Answered: A column supports a compressive load of…

A column supports a compressive load of 360KN. Determine the outside diameter of column if inside diameter is 195mm and compressive stress of 90Mpa. ( Ans Do=207.65mm )

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.11P: -11 Determine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base...

See similar textbooks

Related questions

Q: .A link in a packaging machine mechanism has a square cross section of 0.40 in on a side. It is…

Q: Q // If the value of the highest load we get from the tensile test of a wrought iron model with a…

Q: A 12 mm thick steel tire has a width of 110 mm has an internal diameter of 800 mm. Tire is heated…

A: Answer: (a) The tensile stress in the tire is 125 MPa. (b) The compressive pressure between the tire…

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Given: Su = 345 MPa Load, P = 13 kN

Q: For a specific spring where the load applied is 100 N, coil diameter is 4 mm, spring diameter is 20…

Q: If an isotropic material has a shear modulus of 11 Gpa and a Poisson's ratio of 0.34, calculate its…

Q: Question 1. P T. The figure (not drawn to scale) shows a cylindrical column submitted to a combined…

A: as per guidelines i have to solve only first part of your question

Q: 1. Construct a critical end-load intensity against slenderness ratio graph for a range of pinned…

Q: 450-mm-long AISI 1020 steel rod is subjected to a tensile load of 55 kN. The allowable tensile…

A: Given Length = 450 mm Tensile load = 55 kN = 55 X 103 N Allowable tensile stress = 140 MPa = 140…

Q: (1) The belt tension in a 400mm pulley is 4,000N. It is mounted to a shaft to transmit power to…

Q: Figure P3–64 shows two bars of different materials separated by 0.05 mm when the temperature is…

A: Given Gap = 0.50 mm Lb=1.9m La=2.8m Initial Temp = 200C

Q: The diameter of the pin to be used at the B point in the brake mechanism in the figure is dB = 12 mm…

Q: how many times is the system

A: For solution refer below images.

Q: A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a…

A: GIVEN DATA- Pressure P=1.5MPa Internal Dia d=2.5m = 2.5*1000=2500mm Thickness t=40mm Yield stress…

Q: You are in charge of designing a new fixture for a “universal testing machine” that will attach a…

A: The data given is, Maximum load = 30 kN Maximum permissible shear stress, σ = 600 Mpa To…

Q: What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of…

Q: A steel wheel of 900mm diameter on a horizontal steel rail. It carries a load of 50ON. The…

A: GIVEN DATA - W=500N D=900mm SO R=450mm μ=0.1 WE HAVE TO FIND VALUE OF FORCE

Q: circular rod of 50 mm diameter experience a tensile load of 100 N. Find the stress induced in ro

A: Given:Diameter of rod, d=50 mmTensile load, L=100 N

Q: problem 1 pls complete solution

Q: A steel bar carrying 3000kN load,F, is attached to a support by a round pin 0.3m in diameter.…

A: Given data: Applied force (F) = 3000 kN Diameter (d) = 0.3 m Need to determine the shear stress in…

Q: llow structural member manufactured from a high grade tensile strength steel, forms part of a large…

A: as per rule i solved 1st part of question only

Q: A rectangular plate with a hole is shown in fig that carries a tensile load. Stress value calculated…

A: Given that A rectangular plate with a hole is shown in fig that carries a tensile load. Stress…

Q: Rods (1) and (2) were supposed to fit exactly between the rigid walls at A and C, as indicated in…

A: Given DataE1=74 GPaA=1749 mm2L=738 mmE2=204 GPa

Q: 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850…

A: Given: The torque transmitted by shaft, T = 850 lb.in The shaft diameter, d = 1.75 in The ultimate…

Q: An 18mm diameter rivet is used to fasten two 22mm thick plate. If the shearing stress is 60 MPA.…

Q: A 51 mm diameter steel rod (E = 207 GPA) with pinned end conditions is to be subjected to an axail…

A: Given Diameter, d = 51 mm E = 207 GPa Find Maximum length, L

Q: If an isotropic material has a shear modulus of 125 Gpa and a Poisson's ratio of 0.2, calculate its…

Q: The spherical LPG storage tank shown in Figure 3(b) has the following design specifications: Tank…

A: Given data Diameter of spherical tank = 22 mShell plate thickness = 24 mm = 24 x 10-3 mYield stress…

Q: Q3: A part of a bracket in the seat assembly of a bus is shown in Figure (3). The load varies from…

