A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given Es= 2 x 105 N/mm and Ec= 1.2 x 105 N/mm2

A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given Es= 2 x 105 N/mm and Ec= 1.2 x 105 N/mm2

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.3P: Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
the solid circular shaft rod has an original diameter of 20mm. when the load of 50kN is applied the shaft stretches 1.4mm and it has a Poisson's ratio of 0.25. Calculate the change in diameter of the shaft?Assume shaft is in the elastic region.
A hollow steel (E= 30,000ksi) tube (1) with an outside diameter of 2.75in. and a wall thickness of 0.25in. is fastened to a solid aluminum (E= 10,000 ksi) rod (2) that has a 2in. diameter and a solid 1.375in. diameter aluminum rod (3). The bar is loaded as shown in the figure. Determine (a) the change in length of steel tube (1); (b) the deflection of joint D with respect to the fixed support A. (c) the maximum normal stress in the entire axial assembly.
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of the external diameter of 3.6 cm and an internal diameter of 2 cm. The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.5 cm from the neutral axis Solution: (i) The moment of inertia = Answer and unit for part 1 ii) The radius of curvature is Answer and unit for part 2 (iii) The maximum bending stress is Answer and unit for part 3 iv) The bending stress at the point 0.5 cm from the neutral axis is
A steel column of hollow circular cross section is supported on a circular, steel base plate and a concrete pedestal (see figure). The column has an outside diameter d = 250 mm and supports a load P - 750 kN. (a) If the allowable stress in the column is 55 MPa, what is the minimum required thickness? Based upon your result, select a thickness for the column, (Select a thickness that is an even integer, such as 10, 1 14,.. ., in units of millimeters.) (b) If the allowable bearing stress on the concrete pedestal is 15 MPa, what is the minimum required diameter D of the base plate if it is designed for the allowable load Pallow that the column with the selected thickness can support.
STRENGTH OF MATERIALS (NO LONG EXPLANATION NEEDED) PLEASE WITH FBD! RATE WILL BE GIVEN For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to load P = 40 kN. The rods are identical except for their lengths. Find the (a) stress in rod A if its cross-sectional is 300mm2 (b) If rod A elongates by 2mm, how much is the elongation of rod B?
A rod of diameter 50 cm and length 6 m is hanging vertically and carries an axial loadof 10 kN at bottom end. Calculate the elongation of the bar at a distance 2 m from thebottom end. Take the unit weight of the rod material is 25 kN/m' and modulus ofelasticity of the material is 3x109 MPa.
A steel rod 3.0 m long has a cross-sectional area of 0.40 cm2. The rod is now hung by one end from a support structure, and a 600 kg weight is hung from the rod’s lower end. Given g = 9.8 ms-2. Calculate the stress of the rod.
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi, α= 2.9 × 10−6 /°F] bar (1) and an aluminum alloy [E = 10,000 ksi, α= 12.5 × 10−6 /°F] bar (2), below. Each bar has a cross-sectional area of 2.00 in.2 . The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 26 kips is applied and the temperature is increased to 100°F, determine: (a) the normal stresses in bars (1) and (2). (b) the vertical deflection of joint D.
A rectangular steel block 250 mmx100 mmx80mm is subjected to axial loads as follows. 480 kN (tensile in direction of its length) 900 kN (tensile on 250mm x 80 mm faces) 1000kN (comp. on 250mm x100mm faces) taking E=200 GN/m2 and 1/m=0.25 find a). Change in dimensions (height, width and length) b). Change in volume of the block c). Volumetric Strain c). Values of N and K (Module of Rigidity and Bulk Modulus) for material of the block. d). Determine the volume difference if the temperature of block increased by 20K. (Take alpha steel = 11.7 x 10-6 / 0C ) e). Discuss the behavioral characteristic for given application Comparing the impact from given mechanical loadings and thermal loadings to the block.
Determine the average normal stress in each rod if T2=400∘F Calculate the new length of the aluminum segment.
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; α = 2.9 × 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; α = 12.5 × 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.2. The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 36 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1).