A copper [E = 106 GPa, a = 16.8x10-6/°C] rod (2) is placed within a steel [E = 212 GPa, a = 11.3x10-6/°C] tube (1) of the same length. The two components are connected at each end by pins that pass through both the tube and the rod. The outside diameter of the steel tube is D₁ = 102 mm, its inside diameter is d₁ = 79 mm, and its cross-sectional area is A₁ = 3270 mm². The diameter of the solid copper rod is d₂ = 55 mm, and its cross-sectional area is A2 = 2376 mm². Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by 52°C. Pin Answer: 02- i Steel Tube (1) Pin MPa Copper Rod (2)

A copper [E = 106 GPa, a = 16.8x10-6/°C] rod (2) is placed within a steel [E = 212 GPa, a = 11.3x10-6/°C] tube (1) of the same length. The two components are connected at each end by pins that pass through both the tube and the rod. The outside diameter of the steel tube is D₁ = 102 mm, its inside diameter is d₁ = 79 mm, and its cross-sectional area is A₁ = 3270 mm². The diameter of the solid copper rod is d₂ = 55 mm, and its cross-sectional area is A2 = 2376 mm². Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by 52°C. Pin Answer: 02- i Steel Tube (1) Pin MPa Copper Rod (2)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter1: Introduction

Section: Chapter Questions

Problem 13ETSQ

See similar textbooks

Similar questions

A rigid bar, AB, is pinned at point B. Two other bars, AC and AD, are connected to point A to provide support for AB. We are investigating the behavior of this system under a specific load. Key Details: Bar properties: Material: Steel with Young's modulus (Esteel) of 200 GPa and coefficient of thermal expansion (a) of 11.7 x 10^-6 /°C. Cross-sectional area: AC: 1960 mm² AD: 1250 mm² Length: AC: √2 meters (square root of 2 meters) AD: 1 meter Inclination angles: AC: θ₁ (theta 1) = 30° from horizontal AD: θ₂ (theta 2) = 20° from horizontal Load on bar AB: Idealized linearly increasing load with a maximum value of 30 kN/m at point B. Problem Objectives: Determine the internal forces (axial forces) acting within bars AC and AD due to the applied load on AB. Calculate the displacement of point A in both horizontal (dA,x) and vertical (dA,y) directions.If the bar is cooled by 10°C, what would be the: Determine the internal forces (axial forces) acting within bars AC and AD…
A uniform bar is connected to a tapered rod 2. Both are subjected to axial loads as shown . If P = 7kN Determine the axial deformation of uniform bar 1 (in mm) Indicate negative sign if compression. Complete solution no round off.
An elliptical gate covers the end of a pipe 4m in diameter. Of the gate is hinged at the top, what normal force F is required to open the gate when water is 8m deep above the top of pipe and the pipe is open to the atmosphere on the other side? Neglect the weight of the gate. Find: ħ in kPa Agate in m2 FR in kN ȳ in m I in m4 ycp in m F in kN
A 50 mm diameter cylindrical aluminum block is connected to 2 hollowed cylindrical steel blocks as shown in Figure. Both hollowed steel cylinders are of 60 mm and 40 mm outer and inner diameters respectively. The assembly is then connected to a rigid steel plate. Four bolts of diameter 10 mm are then used to rigidly fix the assembly to a wall. A force P is then applied to the assembly. The Modulus of elasticity(E) of steel is 200 GPa while aluminum has Modulus of elasticity(E) of 70 GPa. Both steel and aluminum have a yield strength (σy) of 250 MPa. The bolts have a yield stress (σy) of 800 MPa. All connections and joints are considered rigid.All lengths are in mm. a. Determine the allowable value of P that can be applied to the assembly taking into consideration theyielding of all parts of the assembly and bolts. Use a factor of safety of 1.5.b. Based on the value of P obtained part (a), determine the total elongation of the cylindrical steel block.c. Based on the value of P obtained…
Q5) A solid copper rod is of cross-sectional area 15 mm2 and length 2m. Calculate: a)its change in length when its temperature rises by 30oC b)the force needed to prevent it from expanding by the amount in (a). (given: for steel, the coefficient of linear expansion, α = 12 x 10-6 k-1 and young’s modulus is 2 x 1011 Pa) Assume that the proportional limit is not exceeded.
The steel and aluminum plate assembly is bolted together and fastened to the wall. Each plate has a constant width in the z direction of 200 mm and thickness of 20 mm. If the density of A and B is ρs = 7.85 Mg/m3, and for C,ρal = 2.71 Mg/m3, determine the location x̄ of the center of mass. Neglect the size of the bolts.
The rigid bar 2 m long is supported by a steel rod at the middle B and bronze rods equidistant from both ends at A and C as shown. The properties of the rods are given in the tabulation below. Steel Bronze Allowable stress 140 MPa 120 MPa Modulus of Elasticity, E 200 GPa 83 GPa Area, A 400 mm2 900 mm2 Length, L 1,000 mm What is the required length of the steel rod so the reactions on the three rods are the same? What is the required length of the steel rod so that both the steel and the bronze rods reach their allowable stresses at the same time? What is the maximum permissible load W that the rods can carry?
Both wires have a cross sectional area of 17 mm2 and are constructed of the same material with a modulus of elasticity of 200,000 MPa. 1. Determine the wires' tensile stress at C. 2. Determine the wires' tensile stress at D. 3. Calculate the maximum displacement possible.
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown . If P = 7kN Determine the axial deformation of rapered rod 2 (in mm) Indicate negative sign if compression. Complete solution no rounding off.
The rigid bar AOB is pinned at O and connected to aluminum and steel rods. Ifthe bar is horizontal at a given temperature, determine the ratio of the areas of the tworods so that the bar will be horizontal at any temperature. Neglect the mass of the bar.
Find a. Reaction at A in kN b. Deflection at B in mm c. Deflection at C in mm
A rigid bar AB is supported by three rods. A load P = 375 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10^6 kN/m^2 and modulus of elasticity of steel is 200 x 10^6 kN/m^2. a. Determine the deformation in the rods (in mm).