A circular flap with a diameter d closes the outflow of water from a tank. The flap rotates around the axis A passing through its centroid, which lay at the depth h. Determine the minimum value of the moment M that has to be applied to the flap to open it. 3 Given: d = 0.20 m h= 0.25 m a = 60° p = 1000 kg/m

A circular flap with a diameter d closes the outflow of water from a tank. The flap rotates around the axis A passing through its centroid, which lay at the depth h. Determine the minimum value of the moment M that has to be applied to the flap to open it. 3 Given: d = 0.20 m h= 0.25 m a = 60° p = 1000 kg/m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.16P: Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020...

See similar textbooks

Similar questions

Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020 (channel with a nominal depth of 10 in., weighing 201b/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88in.2,Ix=78.9in.4, and Iy=2.81in.4. If two of these channels are welded together as shown in Fig. (b), find Ix and Iy for the resulting cross section.
The gate of the figure supports a maximum moment of 180kN-m in the support in a. Determine the height maximum h of water that supports. The width is 2.0m. mass of the gate 1000 kg.
The cross section of a rectangular AB of width 2.5 m hinged along A is shown in the figurebelow. The weight of the gate is 55 kg, and it is used to retain the water at depth 3.3m.Calculate the minimum force R at B to hold the gate.
The gate in the figure supported a maximum moment of 180kN-m at the support at a. Determine the maximum height h of water that it supported. The width is 2.0m. The mass of the gate is 1000 kg.
The rectangular panel, which is 4 m wide, 3 m high block the end of a 3 m deep water channel. The is suspended around a horizontal axis along its upper edge through point B and is prevented from opening by a fixed edge at point C. Determine the force which is exterted on the panel by the ridge as shown in fig.(2).
The 2 m diameter and 3.6 m high cistern tank contains kerosen (s.g. =0.8), glycerin (s.g.=1.6) and water each with 1.2 m depth. The hoops are used to reinforce the tank that is each placed at 0.5 m from the edge. a. Determine the hydrostatic force in the tank. b. Determine the hoop tension at the top. c. Determine the hoop tension at the bottom.
A dam with triangular cross section holds back a body of water. The dam has height h. The dam is made of concrete, which has speci…c gravity 3.1. What is the maximum angle, , for which thedam will not tip over about point O?
The face of a dam adjacent to the water has the shape of an isosceles trapezoid of altitude 20 m, upper base 50 m, and lower base 40 m. Find the total force exerted by the water on the dam when the water is 15 m deep.
The 3-m plank shown in section has a density of 800kg/m3 and is hinged about a horizontal axis through its upper edge O. Calculate the angle assumed by the plank with the horizontal for the level of fresh water shown.
Determine the Joint Force (FR) and location (xcp and ycp) acting on the 0.8 m high and 0.8 m wide triangular door shown in the figure.
Your answer is partially correct. A homogeneous, 4-ft-wide, 9.8 -ft-long rectangular gate weighing800lbis held in place by a horizontal flexible cable as shown in the figure below. Water acts against the gate, which is hinged at point A. Friction in the hinge is negligible, Determine the tension in the cable. AssumeL1=9.8ft,L2=7.2ft, andθ=57∘. Please type answer note write by hend.
The 5-m wide sluice gate “ab” shown, tangent to the vertical wall at “a”, holds back water. The surface of the gate in contact with the water can be taken as part of a cylinder with radius 4 m. a. Determine the horizontal force acting on the curve. b. Determine the total force on the curve. c. Determine the location of the vertical force from pt. “a”.