A copper-zine alloy has the properties shown in the table below. Grain Diameter (mm) Strength (MPa) 0.015 170 MPa 0.025 158 MPa 0.035 151 MPa 0.050 145 MPa Determine (a) the constants in the Hall-Petch equa- tion; and (b) the grain size required to obtain a strength of 200 MPa.

A copper-zine alloy has the properties shown in the table below. Grain Diameter (mm) Strength (MPa) 0.015 170 MPa 0.025 158 MPa 0.035 151 MPa 0.050 145 MPa Determine (a) the constants in the Hall-Petch equa- tion; and (b) the grain size required to obtain a strength of 200 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: You are given three metal test samples, with the same chemical composition and differing grain…

A: Given data grain dia of sample A = 5 micron = 0.005 mm grain dia of sample B = 10 micron = 0.01 mm…

Q: A machinist was tasked to insert an aluminum piston into a steel cylinder. The inside diameter of…

A: Given data Da=0.4998 mDs=0.5 m

Q: Consider the tensile stress-strain diagram in the figure below labeled 1 and 2. These diagrams are…

A: Strain-Hardening: Strain hardening (also known as work-hardening or cold-working) is the process of…

Q: Calculate the required weight of carbon necessary to obtain 12 ton of cast iron of the eutectic type…

A: rate of conversion=80%purity of carbon=65%eutectic type=4.3%weight=12 ton

Q: Calculate resolved shear stress on the (111) [01̅1] slip system of a unit cell in an FCC nickel…

A: The resolved shear stress is calculated from the following relation : τRSS=σapp(cosφcosλ)…

Q: 3) The strength of a titanium piece is found to be 65,000 psi when the grain size is 17 x106 m and…

A: (a) To find: The constant in Hall Petch equation. Given: When strength of material T piece is 65000…

Q: A copper-zinc alloy has the following properties: Grain Diameter (mm) Strength (MPa)…

Q: 1. Consider a single crystal of BCC iron oriented such that a tensile stress is applied along a…

A: Angle between 0 1 0 and 1 1 1 direction isλ=cos-1u1u2+v1v2+w1w2u12+v12+w12u22+v2+w22here for 0 1…

Q: Consider a single crystal of silver oriented such that a tensile stress is applied along a [001]…

A: Angle between tensile axis 001 direction and slip direction 101:…

Q: 1.0% of euctectoid carbon steel was slowly cooled from 900C to a temperature just below 723C 1.…

A: 1.0% of euctectoid carbon steel was slowly cooled from 900C to a temperature just below 723C 1.…

Q: You are given three metal test samples, with the same chemical composition and differing yield…

A: Given: Yield stress: A - 120 Mpa B - 140 Mpa C - 160 Mpa Grain size: A - 100 mm B - 25 mm To find:…

Q: In the Figure below, the tensile breaking strength, (sigma mark)tenstile-breaking = 140 Mpa…

A: Given: The tensile strength of the material = 140 Mpa The compressive strength of the material = 460…

Q: A hypo-eutectoid steel sample has a mass of 538kg and a nominal carbon content of 0.57%. Sketch the…

A: From the given data,

Q: From the grain distribution curve, D60 = 1.45 mm, D30 = 0.75 mm and D10 = 0.45 mm. Determine the…

A: Write the formula for uniformity coefficient. Cu=D60D10 Here, Cu is the uniformity coefficient, D60…

Q: A sold-worked brass specimen of ayerage grain size 0.02 mm has a xield strength of 160 MPa. Estimate…

Q: 11.) For these metal specimens, which of the following statements is wrong a) The strength and…

A: Answer: Statement b is false

Q: You have the choice to either purchase a copper alloy that has an ASTM grain size of 5 or ASTM grain…

A: The relation between ASTM grain size and number of grain per square inch is given as – Now it has…

Q: An HCP alloy, known as Hertzalloy 200, has a c/a ratio of 1.600. a. Identify the most probable slip…

A: Given, The alloy is hexagonal-close-packed (HCP). c/a = 1.600

Q: Consider an aluminum polycrystal with a grain size of 10 μm. If a dislocation source at the center…

A: Data given - grain size = 10 μm applied shear stress = 50 MPa G = 26 GPa b = 0.3 nm.

