A concrete beam is carrying a uniform load on a simple span of 10 meters. If the allowable stresses are fc = 6MPA, fs = 124 MPa and n = 15, what uniform load can the beam carry besides its own weight? 450 mm 450 NA 740 900 740-X 820-X 4-20 mm 80 4- 28 mm 80 Mox. M Moment Diagram

A concrete beam is carrying a uniform load on a simple span of 10 meters. If the allowable stresses are fc = 6MPA, fs = 124 MPa and n = 15, what uniform load can the beam carry besides its own weight? 450 mm 450 NA 740 900 740-X 820-X 4-20 mm 80 4- 28 mm 80 Mox. M Moment Diagram

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: in Baguio. The structure shall be a reinforced concrete building (no shear walls). The weight per…

Q: 2. For the reinforced concrete beam shown in Figure (2), maximum bending moment (80 kN.m), Modulus…

A: The bending moment is M=80 kNm. The elastic modulus of concrete is Ec=20 GPa. The elastic modulus of…

Q: A tied column 300 x 350 mm as shown in the figure is reinforced with 6 pieces steel bars having fy =…

A: Answer : We are given b = 300 mm h = 350 mm f'c = 21 Mpa fy = 414 Mpa Factored load Pu = 1200 KN…

Q: PROBLEM 1] The cantilever beam shown below has the cross-section on the right portion. If the…

Q: A 5 m simply supported beam supports a uniformly distributed load equal to 40 kN/m applied…

Q: A solid circular steel column is to be design to carry an axial load of 620 kN. If the allowable…

Q: A steel beam having a simple span of 8 m. is subjected to a clockwise moment M at the left end and…

A: Fy = 248 MPart = 0.053 md = 0.533 mbf = 0.210 mtf = 0.016 msx = 0.00206 m3 Asked: Maximum…

Q: The floor system of a residential building (LL=1.9KPa) consists of 125mm thick reinforced concrete…

Q: For the simply supported beam shown below, determine the internal resultant loadings at a point 1…

Q: A reinforced concrete beam has a width of 300 mm and a total depth of 500 mm. It is reinforced with…

Q: Q1) A uniform T-section beam is 100 mm wide and 150 mm deep with a flange thickness of 25mm and a…

A: Solution;

Q: Question 7 A 6m x 6m square floor consists of 6 steel beams of mass 15 kg/m and length 6m, with a…

Q: The beam with cross-section shown carries a uniformly distributed load of intensity w over its…

A: Given, There is a two side overhang beam given in the question. Total length of the beam = 4.5m…

Q: Find the span of the beam for the given beam-loading condition. Details of loading and beam is shown…

Q: A cantilever beam has a span of 4 m and carries a uniformly distributed load throughout its span.…

Q: A cantilever beam has a span of 4 m and carries a uniformly distributed load throughout its span. r₁…

A: Bending stress An object frequently suffers bending stress when it is subjected to a significant…

Q: Q1) A uniform T-section beam is 50 mm wide and 100 mm deep with a flange thickness of 25mm and a web…

A: Question is based on the T beam subjected to uniformly varying load . Magnitude of load , dimension…

Q: The beam with cross-section shown carries a uniformly distributed load of intensity w over its…

Q: A square precast concrete slab is lifted by a tower crane by hooking 4 cables at each corner, as…

Q: nj. A beam is 10.5 m in length and loaded as shown in Figure Q4. If the deflection in the…

Q: A simple beam is loaded with a dead load, live load and axial load as shown in the Figure below.…

A: Given beam is simply supported beam and the data is: Ultimate Bending moment=400 Kn-m Ultimate shear…

Q: Q1, A square reinforced concrete slab of dimensions (a x a) m with fixed supported on all edges,…

A: A square slab having size a x a. Maximum poitive moment = 25 kN.m Maximum Negative moment = 40 kN.m…

Q: The figure below shows the cross-section of a concrete column, encased in 8.2mm thick steel. The…

