN 20.1 GN Find the change in the pressure at 2.0 km depth. 21.1 MPa 21.1 GPa 20.1 GPa 22.1 MPa 20.1 MPa 22.1 GPa Find the change in the volume of the lead at 2.0 km depth. -0.000 30 cubic meter -0.000 28 cubic meter -0.000 24 cubic meter -0.000 26 cubic meter -0.000 34 cubic meter -0.000 32 cubic meter
A sectional steel cable of 3.00 cm2 has a mass of 2.40 kg per meter. If the cable is 500 m long hanging on a vertical cliff, how far the cable is stretched due to weighs itself? Known young steel modulus 2.00 x 10¹¹ N/m2 . (b). If there are two climbers hanging on the cable, determine how far cable is stretched. The mass of climbers is 60 kg and 70 kg, respectively.
• A uniform aluminum beam 9.00 m long, weighing 300 N, rests symmetrically on two supports 5.00 m apart (Fig. E11.14). A boy weighing 600 N starts at point A and walks toward the right. (a) In the same diagram construct two graphs showing the upward forces FA and FB exerted on the beam at points A and B, as functions of the coordinate x of the boy. Let 1 cm = 100 N vertically and 1 cm = 1.00 m horizontally. (b) From your diagram, how far beyond point B can the boy walk before the beam tips? (c) How far from the right end of the beam should support B be placed so that the boy can walk just to the end of the beam
A beam of 8m length rests on two supports one at the right end and the other 2m from the left end. The beam carries a udl of 15kN/m over the entire span and a concentrated load of 80kN at the middle of its span. Draw SFD and BMD . Mark all salient values and locate point of contra-flexure. Ans: RB = 120kN, MC = 172.5kNm, x1 = 0.343m from B. answer must tally with those given
A board of mass mand length l is attached to a wall and a rope that makes an angle of theta, as shown. A block of mass M hangs from the right end of the board. Suppose m = 2.0kg, L = .60m, M = 0.50kg, and angle(theta) = degrees. a. Using numbers, what is the magnitude of the tension force in the rope connecting the board and wall? b. Using numbers, what is the magnitude of the force applied by the hinge? c. Using numbers, in what direction does the force applied by the hinge point?