A copper rod and a steel rod are different in length by 5.00 cm at 0°C. The rods are warmed and cooled together. (a) Is it possible that the length difference remains constant at all temperatures? Explain. (b) If so, describe the lengths at 0°C as precisely as you can. Can you tell which rod is longer? Can you tell the lengths of the rods?

A copper rod and a steel rod are different in length by 5.00 cm at 0°C. The rods are warmed and cooled together. (a) Is it possible that the length difference remains constant at all temperatures? Explain. (b) If so, describe the lengths at 0°C as precisely as you can. Can you tell which rod is longer? Can you tell the lengths of the rods?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.3P

See similar textbooks

Similar questions

When determining the specific heat of a metal specimen, what would happen to your experimental results if too much cold water were placed in the inner calorimeter cup with the metal specimen? Why?
How much natural gas do you need to burn to heat twenty liters of water from 0 degrees C to 30 degrees C? and Calculate the amount of thermal energy required to raise the temperature of 80 liters of water from 20° C to 40° C. same formula?? and how do you do it?
Consider a 1 cm thick copper wall (k=375 W/m K) whose one surface is exposed to condensing water vapor (h=10000 W/m² K) at a temperature of 200°C . The other surface is in contact with ambient air (h= 5 W/m²K) at a temperature of 25°C. a) Calculate the heat per unit area across the plate. b) Determine the temperatures at both surfaces of the wall.
Why are the transient temperature charts prepared using nondimensionalized quantities such as the Biot and Fourier numbers instead of the actual variables such as thermal conductivity and time?
What is the effect of wind shear on thermals?
3.2 High-strength steel is required for use in building structures and equipment (e.g., cranes). It is produced by heat treating quench-hardened steel in a process called tempering that reduces brittleness and imparts toughness. In a production facility, alloy steel plates (k = 50 W/m K, c = 460 J/kg K, and ρ = 7865 kg/m3) of thickness 3.0 cm have to be tempered in a convective oven by heating them to 550°C. If the plates are initially at 40°C and the air inside the heat treating oven is at 700°C with a convective heat transfer coefficient of 45 W/m2 K, determine how long the plate has to remain in the oven.
Steel rods (1% carbon) that are 1.5 m long and 2 cm in diameter are heated in a furnace to850°C and then quenched in a water bath at 50°C for 40 s as part of a hardening process. Given the convective heattransfer coefficient is 750 W/m2K, find the average temperature of the rods when they are taken out of the bath.Show that lumping the rods is appropriate.
A 0.025-mm-diameter stainless steel wire having K =16 W/m • C is connected to two electrodes. The length of the wire is 80 cm and it is exposed to a convection environment at 20 •C with h = 500 W/m2 • •C. A voltage is impressed on the wire that produces temperatures at each electrode of 200 -C. Determine the total heat lost by the wire in cal/hr.
plz answer this ASAP,thx One surface of a copper plate that is 3 cm thick has a constant temperature of 400 ° C while the temperature of the other surface is kept constant at 100 ° C. Describe the temperature profile and how much heat is transferred across the plate ?, k copper = 380 watts/m.k with a cross -sectional area of 4 cm².
Determine the amount of heat that must be removed from 1 kg of water at 40°C to convert it to ice at -5°C.(Obtain any relevant data that you need from the internet. Cite the source of that data in your answer)
A 0.035-mm-diameter stainless steel wire having k = 16 W/m · ◦C is connected to two electrodes. The length of the wire is 85 cm and it is exposed to a convection environment at 20◦C with h =500 W/m2 · ◦C. A voltage is impressed on the wire that produces temperatures at each electrode of 200◦C. Determine the total heat lost by the wire.
Determine the ratio of thermal conductivity for N2 at sea level (T = 300 K, P = 1 atm) versusthe lower stratosphere (T = 230 K, P = 0.25 atm).