A component machined from a plate made of steel (Sut = 630 N/mm²) is shown in the figure. It is subjected to a completely reversed axial force of 55 kN. The factor of safety is 2. The size factor is 0.85. Determine the plate thickness t for infinite life, if the notch sensitivity factor is 0.8.

A component machined from a plate made of steel (Sut = 630 N/mm²) is shown in the figure. It is subjected to a completely reversed axial force of 55 kN. The factor of safety is 2. The size factor is 0.85. Determine the plate thickness t for infinite life, if the notch sensitivity factor is 0.8.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A plate made of steel 20C8 (Sut = 440 N/mm2 ) in hot rolled and normalized condition is shown in Fig. It is subjected to a completely reversed load of 30 kN. The notch sensitivity factor q can be taken as 0.8 and the expected reliability is 90%. The size factor is 0.85. The factor of safety is 2. Determine the plate thickness for infinite life. (V. B. Bhandari Example 5.3)
An axle is welded to the wall as shown in the figure.Other data:- The diameters D1 = 45 mm, D2 = 50 mm, D3 = 55 mm- The radii R1 = 3 mm, R2 = 2.5 mm- The notch sensitivity factor η = 0.5How big is the maximum tension in the axle and where does it occur?
At a temperature of 60°F, a 0.05-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 2.9 in. and a thickness of 0.80 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.80 in. The supports at A and C are rigid. Assume h1=2.9 in., h2=1.9 in., L1=28 in., L2=42 in., and Δ=Δ= 0.05 in. Determine(a) the lowest temperature at which the two bars contact each other.(b) the normal stress in the two bars at a temperature of 255°F.(c) the normal strain in the two bars at 255°F.(d) the change in width of the aluminum bar at a temperature of 255°F. Determine the lowest temperature, Tcontact, at which the two bars contact each other.
The notched bar shown in the following figure is subjected to an axial load P that varies between -50 kN and 20 kN. The fatigue stress concentration factor at the notch is ke = kfm = 2.1. The bar is made of steel (Sut = 324 MPa). Its corrected endurance limit is Se = 162 MPa. Determine the infinite lifetime fatigue factor of safety (using Case 3 safety factor calculation). r= 3 mm 36 mm 30 mm 30 mm P. r= 3 mm Select one: O a. Nf = 4.63 O b. Nf = 3.47 O c. N = 2.52 O d. Nf = 1.63
At a temperature of 60°F, a 0.03-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.70 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.70 in. The supports at A and C are rigid. Assume h1=3.0 in., h2=1.9 in., L1=27 in., L2=47 in., and Δ=Δ= 0.03 in. Determine(a) the lowest temperature at which the two bars contact each other.(b) the normal stress in the two bars at a temperature of 260°F.(c) the normal strain in the two bars at 260°F.(d) the change in width of the aluminum bar at a temperature of 260°F.
At a temperature of 60°F, a 0.03-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.70 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.70 in. The supports at A and C are rigid. Assume h1=3.0 in., h2=1.9 in., L1=27 in., L2=47 in., and Δ=Δ= 0.03 in. Determine:
The shaft in the figure is mounted with a gear wheel key. Shaft material 42CrMo4 The weight of the gear on the shaft is 0.9 kg, dimension, surface and notch factors KbK / Kç = 0.83, shaft speed n = 1120 rpm, shaft transmitted power 7.5 kW, force on shaft Fn = F = 2680 N Since the desired safety coefficient is Ssafe = 2; Check the safety of the shaft
A stepped shaft whose made of SAE 1117 steel has an ultimate strength of 69.7 ksi. The notch sensitivity factor is 0.983 and 0.00435 is the constant dependent upon the ultimate strength. Check the radius of the stress raiser.
A 0.5-in.-diameter steel [E= 30,000 ksi] bolt (1) is placed in a copper tube (2). The copper [E= 16,000 ksi] tube has an outside diameter of 1.00 in., a wall thickness of 0.125 in., and a length of L= 8.0 in. Rigid washers, each with a thickness of t= 0.125 in., cap the ends of the copper tube. The bolt has 20 threads per inch. This means that each time the nut is turned one complete revolution, the nut advances 0.05 in. (i.e., 1/20 in.). The nut is hand-tightened on the bolt until the bolt, nut, washers, and tube are just snug, meaning that all slack has been removed from the assembly but no stress has yet been induced. What stresses are produced in the bolt and in the tube if the nut is tightened an additional quarter turn past the snug-tight condition?
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14
A steel pipe has an inside diameter of d = 350 mm and an outside diameter of D = 158 mm. The length of the pipe is L = 5.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter - ____ mm Inside diameter - ____ mm Lenght - ____ mm standard coefficient of thermal expansion steel: 11.25x10^-6/degrees
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm objects falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie: 1. The minimum wire diameter is most nearly A. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in 2. The mean coil diameter is most nearly A. 8.6 in B. 10 in C. 13 in D. 16 in 3. The number of active coils is most nearly A. 8 B. 11 C. 12 D. 14