A circular rod of diameter 8 mm and 300 mm long is subjected to a tensile force 20 kN. Take E = 200kN /mm2 . Find stress, strain and elongation of the bar due to applied load.
Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…
A: Given, a= 2mm, b= 100 mm and G = 25 GPa
Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…
A: Given : Modulus of rigidity = 25 G pa a = 4mm b = 300mm We know that shear stress = shear strain…
Q: A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000 N. If the…
A:
Q: A steel (E = 200 GPa) rod ABC is applied by the axial load as shown in Figure Q2(c). The diameter of…
A:
Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented…
A: Given, Elastic modulus of steel, E=211MPa H1=4cm=0.04mH2=11cm=0.11m R=2×2cmQ=6×6cm…
Q: A steel rod with a cross-sectional area of 0.20 in is stretched between two fixed points. The…
A:
Q: A steel bar of square section is subjected to an axial compressive load of 100 kN. Under this load,…
A:
Q: Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is…
A:
Q: A steel rod placed between two walls is an exact fit and is stress-free at 20 degrees Celsius. Find…
A: The temperature at which the compressive stress becomes 100 MPa is 62.7350 ℃.
Q: Q3) The rigid bar ABCD is supported by bars (1) and (2). After load P is applied, the normal strain…
A: Given that, The strain in bar 1, ε1=20 μm/m, The deflection in bar 1 is, Strain in bar 1 is given…
Q: AB and CD caps of the same material are tightly fitted on both ends of the 24 mm diameter AD steel…
A: Given: E = 200 GPa LAB = 48 mm LBC = 72 mm LCD = 48 mm DAB = 36 mm…
Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…
A: Shear stress : When an external force acts on an object, It undergoes deformation. If the direction…
Q: If Young's modulus of some material is 150 GPa and shear modulus is 50 GPa, find the poisson's ratio…
A: Given, Young's modulus = E = 150 GPa Shear modulus = G = 50 GPa Let us consider, Poisson's ratio…
Q: A circular aluminum tube with a length of L = 420 mm is loaded in compression by forces P (see…
A:
Q: A 4-mm-diameter steel wire, 3.2 m long, carries an axial tensile load P. Find the maximum safe value…
A:
Q: A steel rod of diameter 10 mm carries an axial load of 10 kN. Consider the modulus of elasticity and…
A:
Q: 10. A steel rectangular block, a = 2.4cm wide and b =1.2 cm deep, is subjected to an axial tensile…
A: GIVEN :- Width : a=2.4 cm=0.024 mdepth : b=1.2 cm=0.012 mLength : L=10 cm=0.1 mincrease in length :…
Q: 1. Axial bar loaded as shown in figure. Find the stress, strain and elongation at the tip of the…
A: Given, Length of the bar = L = 40 in Diameter of the bar = d = 1 in Load applied = P = 1000 lb…
Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…
A:
Q: A steel (E = 200 GPa) rod ABC is applied by the axial load as shown in Figure Q2(c). The diameter of…
A:
Q: A rectangular plate 50 mm × 10 mm with a hole 10 mm diameter is subjected to an axial load of 10kN…
A:
Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…
A: given:a=4mmb=300mmG=25GPa
Q: A bar of size 3m long, 250 mm wide and 150 mm thick is subjected to pull of 50 kN. Find change in…
A: Given data as per question Length of bar=3mwidth of bar=250mmthickness=150mmPulling force =50…
Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…
A:
Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented…
A: Given ∆LAC=0.72mmE=223 MPa=223 N/m2=223 ×10-4 N/cm2H1=LAB=7 cmH2=LBC=10 cmArea of bar AB=AAB=2×2=4…
Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…
A:
Q: A material having a shear modulus G, is deformed under a pure shean stress as shown in the following…
A:
Q: A closed thin walled cylindrical vessel has a diameter D of 660 mm, a wall thickness t of 2.0 mm and…
A:
Q: Find the resulting strains in a unidirectional lamina subjected to normal tensile stresses of 20MPA…
A:
Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented…
A:
Q: A 3/4 -in-diameter steel tension rod is 6 ft long and carries a load of 15 kip. Find the tensile…
A: Given data: Diameter of rod = 0.75 inch = 0.01905 m Length of rod = 6 ft = 6 x 12 = 72 inch =…
Q: he beam supports an 80 kg vertical mass applied at D. The beam is pinned to the wall at point A and…
A: Here, BC=15cm×15cm E=70GPa Load at D, FD=80×g=80×9.81N=784.8N Taking moment about point A. ∑MA=0…
Q: A В 3 m Figure Q3(a)
A: (a) To plot the stress strain diagram for elastic-perfectly plastic material. (b) To find P = ?
