A conditioned room with partial recirculation of room air is to be maintained at 24°C DB, 17°C WB. The local outside environment conditions are 35°C DB, 26°C WB. The sensible heat load is 48 kW. The latent heat load from occupants and infiltration, but excluding ventilation, is 57 kW. Based on the occupancy, 36 cmm of ventilation air is required. Find: (a) the temperature of air entering the room, (b) the volume of air passing through the room, (c) the state of air entering the conditioner, (d) the required ADP, and (e) the system BPF.

A conditioned room with partial recirculation of room air is to be maintained at 24°C DB, 17°C WB. The local outside environment conditions are 35°C DB, 26°C WB. The sensible heat load is 48 kW. The latent heat load from occupants and infiltration, but excluding ventilation, is 57 kW. Based on the occupancy, 36 cmm of ventilation air is required. Find: (a) the temperature of air entering the room, (b) the volume of air passing through the room, (c) the state of air entering the conditioner, (d) the required ADP, and (e) the system BPF.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ammonia in a large container overheats to 14 bar, 300°C, due to a failure. At this state, a small crack opens in the container that acts as a nozzle. The outside environment is at 1 bar, 25°C, and the mass flow rate of Ammonia is 10 g/s . Assume negligible nozzle inlet velocity and adiabatic reversible flow. What is the exit velocity, and the exit cross section?
. A simple open cycle gas turbine plant works between the pressures of 1 bar and 6 bar and temperatures of 300 K and 1023 K. The calorific value of the fuelused is 42 MJ/kg. Find :1. Airfuel Ratio2. Thermal efficiency of the plant if the mechanical and generatingefficiencies are 95% and 97% respectively.Assume air flow = 20 kg/s and compression and expansion are isentropic.
A factory uses superheated steam (P = 15 bar, T = 250 oC) for heating purposes of 20,000 tons/month. Steam is made in a boiler-furnace using 2 (two) types of fuel, namely coal fuel (LHV = 5500 kcal/kg) and heavy fuel oil (137129 Btu/ft3, density = 0.98 m3/kg) Question: a. How much coal fuel is needed to produce steam with the above specifications if the overall efficiency of the system (boiler-furnace = 75%)! b. How much heavy fuel oil is needed to produce steam with the above specifications (boiler-furnace = 75%)! answer every month... Help pleasee.. fast please
Provide a complete given and computation. Include all the decimals. There are received 68,000 kg/h of steam by an ideal regenerated engine, having only one heater, of which the heater receives 15,400 kg/hr the condenser receives the remainder at 0.007 MPa. If the heater pressure is 0.96 MPa, find the state (quality or "SH) of the steam (a) at the heater entrance and (b) at the condenser entrance.
A diesel power plant uses fuel with heating value of 45, 038.8 KJ/kg . What is the density of fuel used at 30°C ?
Thermodynamics The actual cycle of a 5T diesel engine, with a displacement of 7000 cm³ , 2,400 rpm is approximate to the theoretical cycle represented in the figure below, in which the custom rectangle has the area of the same cycle. A compression ratio is 17 and the thermal efficiency is 0.597 when 26.3% of the heat is provided isochorically. It is adopted that the active liquid has ϒ = 1.35 and R = 240J / KgK. To determine a) The values of p T and v at the main points of the cycle; b) The power of the cycle. c) Expansion work.
Steam at 100 bar, 625 C is received by a rankine engine and exhaust at 2 bar. (a) For an ideal engine, find work, steam rate, thermal efficiency and. (b) for actual engine, brake engine efficiency is 85% and generator efficiency is 94%. The driven generator produces 30 MW. Find combined work, combined thermal efficiency, actual exhaust enthalpy, mass flow rate of steam.
Steam enters the steam-generating unit at a pressure of 20 bar and dryness of 0.96 and leaves at the same pressure at a temperature of 350°C. Mass flow rate of steam is 5 kg/s. Find the percentage increase in volume (%) due to drying and superheating.
A diesel power plant uses fuel with heating value of 45,325 kJ/kg. What is the density of the fuel at 40°C?
please written solution by hand and how can com h6 and s6 when T turbine inlet = 130 C , P heat exchanger = 20 bar , P condenser = 5 bar , Tw . cond out = 25 C Tw cond in = 17.5 C efficiencies compressor = 67.5 efficiencies turbine = 78 m. refrig =0.4 kg/s
A performance test of an ice plant gave the following data: Capacity: 20 tons of ice/day Refrigerant: Ammonia Condenser pressure: 1391.5 kPa Evaporator pressure: 208.26 kPa Raw water temperature: 32OC Harvest temperature: -7OC Block of ice: 300 lb/block The compressor is twin-cylinder, single acting, D/L = 1.25, 450 rpm, mechanical efficiency is 80%. Additional heat load due to infiltration and conduction is 20%. Determine: a) Number of cans needed b) Product cooling load c) Refrigerating capacity in tons of refrigeration d) Amount of refrigerant flow e) Size of motor to drive the compressor f) Bore diameter and length of stroke
Steam at 10 bar, 600°C, 50 m/s enters aninsulated turbine operating at steadystate and exits at 0.35 bar, 100 m/s. Thework developed per kg of steam flowingis claimed to be (a) 1000 kJ/kg, (b) 500kJ/kg. Can either claim be correct?Explain.