Q: 7. The tensile strength of polycrystalline spinel can be approximated using the Hall- Petch…

A: Given Data⇒ Hall Petch relation Spinel has a grain size d1=μm d1=5×10-3 mm Tensile strength σy1=200…

Q: Calculate resolved shear stress on the (111) [011] slip system of a unit cell in an FCC nickel…

A: given; ⇒slip (111) ,011 and 001⇒diagram for mentioned slip

Q: Problem2: Figure 10 is a micrograph of an alloy at a magnification of 200x. Find the ASTM grain…

A: Given-Data:- Magnification =200x To-Find:- ASTM Grain size

Q: Schematic room temperature microstructuresfor four iron-carbon alloys are shown below. 1- Explain…

Q: With regard to the process of slip, a Burgers vector's direction correspc dislocation's slip…

A: Aluminium Atomic Radius = 0.1431nmChromium Atomic Radius =0.1249nm To-Find:- Values of magnitudes of…

Q: Calculate the resolved shear stress on the (111)[0-11] slip system of a unit cell in an FCC nickel…

A: To determine the shear stress

Q: а) Briefly describe the mechanical properties of those microstructure and suggest how to obtain the…

Q: (b) Figure 1 shows, the tensile engineering stress-strain curve for an aluminum alloy. Based on…

A: According to the details provided in the question, we need to calculate 1. yield strength 2.…

Q: 4. A 40-mm-diameter bar made of 4140 steel is quenched in an agitated oil bath. The expected Ro…

A: We have to determine A 40-mm-diameter bar made of 4140 steel is quenched in an agitated oil bath.…

Q: Q.: A stress of 75 MPa is applied in the [001] direction on an fcc single crystal Calculate: M (a)…

A: Given: The stress along a plane = 75 Mpa

Q: You are given three metal test samples, with the same chemical composition and differing grain…

Q: When a uniaxial tensile stress (of symmetry o/mmm) is applied to cubic crystal of symmetry m3m, what…

A: (a)

Q: What is the difference between coarse and fine pearlite in terms of (1) microstructure and (2)…

A: Pearlite is a composite microstructure. The combined arrangement of lamellae or thin layers of…

Q: From the grain distribution curve, D60 = 1.45 mm, D30 = 0.75 mm and D10 = 0.45 mm. Determine the…

A: Given- D60 = 1.45 mm D30 = 0.75 mm and D10 = 0.45 mm

Q: You are given three metal test samples, with the same chemical composition and differing grain…

Q: 7. The tensile strength of polycrystalline spinel can be appi Petch relation. If the spinel has a…

A: Write the expression for hall patch relation.

Q: The properties of a titanium allow used in commercial airplanes are shown in the table: Grain Size…

A: (a) The general equation of the Hall-Petch equation is, σy=σi+K·d-12 where σi and K are the…

Q: Using the values found in the previous two questions, use the Hall-Petch equation and the graph…

Q: Compute the dislocation density in tungsten if the flow stress is controlled by the stress necessary…

A: Given: τ=50 MPaG=166 GPa

Q: The yield strength for an alloy that has an average grain diameter of 4.0 x 102 mm is 107 MPa. At a…

Q: The yield strength for an alloy that has an average grain diameter of 4.7 x 10² mm is 134 MPa. At a…

Q: an alloy with an avg grain diameter of 0.053mm is l16MPa. When the grain diameter is 0.0087mm, the…

Q: The yield strength for an alloy that has an average grain diameter of 5.2 × 10-2 mm is 110 MPa. At a…

Q: Explain the differences in grain structure for a metal that has been cold worked and one that has…