Q: Calculate the applied shear stress
A: Ans is 1.25Gpa
Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented…
A:
Q: An aluminum specimen shown in Figure has a diameter of d0 = 25 mmand a gage length of L0 = 250 mm.…
A: Given Data Load, P=165000N Original diameter D0=0.025m original length L0=0.250m gauge length…
Q: find the normal strain if the figure is connected by rigid pins. v is poisson's ratio and E is…
A:
Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…
A:
Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…
A:
Q: Strains measured in a, b and c directions are yardımıa=-150x10-6, ɛb=200x10-6, and ɛc=300x10-6 with…
A: Given Data ɛa =-150x10-6 ɛb =200x10-6 ɛc =300x10-6 E=200 GPa Poisson ratio ν= 0.3
Q: 4(a) A solid circular bar is experiencing axial load F=3 kN as in Figure 4(a). Find the strain…
A: Note- As per our guidelines we are supposed to answer only one question. Kindly repost other…
Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…
A: Given, a= 1mm, b= 200mm and G=25GPa
Q: A bronze bar 3 m long with a cross sectional area of 320 mm 2 is placed between two rigid walls. At…
A: Given: Length of bar, L = 3m Area of cross-section; A = 320mm2 Initial temp.; T =20oC Compressive…
Q: A steel bar having 65mm*65mm*3000mm dimension is subjected to an axial force of 128 kN. Taking…
A:
Q: -20kN 8. A steel bar ABCD 4 m long is subjected to force as shown in figure below. Find the…
A: Answer: The total elongation of the bar is 1.7507 mm.
Q: A bar of aluminum alloy of rectangular section75 mm x 20 mm and 800 mm long is stretched by an axial…
A:
Q: Q2: A bar of steel, having a rectangular cross-section of 7.5 cm by 2.5 cm (see figure below),…
A: Given data: Width of bar, w = 7.5 cm. Height of the bar, h = 2.5 cm. Length of the bar, L = 100 cm.…
Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…
A: a= 1 mm b=200 mm G=1.5 GPa
Q: Q1// A hollow shaft of 10mm inside diameter and 5mm thick and 2m long extends by 0.5 cm under a…
A: Write the given values along with the suitable variables.
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 4 images
- A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressureA spherical steel pressure vessel (diameter 500 mm, thickness 10 mm) is coated with brittle lacquer that cracks when the strain reaches 150 X 10~ (see figure). (a) What internal pressure p will cause the lacquer to develop cracks? (Assume E = 205 GPa and v = 0.30.) (b) If the strain is measured at 125 x 10-6, what is the internal pressure at that point?
- A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.
- A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing maching until the applied torque reaches the value T = 500 N ·. At this value of torque, a strain gage oriented at 45º to the axis of the bar gives a reading e = 339 × 10-6. What is the shear modulus G of the material?An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
- A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends. Find i lie maximum shear, ion si le. and compressive stresses in the tube and their corresponding strains. Assume that G = 6000 ksi.A copper rod of length L = 18.0 in. is to be twisted by torques T (see figure) until the angle of rotation between the ends of the rod is 3.0°. (a) If the allowable shear strain in the copper is 0.0006 rad, what is the maximum permissible diameter of the rod? (b) If the rod diameter is 0.5 in., what is the minimum permissible length of the rod?A circular cylindrical steel tank (see figure) contains a volatile fuel under pressure, A strain gage at point A records the longitudinal strain in the tank and transmits this information to a control room. The ultimate shear stress in the wall of the tank is 98 MPa, and a factor of safety of 2,8 is required. (a) At what value of the strain should the operators take action to reduce the pressure in the tank? (Data for the steel are modulus of elasticity E = 210 GPa and Poisson's ratio v = 0.30.) (b) What is the associated strain in the radial direction