A common measure of transmission for digital data is the baud rate, defined as the number of bits transmitted per second. Generally, transmission is accomplished in packets consisting of a start bit, a byte (8 bits) of information, and a stop bit. Using these facts, answer the following: How many minutes would it take to transmit a 1024 ×1024 image with 256 intensity levels using a 56k baud modem?

A common measure of transmission for digital data is the baud rate, defined as the number of bits transmitted per second. Generally, transmission is accomplished in packets consisting of a start bit, a byte (8 bits) of information, and a stop bit. Using these facts, answer the following: How many minutes would it take to transmit a 1024 ×1024 image with 256 intensity levels using a 56k baud modem?

Operations Research : Applications and Algorithms

4th Edition

ISBN:9780534380588

Author:Wayne L. Winston

Publisher:Wayne L. Winston

Chapter20: Queuing Theory

Section20.10: Exponential Queues In Series And Open Queuing Networks

Problem 8P

See similar textbooks

Similar questions

Suppose, BanglaLink has 4 voice channels, each of 60Mbps. They use synchronous TDM to multiplex these channels. If 3 characters at a time are multiplexed (3 characters in each output slot), I. Draw the first two output frames with arbitrary inputs. II. What is the size of an output frame in bits? III. What is the output frame rate? IV. What is the duration of an output frame? V. What is the output data rate? VI. Input bit duration? VII. Output bit duration? VIII. Output slot duration?
Why is the gap time between bytes vary in asynchronous transmission?
Assume having a low-pass noiseless channel that spans from a Frequency of 0Hz to 130Hz, to send at a bit-rate value that is not less than 1Kbps, then you would at least need ................. signal levels.
Q. 2. (b) Suppose Banglalink has 8 voice channels, each of 80 Mbps. They use synchronous TDM to multiplex these channels. If four characters at a time is multiplexed, answer the following questions i) What is the input slot duration? ii) What is the input bit duration? iii) What is the output slot duration? iv) What is the output bit duration? v) What is the output bit rate? vi) What is the size of an output frame?
Que.a) Consider a CSMA/CD network that transmits data at a rate of 400 x 106 bits per second. The maximum signal propagation time from one node to another node is 20 microseconds. The minimum size of a frame in the network is(. bytes).
88. Suppose transmission rate of a channel is 32 kbps. If there are ‘8’ routes from source to destination and each packet p contains 8000 bits. Total end to end delay in sending packet P is ................ a. 2 sec b. 3 sec c. 4 sec d. 1 sec
Suppose that a sender and a receiver exchange data via UART with followingconfiguration:Baud rate = 115200 bits/s 1 start bit, 2 stop bits, 8 data bits, 1 parity bit 16 clock periods used for sampling 1 bit Answer the following questions please and thank you(a) What is the required clock frequency?(b) Suppose a 48 MHz clock. What is a suitable division factor to generate the neededclock in sub-question (a)?(c) How long does it take to transfer 10 MBytes of data?
Calculate the minimum timeout value for a stop-and-wait algorithm running over a 50-meter point-to-point copper link. Assume a minimum delay of 5 µs at the receiver. If you know the distance between two points, you can calculate the speed-of-light latency, although you have to be careful because light travels across different media at different speeds: It travels at 3.0 × 108 m/s in a vacuum, 2.3 × 108 m/s in a copper cable, and 2.0 × 108 m/s in an optical fiber.
Four channels, two with a bit rate of 120kbps and two with a bit rate of 880kbps, are to be multiplexed using multiple-slot TDM with no synchronization bits.Answer the following questions: a. What is the size of a frame in bits? b. What is the frame rate? c. What is the duration of a frame? d. What is the data rate?
In asynchronous transmission, why does the gap time between bytes differ?
Suppose, BanglaLink has 4 voice channels, each of 60Mbps. They use synchronous TDM to multiplex these channels. If 3 characters at a time are multiplexed (3 characters in each output slot), 1. Draw the first two output frames with arbitrary inputs. 2. What is the size of an output frame in bits? 3. What is the output frame rate? 4. What is the duration of an output frame?
1.) There is a data that has a file size of 26Mb with an ethernet overhead of 8 Mb. Find the Total amount of data to be transferred and Throughput, if there is an amount of data loss of 15 Mbps due to errors and acknowledgments. 2.) Assume that the distance between the sender and the receiver is 5000 km and that light travels at 1.7 x 108 m/s. What is the propagation time and the transmission time for a 1.44 MB message if the bandwidth of the network is 3 Mbps? 3.) An analog signal has a bit rate of 36000 bps and a baud rate of 1200 baud. How many data elements are carried by each signal element? How many signal elements do we need?