Q: The hollow rectangular cross-sectioned beam (200 mm wide and 400 mm deep with 10 mm thickness) shown…

Q: 4. A 10 m span simply supported beam carries a uniform load. The beam has an adequate lateral…

Q: A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The…

Q: Determine the maximum flexural stresses in the Tee Beam (Fig. 5) and the locations where it occurs.…

Q: 2. A simply supported rectangular beam, 2 in wide by 4 in deep, carries a uniformly distributed load…

A: Given data Width of beam = 2 inch Depth = 4 inch Uniformly distributed load = 80 lb/ft Flexure…

Q: A concrete beam prestressed with a parabolic tendon is shown in the sketch. The eccentricity of the…

Q: We have simply supported two-way slap as shown below. If the density of concrete is 2450 kg/m3,…

Q: A timber block 200 mm by 200 mm is reinforced on each side by steel plate 200 mm by 10 mm thick. It…

Q: A concrete beam has a cross sectional area of 275mm width and 150mm height for the upper flange.…

Q: A reinforced concrete beam has a width of 300 mm and a total depth of 500 mm. It is reinforced with…

A: Given Data: fy=414.7 Mpa fc'=27.1 Mpa Es=200,000 Mpa It is asked to compute depth of compression…

Q: A uniform T-section beam is 100 mm wide and 150 mm deep with a flange thickness of 25 mm and a web…

Q: 13/13 FOR THE RIGID BEAM SHOWN BELOW FIND THE STRESS IN ALUMNUM ROD Steel Rod Est= 200 kN/mm2² A…

A: Free body diagram of given structure is as follows.

Q: The floor system of a residential building consists of 125mm thick reinforced concrete slab (unit…

A: Thickness of slab (t) = 125 mm unit weight of concrete (¥) = 23.6 kn/m3 span of each beam = 8 m…

Q: The shear diagram for a beam is given below. 30 kN 25 kN -10 kN - 20 kN T3ーt te m- 2.5 m: What is…

Q: A simply supported beam of span 4 m carries a concentrated load Pin kN acting downward at distance…

Q: A floor sheathing is supported by 100 mm x 250 mm wooden joists spaced at 600 mm on centers with an…

Q: In a plate girder subjected to a bending moment of 200 kN-m, the width and thickness of flange are…

A: Given- Bending moment M=200 kN-mwidth b=200 mmthickness t=10 mmfy=250 MPa

Q: A simply supported timber beam with length L = 8 m carries a uniformly distributed load w = 13 kN/m.…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Determine the moment capacity of the beam shown in the figure. fe = 28 MPa fy = 414 MPa d, = 20mm…

Q: Calculate the maximum shear stress Tmax in a simply supported wood beam carrying a uniform load of…

A: Given data : Length (L)=1.75 m w=18 KN/m Width (B)=150 mm Height (H)=250 mm

Q: A steel beam having a simple span of 8 m is subjected to a counterclockwise moment at the left end…

A: Given values: Span ,L = 8 m bf=0.210 m Sx=0.00206 m3 d=0.533 m rt=0.053 m tf= 0.016 m Fy= 248 MPa

Q: th straight tendons situated 56 mm above the bottom of the beam under a prestressing force of 671…

A: Data given width =262mmd = 388 mm l = 9.76m wt = 18.61 KN F = 671 KN 56 m above E = 15,679.2…

Q: A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The…

Q: The column shown below carries a factored load Pu = 1000 kN, Mu = 224 kN. The frame is braced…

A: b=d=450 mmPu=1000 kNMu=224 kN.mk=1Cm=1βd=0.20f'c=21 MPafy=276 MPa

Q: 10 A rectangular beam 200mm deep and 300mm wide is simply supported over a span of 8m. What…

Q: 1) Determine the minimum height h of the beam shown in the figure if the flexural stress is not to…

A: Taking moment about C ∑MB = 0RA12-9008+ 4006 - 60×1222 + 60×622 = 0RA = 670 lb.∑Fy = 0 RA+ RB =…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

