A circuit has a large motor connected to AC power line (w=100 r/s) .The motor model is a resistor in series with an inductor as shown.Motor apparent power|s| = 120 VAMotor Effective Voltage V,m, = 220/30° VFind Z, the impedance of the motor model82Find p.f., the motor power factor50mHFind S, motor complex powerFind Ime , motor effective currentFind P, the motor average powerFind Q, the motor reactive power

The impedance of the motor model will be R2+(wL)2∠tan-1wLRputting the value we…

A circuit has a large motor connected to AC power line (w-100 r/s). The motor model is a resistor in series with an inductor as shown. Motor apparent power Is| = 120 VA Motor Effective Voltage V,.=220430° V Find Z, the impedance of the motor model Find p.f., the motor power factor Find S, motor complex power 50mH

A circuit has a large motor connected to AC power line (w-100 r/s). The motor model is a resistor in series with an inductor as shown. Motor apparent power Is| = 120 VA Motor Effective Voltage V,.=220430° V Find Z, the impedance of the motor model Find p.f., the motor power factor Find S, motor complex power 50mH

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Similar questions

A 90-ohm resistor, a 32 mH inductor, and a 5 uF capacitor are connected in series across the terminals of a sinusoidal voltage source, vs = 125∠-60° V. If the angular velocity is ω = 5000 rad/s, find: a. The value of capacitance that yields a steady-state output current i with a phase angle of -105°. Express your answer in 2 decimals. b. The magnitude of the steady-state output current i. Express your answer in the nearest whole mA.
The frequency of the sinusoidal voltage sourcein the circuit is adjusted until ig is in phase with vg.1. What is the value of ω in radians per second?2. If vg=15 cosωt V (where ω is the frequency found in [a]), what isthe steady-state expression for ig?
A 200V, 50 Hz sinusoidal supply is connected to a parallel network comprising three branchesA, B and C as follows: A, a coil of resistance 3 ohm and inductive reactance 4 ohm; B, a seriescircuit of resistance 4 ohm and capacitive reactance 3 ohm; C, a capacitor. Given that the powerfactor of the combined circuit us unity, find (a) the capacitance of the capacitor inF; (b) the current taken from the supply. [Ans. 127.32 F, 56A]
A transmission line has a reactance of 1 Pu is operating at Vs = Vr = 1 Pu. The generator is connected at source end which is delivering 0.5 Pu of active power and the transmission line is compensated with a series capacitance of 0.5 Pu. Find the load angle with series capacitance compensation ?
The feeder is to be used with an antenna for which an inductive reactance is measured as j60 Ohms at 1.7 MHz. The resistive part of the antenna’s impedance is measured as 80 Ohms. Using the online impedance matching calculator, design a suitable impedance-matching network for each of the two cables if the coaxial cable has a characteristic impedance of 75 Ohms and the twin lead cable has a characteristic impedance of 300 Ohms, so that the inductance is in the longitudinal branch, while the capacitor is in the transversal branch of the impedance matching network. Do not round the resulting values.
The frequency of the sinusoidal voltage sourcein the circuit is adjusted until the current io is in phase withvg.1. Find the frequency in hertz.2. Find the steady-state expression for ig (at the frequency found in[a]) if vg=90 cosωt V.
For the frequency-domain circuit , calculate: 1. a) the rms magnitude of Vo;2. b) the average power dissipated in the 9 Ω resistor;3. c) the percentage of the average power generated by the idealvoltage source that is delivered to the 9 Ω load resistor.
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
An AC circuits with 50 Hz voltage of 240V effective value is impressed on aninductance of sin(Y+2)/5 H. Y is the last digit of student matrix no. For example, astudent with the matrix number CD150012 will have the values of Y = 2, thereforesin(2+2)/5 H. i) Write the time equation for the voltage V(t) and the resulting current. Let thezero axis of the voltage wave be at t = 0.ii) Sketch the phasor diagram for this circuitiii) Find the maximum energy stored (joules) in the inductance.
A circuit is constructed with an AC generator, a resistor, capacitor and inductor as shown. The generator voltage varies in time as ε = Va - Vb = εmsinωt, where εm = 120 V and ω = 429 radians/second. The values for the remaining circuit components are: R = 61 Ω, C = 426 μF. The value for L is unkown. What is known is that the voltage across the generator leads the current in the circuit by φ = 48 degrees. 1) What is t1, the first time after t = 0 when the magnitude of the voltage across the inductor is maximum? 4) What is VL,max, the magnitude of the maximum voltage across the inductor? 5) What is VL = Vb - Vc, the voltage across the inductor, at time t = 0? Note that VL is a signed number.
The figure below shows an RLC electrical network operating on alternating current. A load impedance Z of unknown value has been connected to the output of said network. a) Find the value of the load impedance Z, which is necessary to connect to the output of the given network to obtain the maximum average power transfer.b) Determine the value of the maximum average power transferred to the load found in the previous section.Note, the values of all impedances shown in the circuit are given in Ohms.
The device is represented in the frequency domain bya Norton equivalent. When a resistor having an impedance of 5 kΩ isconnected across the device, the value of V0 is (5–j15) V. When acapacitor having an impedance of −j3 kΩ is connected across the device,the value of I0 is (4.5–j6) mA. Find the Norton current IN and theNorton impedance ZN