A circular shock absorber, as shown in the figure below, is designed to support a set of sensitive instruments. The system consists of an aluminium circular bar of diameter d1, a hollow circular rubber insulator acting as shock absorber of diameter d2 and height h, and an aluminium circular tube. The bar and the insulator are glued to each other. The rubber insulator is bonded to the aluminium circular tube. The aluminium circular tube is fixed on the ground. You are given the following inputs: F = 1000 N D1 = 4 mm D2 = 40 mm H = 40 mm G = 600 KPa T = 2 mm Select the best answers from those given below:

A circular shock absorber, as shown in the figure below, is designed to support a set of sensitive instruments. The system consists of an aluminium circular bar of diameter d1, a hollow circular rubber insulator acting as shock absorber of diameter d2 and height h, and an aluminium circular tube. The bar and the insulator are glued to each other. The rubber insulator is bonded to the aluminium circular tube. The aluminium circular tube is fixed on the ground. You are given the following inputs: F = 1000 N D1 = 4 mm D2 = 40 mm H = 40 mm G = 600 KPa T = 2 mm Select the best answers from those given below:

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.12P: A bungee jumper having a mass of 55 kg leaps from a bridge, braking her fall with a long elastic...

See similar textbooks

Similar questions

A bungee jumper having a mass of 55 kg leaps from a bridge, braking her fall with a long elastic shock cord having axial rigidity EA = 2.3 kN (see figure). If the jumpoff point is 60 m above the water, and if it is desired to maintain a clearance of 10 m between the jumper and the water, what length L of cord should be used?
A polyethylene bar having rectangular cross section with a width 7.35 in. and depth 7 in. is placed insidea hollow steel square section with side dimension of8 in. The polyethylene bar is then compressed by an axialforce P. At what value of the force P will the gap betweenthe polyethylene bar and the steel tube be closed for thefirst time on one side? What is the remaining gap betweenthe polyethylene bar and the steel tube on the other side?For polyethylene, assume E 5 200 ksi and n 5 0.4.1
A safety valve (pressure relieve valve) on top of a pressure vessel containing steam under pressure p = 2 MPa, has a discharge hole of diameter d = 10 mm as shown in the figure below. The valve is designed to release the steam when the pressure reaches the maximum allowable value pmax = 2.23 MPa. If the free height (i.e., uncompressed height) of the spring hfree = 135 mm and its spring stiffness k = 5 kN/m, what should be the dimension h of the valve?
The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a construction site on the ocean floor. The plastic panel weighs ( 200 N ) in air and is lowered at a rate of ( 2 m/s ). Assuming the panel remains vertically oriented, calculate the tension force in the cable. Take ( ρ = 1000 kg/m3, ν = 1.31 * 10-6 m2/s ), and use; CDlam = 1.328 / ReL 1/2 CDturb = 0.072 / ReL 1/5 .
A square plastic bar (length LP,side dimension sp=193 mm) is inserted inside a hollow.square cast iron tube (length Le = 400 mm. side sc=200 mm,and thickness tc=3 mm). (A)What is the required initial length L,of the plastic bar so that.ilcn it is compressed by some force the final length of bar and tube are equal to length L and,at the same time, the gap beten plastic bar and cast iron tube is closed? (B) Compare initial and final volumes for the plastic bar. Assume that E = 170 GP E,= 2.1GPa.v = 0.3.and = 0.4.
A fuselage with a perfect circular cross-section with a diameter of 3.6 m and a skin thickness of 1.2 mm. Assume a pressure differential while flying at cruising altitude of 45 kPa. Calculate the circumferential stress induced by the pressure differential
A tall standpipe as shown in Figure Q1(a) with an open top has an inner diameterd = 21 m and wall thickness t = 25 mm, where 1.Given the weight density of water γ = 9.81 kN/m3 and water pressure is p = γ h,calculate the height h of water that will produce a circumferential stress of 12 MPain the wall of the standpipe 2.Calculate the axial stress in the wall of the tank due to the water pressure.
um and steel pipes are fastened to rigid supports at ends s for the following data: The cross:sectional area of aluminum pipe A, = 8.92 in?, cross-sectional area of Stei & modulus of elasticity of aluminum E, = 10 x10° psi, and modulus of elasticity of
A 10 kg axial load is uniformly carried by an aluminum alloy pipe with an outside diameter of 10 cm and an inside diameter of 9.6 cm. The pipe is 1.2 m long, Young's modulus for the aluminum alloy is 75 GPa. How much is the pipe compressed?
A rubber cylinder R of length L and cross sectionalarea A is compressed inside a steel cylinderS by a force F that applies a uniformly distributedpressure to the rubber (see figure).(a) Derive a formula for the lateral pressure pbetween the rubber and the steel. (Disregardfriction between the rubber and the steel, andassume that the steel cylinder is rigid when comparedto the rubber.)(b) Derive a formula for the shortening δ of therubber cylinder.
5. In the CN Railwayproject,steel railroad rails of 9.5meters long are to be installed.If the modulus of elasticity of steel is207GPa, and if the lowest temperature considered is 18°C and a maximum temperature of 36°C is designed for, determine the clearance between the rails such that adjoining will just touch at maximum design temperature. Assume α for steel is 11.6 x 10-6/°C
A length of 18 mm diameter steel wire is coiled to a close helical spring having 9 coils of 72 mm mean diameter, and the spring has a stiffness k. If the same length of wire is coiled to 9 coilsof 54 mm mean diameter, then the spring suffness will be