The single-phase bridge rectifier of Fig. 5 has an RL Load and an ac source, with R = 102 and L = 10mH. The peak value of the source is Vm = 100V at 60 Hz. The expressions of voltage and current outputs are: (a) Determine vo(t) and io(t) with two ac terms (n=2 and 4) (b) Determine the power absorbed by the load. (c) Consider the simulation of this system and record the Votage and current inputs and outputs

The single-phase bridge rectifier of Fig. 5 has an RL Load and an ac source, with R = 102 and L = 10mH. The peak value of the source is Vm = 100V at 60 Hz. The expressions of voltage and current outputs are: (a) Determine vo(t) and io(t) with two ac terms (n=2 and 4) (b) Determine the power absorbed by the load. (c) Consider the simulation of this system and record the Votage and current inputs and outputs

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 3PA: An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80...

See similar textbooks

Similar questions

Q1) Conduct an evaluation on the practical applications of the concepts of electromagnetism and submit a written report which includes the following. a) Design a circuit which utilizes the concept of electromagnetism and submit a simulation circuit for the same (use simulation tool of your choice) b) Write down the selected values of the components used for example the values of resistors, transistor used, capacitors etc c) Obtain the output for the ciruit using any sinks like CRO, loud speakers etc. d) Discuss about the principles of electromagnetism used in the simulation I WANT QUESTION (D)
You are tasked to design a dc power supply that operates from a single-phase ac supply (50Hz) with source inductanceof 1.5mH/phase. It is required to supply a dc load (resistive) with 55A at 322 Volt. Assume infinite inductive filtering andthe use of power diodes with a forward voltdrop of 0.7V. Consider the bridge converter topology and specify the followingdesign parameters,30) the loss in voltage due to commutation overlap;31) the r.m.s. ac supply voltage required;32) the overlap angle;33) the transformer utilisation factor;34) the rectification efficiency of the converter;35) the dc current rating of the rectifier diodes;36) the r.m.s. current rating of the rectifier diodes;37) the form factor of the diode current;38) the peak repetitive forward current rating of the rectifier diodes;39) the peak repetitive reverse voltage rating of the rectifier diodes.
10. An equivalent model is a combination of appropriately selected circuit elements that accurately simulates the real behavior of a semiconductor device in any operating condition. Select one: TrueFalse
(a) In your understanding explain how energy process occur when electron –hole pair are created and then when they recombine. Illustrate with diagrams. (b) Since the advent of integrated circuit (IC), the electronic industry continues to have various phases in its products. In your understanding kindly explain the four generations of integrated circuit. Show each generation applications.
draw a qpsk demodulation circuit using circuit components for instance resistors, capacitors, transistors etc
A conductor carries a current that may be regarded as equivalent to the sum of two components, one of them being a continuous direct current of 4.2 amp and the other a superimposed full-wave rectifier current. If the latter has a maximum value of 6.4 amp, calculate the average current in the wire if (a) both components have the same direction, (b) the two components are oppositely directed?
4.68 Using the exponential diode characteristic, show thatfor vS and vO both greater than zero, the circuit of Fig. 4.23(a)has the transfer characteristicvO= vS−vDat iD=1 mA−VT lnvO/Rwhere vS and vO are in volts and R is in kilohms. Note thatthis relationship can be used to obtain the voltage transfercharacteristic vO vs. vS by finding vS corresponding to variousvalues of vO.
An inter-connect bar is used in a device designed to operate between -20℃ and 60℃. It is 0.5mm long with a cross-sectional area of 0.025 mm2 and has to carry a current of 54 µA when a potential difference of 0.5 V is applied to it. B) The bar is made from silicon doped with acceptor atoms. Calculate the concentration of majority carriers and hence that of the acceptor atoms, assuming that the contribution of the minority carriers is negligible. Determine the minority carrier concentration please solve as soon as possible
Using battery modeled diodes, design the following limiters Transfer functions given in Fig. 3 while assuming Vi is a variable voltage source
An Engineer in electronic manufacture company is tasked to obtained an electric field across a PN junction? Apply your own understanding to explain the process he/she has to go through to obtain PN junction. Appropriate sketches should be used to support your answer
A conductor carries a current that maybe regarded as equivalent to the sum of two components, one of them being a continuous direct current of 4.2 amp and the other a superimposed half-wave rectifier current. If the latter has a maximum value of 8.3 amp, calculate the average current in the wire if (a) both components have the same direction, (b) the two components are oppositely directed?
Provide an overview of "Two Externally-powered transducers".Support your answer with pictures and examples