A concrete beam is carrying a uniform load on a simple span of 10 meters. If the allowable stresses are fc = 6MPA, fs = 124
MPa and n = 15, what uniform load can the beam carry besides its own weight?
450 mm
450
de
NA
740
900
740-X
e20-x
4-20 mm
80
4- 28 mm
80
Mox. M=
Moment Diagram

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A uniform T-section beam is 100 mm wide and 150 mm deep with a flange thickness of 25 mm and a web thickness of 12 mm. If the limiting bending stresses for the material of the beam are 80 MN/m2 in compression and 160 MN/m2 in tension, compute the second moment of area. 110.4 mm 111.4 mm 109.4 mm 108.4 mm
Compute the bending stresses in the beam shown, f'c = 28 MPa Es=200000MPa M=165 kN-m
The main beam of UB 610 x 229 x 101 kg/m in steel grade S275 supportssecondary beamsof UB 406 x 140 x 39 kg/mon its top flange.The schematic diagram of the floor supported by the beams is presented in Figure 1. b)The slab floor is reinforced concrete 150 mm thickwith 50 mm screed on top of it. The slab floor carriesthe uniform distributed load of 400 kg/m2.Calculate the ULS load on the secondary beam. 4xxx= 4715 1xxx= 1715 50xx= 5015
The cantilever beam above is made up of concrete with E = 70 MPa, refer to the table below for the properties and loads for the beam: Given: b(mm) = 250 h(mm) = 400 w(kN/m) = 15 Mb(kN-m) = 45 Using area moment method, determine the following: 1. Vertical reaction at A, RA. 2. Moment reaction at A, MA. 3. Flexural rigidity of the beam in N-mm^2 4. Rotation at B, in degrees. 5. Rotation at C. in degrees. 6. Deflection at B in mm. 7. Maximum deflection of the beam in mm. 8. If a concentrated load will be placed at B to remove the deflection at C, determine the magnitude of this load in kN.
Determine the maximum tensile stress and maximum compressive stress due to the load P acting on the simple beam AB (see figure). Data are as follows: P= 5.4 kN L=3.0 m d=1.2 m b=75 mm t_=25 mm h=100 mm h1=75 mm c1=62.5 mm c2=37.5 mm, and l= 3.3203x10⁶ mm⁴
A beam having a span of 4m is subjected to a maximum shear of 20 kN. It has a triangular cross - section having a base width of 140 mm and an altitude of 300 mm. Which of the following gives the maximum shearing stress developed on the beam? a. 1.43 MPa b. 1.80 MPa c. 1.62 MPa d. 1.78 MPa
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of the whole structure which is 77 lbs per ft. FN= 87 OR 87X10 = 870
Completely solve and box the final answer. Write legibly 1. A built up wooden beam is made up of two 50 mm by 150 mm sections glued on the lower sides of a 100 mm by 250 mm section. Calculate the maximum bending stress if the 6 m simple beam is loaded with 2.8 kN/m.
A 150mm x 25mm wooden beam is reinforced with two 10mm thick steel plates on the top and bottom faces. Determine the width that the plates must have if the beam supports a moment of 50 kn.m and the allowable stresses are 8 Mpa and 100 Mpa, in the wood and steel, respectively. Consider a modular ratio of 15
1. A beam with a W360x45 section (Beam weight 45 kg) is used as a cantilever beam 7.5 m long. Find the maximum uniformly distributed load which can be applied over the entire length of the beam in N/mm, in addition to the weight of the beam, if the flexural stress is not to exceed 140 MPa.(Answer in 2 decimal places)
Calculate and illustrate the magnitude loading in kN/m acting at beam CF. Thank you
The floor system of a residential building consists of 125mm thick reinforced concrete slab (unit weight =23.6KN/m^3) resting on the three 8m spanned RC floor beams spaced at 3.3 meters on center. Size of RC beam is 200mm x 450mm. NSCP load factors: 1.2DL & 1.6LL. Assume simple supports. Calculate the unfactored slab load in KN/m? express your answer in 1 decimal place.