A sensitive ammeter (micro-ammeter) is used to manufacture an analog DCvoltmeter. The ammeter has the characteristics: 100uA full-scale indication, internalresistance Rix200ohm.VllmeterRsMeenel VaageCalculate the seties resistor Rs to obtain a voltmeter able to measure 5oviul scale5.9kohm6kohm119.9kohim120kohm199 Skohm200kohm499.8kohm

Given data, Full scale current Ifsd=100 μA Internal resistance Ri=200 Ω Voltage to be measured Vm=50…

A sensitive ammeter (micro-ammeter) is used to manufacture an analog DC voltmeter. The ammeter has the characteristics: 100A full-scale indication, internal resistance Rix200ohm. Vmeler Rs RA Merel Viae Calculate the series resistor Rs to obtain a voltmeter able to measure 5ov hull scale 5.9kohm 6kohm 119.9kohm 1120kohm OC

A sensitive ammeter (micro-ammeter) is used to manufacture an analog DC voltmeter. The ammeter has the characteristics: 100A full-scale indication, internal resistance Rix200ohm. Vmeler Rs RA Merel Viae Calculate the series resistor Rs to obtain a voltmeter able to measure 5ov hull scale 5.9kohm 6kohm 119.9kohm 1120kohm OC

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 1PA: Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter...

See similar textbooks

Similar questions

At what height are the telephone outlets in this residence mounted? Give measurement to center. _____
Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load d. a signal light
Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
Three 12-V, 100-A-hr batteries are connected in series. What are the output voltage and A-hr capacity of this connection?
find zener voltage and resistance with given values:capacitor: 470 micro Fresistor: 12 ohmV out: 12V DCI out: 1AV in: 120V AC 60 Hzdiode: 0.7V
Determine the voltage output from a Wheatstone bridge if four active strain gages are used in an initially balanced bridge to measure a strain of 750 µɛ. Assume that a digital voltmeter (Rin = infinity) will be used to measure the output voltage and that Sg =2.01 and the supply voltage is 10 volts. Assume that each gage resistance is 350 ohms. 14.06 mv 7.538 mv 28.12 mv 15.66 mv 3.246 mv
Determine the DC currents (la. lc and I) and dc junction voltages (Var Ver and Vca) la-Blank 1 mA, le-Blank 2 mA, I-Blank 3 mA, Var Blank 4 V, Vcr Blank 5 V and VcB - Blank 6 V Use 2 decimal places. Use the following values. VBB= 3V RB= 5kOhms Rc=232 ohms Vcc =18 V BDC=65
16. An RTD has α0 = 0.0035 /oC at T0= 50o C and Resistance R(T0)= 300 Ω . Determine the resistance at 20oC.
Determine (a) VGS (b) ID (c) VDS (d) VD for the following FET biasing configuration in theFig.Q4(e). Here, VDD is 89v.
Please answer all subpart for like this please Asap...
draw a simple circuit diagram to demonstrate, variation of Finger Adjust Preset 10K (a potentiometer) changing the brightness of an LED. In this case, using an analog I/O A5 as an input for the potentiometer and any of the PWM I/O as the output.
Please answer all subpart I will like it please ASAP for like