A circuit has a the following characteristics: Vth = 1.92 V Rth = 42.9 ohms RL varies from 10 to 100 ohms a) Find the range of voltages across the load: min voltage: 362.94 mV (enter onl numerical part. Your answer should be in mV) max voltage: 1.34 V (enter only numerical part to the HUNDREDTHS place. (2 decimal places)) b) What is the max power that can be delivered the load

A circuit has a the following characteristics: Vth = 1.92 V Rth = 42.9 ohms RL varies from 10 to 100 ohms a) Find the range of voltages across the load: min voltage: 362.94 mV (enter onl numerical part. Your answer should be in mV) max voltage: 1.34 V (enter only numerical part to the HUNDREDTHS place. (2 decimal places)) b) What is the max power that can be delivered the load

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Draw AC and DC equivalent circuit for the circuit given in Figure 4
please write introduction about AC Circuits and Parallel Circuits
B.. What is the load current for the circuit shown in the figure? Please choose one: a. 6.0 mA b. 3.0 mA C. 9.0 mA D. 7.5 mA
Explain the basic concepts of direct current and alternating current. Give an example with formulas and results for each of them.
What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
a) Graphically show the differences between alternating current voltage (A.C) and direct current voltage (D.C). What are the advantages of A.C compared to D.C?
The voltage regulation can be equal to zero :when .The t and current is not too highO .The p.f. is leading p.f. for any possible current O .The p.f. is lagging p.f. for rated current O
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.
Three phase Bridge rectifier operated from a 380V, 50Hz source throughout three-phase Y/Y connected transformer with ration 2:1. The load current has continuous character with negligible ripples and average thyristor current of 15A. The circuit inductance per phase is 1.2mH. The rectified voltage due to overlapping angle is 90 % of that voltage when this angle is neglected. 1- How much will the voltage drop be due to circuit inductance * 2- How much will the dc average voltage Vdc(alpha) be. 3- How much will the firing angle be ? 4- The overlapping angle. 5- How much is the percentage change of the output dc power if the thyristors T2, T4 and T6 are replaced by three diodes D2, D4, D6. 6- How much will be the maximum RMS phase current for the mentioned in previous task circuit ( semi-converter). 7- If an additional of 1 mH inductances are added to the existing inductances in the phases , how much will the overlapping angle be. The dc load current is kept constant & the…
An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?