A coil of inductance 318.3 mH and negligible resistance is connected in series with a 200 resistor to a 240V, 50 Hz supply. Calculate the inductive reactance of the coil, the impedance of the circuit, the current in the circuit, the p.d. across each component, and the circuit phase angle.

A coil of inductance 318.3 mH and negligible resistance is connected in series with a 200 resistor to a 240V, 50 Hz supply. Calculate the inductive reactance of the coil, the impedance of the circuit, the current in the circuit, the p.d. across each component, and the circuit phase angle.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the...

See similar textbooks

Related questions

Q: • 1. Determine Iz using current division. lov (+ 52 N Iz $32 ≥6.2 65 392

A: We need to find out the current by using of current Division rule .

Q: What is the Thévenin equivalent voltage Vth across a and b for the circuit shown in Figure 4.21? 12…

A: The circuit is represented by its equivalent Thevnin's circuit or Norton's circuit. In Thevenin…

Q: 9 A small business operates three pieces of equipment for nine hours continuously per day for six…

Q: Make a ladder diagram for the following: 1. Latching Circuit a. Set Priority b. Reset Priority

A: As per Bartleby guideline we need to answer the first question only. Kindly repost the rest…

Q: Overall efficiency of dc generators is usually of the order of 60 to 70% O 70 to 80% 80 to 90% 85 to…

A: A DC generator transforms mechanical energy into electrical energy. This generator works on the…

Q: Calculate the base transport factor. Assume transistor parameters of xB=0.80 µm and LB=10.0 μm

A: We need to determine the base transport factor. If transistor parameters of xB=0.80 µm and LB=10.0…

Q: A long shunt compound generator has an armature, series field and shunt field resistances of 0.040,…

Q: What is an integrated circuit defined as?

Q: g(t) = 24e-j2nfot 16+ 47² (t - 2)²

Q: A DC generator has eight poles, wound as lap then rewound as a wave, calculate the electrical motive…

A: In this question, DC Generator , Number of pole P= 8, Number of conductors Z= 240 Flux = 0.04wb…

Q: (coso) (17) find the Power factor of the following clf. 452 w mmmm 355 Trizs Iter

Q: At a frequency of 1.5 kHz, the open circuit impedance of the length of the transmission line is…

A: We will find out the characteristics impedance for given transmission line with give open circuit…

Q: Problem: Anso Point charge 15 nc free space. Calculate at PC-213,-1), if you given at the origin of…

A: By using the Electric potential concept

Q: frequency of 1.5 kHz the open circuit impedance of a length of transmission line is 800∠−50◦ and the…

A: We need to find out characteristics impedance for given transmission line for given open circuit and…

Q: Find the average value of the voltage in the figure 5 V hn ov+ O 1.59 V O 63.7 V O6.37 V O 10.5 V

A: In this question, We need to choose the correct option determine the average value of output…

Q: Question 3 A sequential logic circuit with two D flip-flops, two inputs X and Y, and one output Z is…

Q: Energy sources that are being traditionally used for many decades are considered as Non-Conventional…

A: This is a basic problem of types of energy sources. The solution is given in the next step

Q: A lasing cavity is designed to emit light at wavelength around 610nm. If the length of the lasing…

Q: 2. Use the Branch-Current Method (BCM) to solve for ix. (Show all work) R₁ i₁ ww ww R₂ 12 R3 ww R4…

A: We need to find out the current in the given circuit by using of branch current method .

Q: Circle the right answer(s): The energy sources that can provide energy to the world by year 2050 are…

A: Through 2050, fossil fuels will be the main source of energy. This is due to the significant…

Q: On full load a 300V series motor takes 90A and runs at 900 rpm, the armature resistance is 0.10 and…

Q: Given the following nodes from A to G as shown in the diagram, determine the minimum spanning tree…

A: The minimum spanning tree is a subgraph that contains all the given vertices and there should not be…

Q: Given the following nodes from A to G as shown in the diagram, determine the shortest path network…

A: Start from node D and go to the required node Always choose the shortest path

Q: How does capacitive touch function?

A: Solution When another electrical conductor, such as your naked finger, makes touch with this…

Q: Q36. A resistor with a current of 3 A through it converts 500 J of electrical energy to heat energy…

Q: Six equal resistorseach of 10 ohms are connected to form a wye inside a delta. What is the…

Q: Out of the following four sources of losses in a dc generator which one is minimum? O Copper losses…

A: We need to select correct option for losses in dc generator .

Q: d) A section of a home has two rooms connected by a long hallway. Each room has its own light /…

A: Given: Two rooms are connected by a long hallway. Each room has its own light switch. The long…

Q: 16. In a single-phase wattmeter application at full load, the potential transformer phase-angle…

A: It is given that: Phase angle error of potential transformer=γ=-8°Phase angle error of current…

Q: Given Figure shows the input characteristic for an n-p-n silicon transistor. When the base emitter…

Q: Which of the below statements is NOT True regarding Tidal Power? The primary source for Tidal Power…

A: Given: Tidal Energy

Q: following information is given in connection with three loads connected to a 240-V source: load A =…

Q: At a frequency of 1.5 kHz, the open circuit impedance of the length of the transmission line is…

A: Frequency = 1.5 kHz Length of transmission line Zoc = 800∠-50° Ω Short circuit impedance Zsc =…

Q: Tides are generated through a combination of forces exerted by the gravitational pull of: Sun's…

Q: 6S-4 5²-45+16 1- L-1. I need a clear answer by hand, not by keyboard | dybala

Q: Find the current through the load in polar form. E 120 Vrms 60 Hz 30° R1 10Ω L1 150m H L A D R 5002…