Q: A hollow structural member manufactured from a high grade tensile strength steel, forms part of a…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: A cylindrical metal rod of 20mm diameter and 1m length is subjected to a tensile load of 60KN. To…

Q: What would be the compressive stress in MPa developed in the silica glass furnace tube constrained…

Q: [30] Problem 2: A bracket is designed with a pin-pin horizontal tie rod supporting a boom that is…

A: GivenVertical load P=6kNyield strength σy=400MPadaimeter of the tie rod d=12mmdaimeter of the pin…

Q: A two spring is connected in parallel attached to a single load. The maximum allowable stress is…

A: Given that, Allowable stress, σ=200 MPa,Spring 1, d=33 mm,n=18,R=120 mm,Spring 2,d=30 mm,n=20,R=100…

Q: In the Figure shown below, a machine member is subjected to a vertical orce, Fy varies from (+3P) to…

A: For vertical direction , Wmin=-PWmax=3P F.S=3 σe=255N/mm2 σy=450N/mm2 t=8mm Now,…

Q: A bar is subjected to fluctuating tensile load from 20 kN to 100 kN .The material has yield strength…

A: Given: The fluctuating tensile load in a bar,P1=20 kNP2=100 kNσyt=240 MPaσe=160 MPaFactor of safety,…

Q: The following figure shows the critical position of a crane that supports 2.5 Tons of load by means…

A: (a) Start by calculating the rest of the forces in the crane using equilibrium equations:…

Q: Calculate the design stress when a material has an ultimate strength of 120 psi with a factor of…

A: Answer: The design stress is 165.5 kPa.

Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R, and R₂. The…

A: Given data: ● The load applied on the beam: W = 13 kN ● The diameter of the beam: d = 25 mm ● The…

Q: A mild steel tie-rod has to carry an axial load of 60KN. The maximum permissible stress is 200N/mm2.…

Q: A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of a cast iron 5 mm thick.…

Q: 1.7 The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given, Diameter of wooden post = d = 8 in Length of square concrete footing = L = 12 in Working…

Q: A steel rod on a bridge must be made to withstand a pull of 6000 Ibs. Find the diameter of the rod…

Q: A steel bolt and sleeve assembly are shown in the figure. The nut is tightened up on the tube…

Q: c) A cylinder with external diameter 280mm and internal diameter 200mm is subjected to an internal…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

Write legibly, provide manual step by step solution, and diagram for below given problem.

A column supports a compressive load of 360KN. Determine the outside diameter of column if inside diameter is 195mm and compressive stress of 90Mpa.

(Ans. Do = 20.7.65mm)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 6 ft, 9 ft, 12 ft, and 15 ft. The column has an outside diameter d = 6.625 in. and wall thickness t = 0.280 in, (Assume E = 29,000 ksi and y= 36 ksi.)
-11 Determine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base and free at the top and must support an axial load P = 40 kips (see figure). The column has an outside diameter d = 4.0 in., wall thickness t = 0.226 in., E = 29,000 ksi, and y = 42 ksi.
Select a steel wide-flange column of a nominal depth of 360 mm (W 360 shape) to support an axial load P = 1100 kN (see figure). The column has pinned ends and length L = 6 m. Assume E = 200 GPa and y= 340 MPa. Note: The selection of columns is limited to those listed in Table F-l(b), Appendix F.
A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness ßRat A. Determine the critical load Pcr for the structure.
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A W8 × 28 steel wide-flange column with pinned ends carries an axial load P. What is the maximum permissible length of the column if (a) P = 50 kips, and (b) P = 100 kips? (Assume E = 29,000 ksi and y = 36 ksi.)
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
A wide flange A60 steel column has a length of 4.5meters and pinned ends. If Sx=898x103 mm3, Sy=120x103 mm3, d=358mm, bf=171mm, A=7,159mm2, Fy=414MPa, calculate the design compressive strength in KN of the column. Express your answer in one decimal place.
A unique column has been created with the geometry shown below, where the radius is r = (0.6e-0.08y2) m, the variable y is in meters. The column density of the column material is ρ = 3.21 Mg/m3. Determine the average normal stress at the bottom of the column (y = 0) in units of Pa.
Solve for the indentation diameter if the BHN of the material is 70 and a 500 kg of load is applied? Use indenter diameter 10mm.
A 100-mmmm long rod has a diameter of 15 mmmm. If an axial tensile load of 145 kNkN is applied, determine its change in length. Assume linear-elastic behavior with E� = 200 GPaGPa.
A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine the outside diameter of the tube if the stress is limited to 120 MN/m2