Take N= 10 thank you.... ? A circular shape blank will be cut of 100+Nmm diameter from a strip of 2.8+mmwith a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determinea) The appropriate punch diameter.b) Blanking force.Nc) Blanking force when the blade angle is (5+:100Notes:- Never change the template and only write your own identity data.- Your N value is in the list below and is unique to you.- Take at least 3 digits after the decimal point.- Specify the units.- You can use Word Equation or paste your solution on the page(s).- If you are preparing the application homework with your handwriting, be sure to take thephoto with the paper in front view. Terms may not be selected for angled shots.

given diameter of circular blank to be cut, db=101 mmstrip thickness, t=2.9 mmclearnace, C=0.25…

A circular shape blank will be cut of 100+ 10 N mm diameter from a strip of 2.8+ 100 mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine a) The appropriate punch diameter. b) Blanking force. c) Blanking force when the blade angle is 5+ 100,

A circular shape blank will be cut of 100+ 10 N mm diameter from a strip of 2.8+ 100 mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine a) The appropriate punch diameter. b) Blanking force. c) Blanking force when the blade angle is 5+ 100,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Orthogonal cutting, in a machining process,The attacking team sawdust (α) is 10 ̊. operationchip (t0) 0.5 mm and machining beforeAfter the chip coating (tc) is 1,125 mm.Accordingly, in machining;a) Slip plane (ϕ),b) Shear strain (γ) calculator
Suppose you are asked to conduct an experiment to study the impact of three factors(temperature: high vs low, cutting speed: fast vs slow, and tool type: current vs new) on a product. Briefly describe how you would conduct the experiment. Pay attention to the DOE priciples.
A slab milling operation is performed on the top surface of a tool-steel workpiece 450 mm long by 7.5 cm wide. The helical milling cutter, which has an 80 mm diameter and seven teeth, is set up to overhang the width of the part on both sides. Cutting speed is 4000 mm/min, feed is 0.015 cm/tooth, and depth of cut = 0.60 cm. Determine (a) the actual machining time to make one pass across the surface and (b) the maximum metal removal rate during the cut. (c) If an additional approach distance of 0.05 m is added at the beginning of the pass, and an overtravel distance at the end of the pass equal to the cutter radius plus 0.0115 cm, what is the duration of the feed motion
Draw the forces and angles involved in the cutting process and calculate shear angle (Ø), friction coefficient and tangential force ,cutting force = 80 kN, resultant of forces =100KN. friction force=75KN, rake angle =20' undeformed chip thickness = 0.65mm and deformed chip thickness = 0.72mm vjall
A turning operation is made with a rake angle of 10 degrees, a feed of 0.010 in/rev, and a depth of cut = 0.100 in. The shear strength of the work material is known to be 50,000 lb/in2, and the chip thickness ratio after the cut = 0.40. Determine the cutting force and the thrust force. Use the orthogonal cutting model as an approximation of the turning process.
Draw the forces and angles involved in the cutting process and calculate shear angle (0), friction coefficient and tangential force if ,cutting force = 80 kN, resultant of forces =100kN, friction force=75kN, rake angle =20° undeformed chip thickness = 0.65mm and deformed chip thickness = 0.72mm
Give brief explanation within 20 minutes will definitely upvote (handwritten solution acceptable)
We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical milling machine and 50 cm from the edge. The width of the slot is 40 mm. TheDepth of the slot is 25 mm. For this, several rough cutting steps and aFine cut with a depth of 0.20 mm. The depth for each of the steps ofrough cut is limited to 1.75 mmAditional information:What is the number of blades used for the rough cutting steps?What is the number of blades used for the fine cutting step?
A 200 mm long magnesium alloy bar, 63 mm in diameter is turned on a lathe using a high speed steel cutter travelling at 180 mm/min. The spindle rotates at 450 rpm and lathe is equipped with a 10 kW motor, operating at a mechanical efficiency of 92%. The final diameter of the magnesium alloy bar is 59,5 mm. Indicate with a sketch the recommend size and location of the following tool angles: back rake, side rake, end relief, side relief and side and end cutting edge. Calculate the cutting time for the machining process.Calculate the required cutting force.
Find the machining time, in seconds, and the rate of material removing in mmA3;sec for a turning operation having the following information: 1- Wp diameter is 80mm, 2- the length is 0.12m, 3- the cutting speed is 80m/min, 4- feed i50.5 mm/rev and 5- the depth of cut is 0.002m.
A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy = 1200ksi If the width of cut is 0.30 inand the student set a rake angle of 0and a cutting speed of 200fl / min while she assumed a coefficient of friction to be 0.5. What is the maximum depth of cut the student can achieve?
Differentiate between single point, multipoint and form tool and Identify the ten examples of single point, multipoint and form tool.