A controlled full-wave bridge rectifier of Fig. 2 has a source of 100 V rms at 60 Hz, R = 20 2, L = 20 mH, and f= 60HZ, B = 3.7 rad, R v, (or) = Vm sin(or) a=1.1 rad . Determine (a) an expression for load current, (b) the average load current, and (c) the power absorbed by the load. ww

A controlled full-wave bridge rectifier of Fig. 2 has a source of 100 V rms at 60 Hz, R = 20 2, L = 20 mH, and f= 60HZ, B = 3.7 rad, R v, (or) = Vm sin(or) a=1.1 rad . Determine (a) an expression for load current, (b) the average load current, and (c) the power absorbed by the load. ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A conductor carries a current that maybe regarded as equivalent to the sum of two components, one of them being a continuous direct current of 4.2 amp and the other a superimposed half-wave rectifier current. If the latter has a maximum value of 8.3 amp, calculate the average current in the wire if (a) both components have the same direction, (b) the two components are oppositely directed?
A conductor carries a current that may be regarded as equivalent to the sum of two components, one of them being a continuous direct current of 4.2 amp and the other a superimposed full-wave rectifier current. If the latter has a maximum value of 6.4 amp, calculate the average current in the wire if (a) both components have the same direction, (b) the two components are oppositely directed?
2. A certain zener diode has a maximum power rating of 300 mW at 40 deg Cand a derating factor of 1.4mW/deg C. Determine the maximum power the zener can dissipate at a temperature of 80 deg C. 3. From the datasheet, a 1N4728A zener diode has a ZZ of 10 0. The datasheet gives VZ = 3.3 V at a test current, IZ, of 76 mA. What is the voltage across the zener terminals when the current is 90 mA? When the current is 45 mA?
A group of UTAS-Nizwa students are working on a project entitled "Gas leak detector alarm" for their final year in Diploma level. The circuit works on DC voltage of 16 volts and DC current of 7 milliampere. Students need to design a power supply circuit for their project. Consider an RMS voltage input of 220 volt, 60 Hz. Using a Full Wave Bridge Rectifier with Transformer, Silicon diode and Capacitor Filter, Design the power supply. a. Compute for the load resistance, peak output voltage, input peak voltage to the diodes (secondary voltage), peak input voltage and the turns ratio of the transformer. 1. What is the value of the load resistance? b. Draw the Power Supply circuit (capacitor filter connected in parallel with the resistor) and write the computed values (No value for the capacitor).
Fig. 2 shows a single-phase fully controlled rectifier driving a heating element that has a resistance of 10 Ω. The supply voltage, Vs, is 230 Vac at 50 Hz and αf = 30 degrees. Answer the following: Draw a fully labelled waveform diagram showing the output voltage and current with respect to the Vs and the firing angle, αf. Use the waveform to develop an expression for the average output current and voltage Use this expression to calculate the average output current and voltage. What changes (if any) would be observed in Vo if the source Vs was taken from a transformer with a very high inductance?
In Fig. 2 shows a single-phase fully controlled rectifier driving a heating element that has a resistance of 10 Ω. The supply voltage, Vs, is 230 Vac at 50 Hz and alpha(a) f = 30 degrees. Answer the following: Draw a fully labelled waveform diagram showing the output voltage and current with respect to the Vs and the firing angle, αf. [5 marks] Use the waveform to develop an expression for the average output current and voltage [10 marks] Use this expression to calculate the average output current and voltage. [5 marks] What changes (if any) would be observed in Vo if the source Vs was taken from a transformer with a very high inductance?
A 23-V, 50 Hz, 1-ph supply is feeding the following loads which are connected across it.(i) A motor load of 4 kW, 0.8 lagging p.f. (ii) A rectifier of 3 kW at 0.6 leading p.f.(ii) A lighter-load of 10 kVA at unity p.f. (iv) A pure capacitive load of 8 kVA Determine te capacitance of the capacitor at (a) pf = 0.92 lagging (b) pf = 0.95 leading (c) pf = unity
Provide a complete solution 1.) A full-wave rectifier (operating from a 60-Hz supply) drives a capacitor-filter circuit (C = 100 uF), which develops 12 V dc when connected to a 2.5-kiloOhms load. Calculate the output voltage ripple. (answer= 0.12 V rms) 2.)A full-wave rectifier operating from the 60-Hz ac supply produces a 20-V peak rectified voltage. If a 200-uF capacitor is used, calculate the ripple at a load of 120mA
Power Electronics. In the Buck-Boost DC-DC converter circuit:Welding voltage [40-80]VSwitching frequency (f) 25khzVoltage between load terminals 55VCapacitance value 470uFLoad current value [10-25]A Under these conditions, which is the lowest ripple (delta IL) amount of the current passing through the coil (L) in Amps for the lowest L inductance value that can keep the DC-DC converter in a continuous current state? A) 23.9803B) 118.75C) 84.3750D) 47.5E) 59.9507F) 33.75
2. An AC voltmeter uses a bridge rectifier with silicon diodes and a PMMC instrument with FSD = 75 µA. If the meter coil resistance is 900 Q and the multiplier resistor is 708 k2, calculate the applied rms voltmeter when the voltmeter indicates FSD.
Design rectifier circuits to provide an output of100 VDC using a.) HWR b.) Center-tappedFWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply
According to the circuit given in the figure, VT=25mV, |VBE|=0.7V, R1=1487.51Kohm, R2= 7.42Kohm, R3= 6.71Kohm , R4= 2.87Kohm, VCC= 13.00V, VEE= 1.00V , VA=28.21V , Beta= 120.00 , Rs= 36.18ohm, Ry= 15.61Kohm Calculate the IC current, Ri, R0 and voltage gain(V0/V1) according to the source by performing a complete analysis. When performing your operations, 2 steps will be taken after the point. choose the closest one from the stylish ones according to the +/-10% margin of error. There is only 1 correct answer to the question.