A: INTRODUCTION Cold working : Cold working is the most common way of reinforcing metals through…

Q: A machinist was tasked to insert an aluminum piston into a steel cylinder. The inside diameters of…

A: Write the given values with the suitable variables. dc=0.500 mdp=0.4998 mT1=25 °C Here, dc, dp, and…

Q: 3/ Determine the change percentage in volume and APF that occurs in Titanium as a result of heating…

A: Given Dataa=0.292nmC=0.463nm

Q: Calculate the dislocation spacing of a low-angle tilt boundary in aluminum for θ = 0.5◦. Take G =…

Q: Bainite phase and pearlite phase have different mechanical properties due to its structure…

A: Bainite: It is a plate like structure which forms in steels at 125-550 C Pearlite: It is a mixture…

Q: 1600 Question 4. An austenitized 4340 standard steel bar is cooled at different rates (see Figure…

Question

A copper-zine alloy has the properties
shown in the table below.
Grain Diameter (mm) Strength (MPa)
0.015
170 MPa
0.025
158 MPa
0.035
151 MPa
0.050
145 MPa
Determine
(a) the constants in the Hall-Petch equa-
tion; and
(b) the grain size required to obtain a
strength of 200 MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cold worked brass specimen of average grain size 0.02 mm has a yield strengh of 160 MPa. Estimate the sield strenath of this alloy affer it hasbeen heat teated and the value of ky is 12.0 MPa-mm* 2
An uncold-worked brass specimen of average grain size 0.006 mm has a yield strength of 178 MPa. Estimate the yield strength of this alloy (in MPa) after it has been heated to 600°C for 1000 s, if it is known that the value of ky is 11 MPa-mm1/2. The Animated Figure 7.25 may be helpful. Attached is the question and the figure referenced.
A 609 g eutectoid steel ( about 0.8%C) is heated to 1,002 C and cooled slowly through the eutectorid temperature. This results in the formation of cementite Fe3C (6.67%C) and ferrite (0.025%C). Calculate the number of grams of cementite that form in the steel.
Compute for the composition, in atom percent, of an alloy that consists of 92.5 wt% Ag and 7.5 wt% CuWrite Legibly
A copper-zinc alloy has the following properties: Grain Diameter (mm) Strength (MPa) 0.015 170 MPa 0.025 158 MPa 0.035 151 MPa 0.050 145 MPa Determine (a) the constants in the Hall-Petch equation; and (b) the grain size required to obtain a strength of 200 MPa.
Please do it as early as possible. Name the microstructural products of a eutectoid iron-carbon alloy (0.76 wt% C ) that is first completely transformed to austenite and then cooled to room temperature at a rate of 1000 °C/s
An alloy of 30 wt % Pb and 70 wt % Sn is slowly cooled from 250°C to 27°C: d) What is the amount and composition of each phase that is present at 183°C - ∆T ? e) What are the amounts of each phase present at room temperature? f) Draw the microstructure 183°C + ∆T and 183°C - ∆T in 2 cm diameter circle.
Bainite phase and pearlite phase have different mechanical properties due to its structure differences. Discuss the hardness and tensile strength of these 2 phases using isothermal transformation temperature diagram.
In an Al casting ingot containing 2wt.% Cu, the content of Cu at grain boundaries has reached 12wt.%. How long this ingot should be held at 530 K to attain a difference of 10% in Cu concentration between center and boundary of the grains. The mean distance from the center of grains to the boundary is 100μm. Du= 3.9x10⁹ cm²/sec
The magnesium-lead alloy was cooled from 600°C to 450°C. Microstructures are composed of initial Mg2Pb and process microstructures factors. Find the composition of this alloy if the weight fraction of the microorganism factor is 0.28.
For a 70-30 Zn-Cu alloy, what would the percent of each phase be at 800°C and 500°C?
The composition of the α in an 42 wt% griffinium alloy at 662 degrees centigrade is (enter the wt% griffinium)