A: In this question we need to find a current through load in polar form Let us assume a voltage…

Q: Use mesh analysis to find I₁, I₂ and 13. 1' 15 V +1 I, + Vo§222 4529 12 SA 13 1002 2V0

A: By using of mesh analysis we will find out the mesh current for given circuit

Q: An 8 pole shunt generator has a lap connected armature with 640 conductors. The flux per pole is 50…

A: In this question, We need to determine the speed in rpm of the generator. We know Induced emf in…

Q: 10+ -10- 10- 5- 0 -10- (A) J. 5V 10- F 0 -5- -10+ (B) R1 1k 15+ 10 5+ (C)

A: Option c is correct

Q: A 15 KVA, 2400: 240/120 V, 60 Hz, the two-winding transformer is to be reconnected as a 2400:2520 V…

Q: 5. Find Vo using source transformation. ба 652 W Vo W 50 + 3A 15.2 n + $100 30V ✓7A

Q: explain clearly a common emitter amplifier with voltage divider bias and how it works

A: Here the properties of common emitter amplifier is analysed.

Q: A SW1 B SW2 2 3 6 8 9 12 10 13 or A 0 0 1 1 11 с Logic function: Boolean equation for output, C =…

A: The output of AND gate is high if all the input is high. The output of OR gate is high if any one of…

Q: D Clock B. From a Positive Edge D Flip-flop. Draw the normal and complemented output PC

Q: Example 12.51. A series RLC circuit has R = 5, L=0.2 H and C= 50 uF. The applied voltage is 200 V.…

A: Given, A series RLC circuit with, Resistance, R=5 Ω. Inductance, L=0.2 H. Capacitance, C=50 μF.…

Q: Given the following nodes from A to G as shown in the diagram, determine the shortest path network…

A: Given: A network with nodes A to G. To find: Shortest path network from node E to all other nodes

Q: 4. a. Design a Combinational circuit with three inputs, (A, B, and C) and four outputs, (U, V, W,…

A: This is a basic problem of logic gate function. The detailed solution is given in the next step.

Q: the voltage gain of an amplifier is 250 while the current gain is 100. Compute for the power gain in…

A: Given: For an amplifier, The voltage gain is, Av=250. Current gain, AI=100.

Q: (b) Calculate the resonant frequency of the Band Pass Filter if its bandwidth is 100Hz and Q factor…

A: Given: A bandpass filter has following specifications, Bandwidth, B=100 Hz. Quality factor, Q=500.

Q: Materials whose conductivity falls between those of conductors and insulators are called

A: Introduction - Conductors - The materials that allow electricity to pass through them are known as…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A coil of inductance 318.3 mH and negligible resistance is connected in series with a 200 ohm resistor to a 240V, 50 Hz supply. Calculate the inductive reactance of the coil, the impedance of the circuit, the current in the circuit, the p.d. across each component, and the circuit phase angle.
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage V and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60 Hz, R = 10 R. Vcoil = 22.4 V, VR= 20 V and V = 36 V. find the resistance and inductance of the coil. please use reference photo
a coil of unknown resistance and a reactance of j8 Ohms is in parallel with a pure capacitor of -j16 Ohms reactance.Determine all possible values of coil resistance if the total impedance is 16 Ohms at a power factor of 0.96.\ Answer/s: 6 ohms (if lagging pf) 10.6667 Ohms (if leading pf)
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage Vr and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60 Hz, R = 10 ohms, Vcoil = 22.4 V, Vr = 20 V and V = 36V. Calculate Xl and Xc
A coil has an inductance of 478µH.What is its reactance in 1000Hz ac circuit? 3.00ohms if connected in series with a resistor of 4.00ohms. What is the reactance of a 3.00microfaradcapacitor? What is the impedance of thecapacitor in series of 300ohms? What would be the current if the capacitorand resistor are connected in series with1200V line?
An impedance coil having a resistance of 15 ohms and an inductance of 0.08 henryis connected in series with a variable capacitor. If a 117 volt 60 cps source isconnected to the circuit, what will be the capacitance of the capacitor and the current(a) when the circuit has a power factor of 0.866 leading and (b) when the voltagedrop across the coil is equal to the voltage drop across the capacitor?
An impedance coil takes 144 watts at a lagging power factor of 0.6. What value of capacitanceand resistance should be connected in series with the coil if the power input to the latter is toremain unchanged and the overall power factor is to be unity (in resonance)? The circuit isenergized by a 120 volt, 60 cps source.
A transmission line has a reactance of 1 Pu is operating at Vs = Vr = 1 Pu. The generator is connected at source end which is delivering 0.5 Pu of active power and the transmission line is compensated with a series capacitance of 0.5 Pu. Find the load angle with series capacitance compensation ?
Compute the expected power factor of the circuit given the different capacitance.
In the inductor circuit, if the source voltage, V1, is 8.7∠10° Vp, what would be the voltage in RMS?
1. An impedance coil takes 144 watts at a lagging power factor of 0.6. What value of capacitance and resistance should be connected in series with the coil if the power input to the latter is to remain unchanged and the overall power factor is to be unity (in resonance)? The circuit is energized by a 120 volt, 60 cps source. 2. The given figure is to be designed to pass a wave having a frequency of 3500 cps and block a 2500 cps wave. The series inductor has an inductance of 0.0023 henry. Calculate the capacitance of the series capacitor and the parallel inductor.
For the circuit shown,a) To the coil of a henry, measure its internal resistance and the value of the inductance.b) Measure the effective voltage and current at the terminals of the 100 Ω resistor and at the source.c) Measure the average power delivered by the source.Note the phase shift between the supply voltage and the voltage across the 100 Ω resistor (only at this point).