A curved gate in the shape of the circular arc was used to hold oil and water in the container shown. If it is hinged at point O and the gate is 4 m wide into the paper oil (0-86) Hh₂0 B Determine the Reaction at Hinge O. 2m 2m R=6m 30⁰ O

A curved gate in the shape of the circular arc was used to hold oil and water in the container shown. If it is hinged at point O and the gate is 4 m wide into the paper oil (0-86) Hh₂0 B Determine the Reaction at Hinge O. 2m 2m R=6m 30⁰ O

Name: A curved gate in the shape of the circular arc was used to hold oil a
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A curved gate in the shape of the circular arc was used to hold oil and water in thecontainer shown. If it is hinged at point O and the gate is 4 m wide into the paperoil (0.86)H₂0BDetermine the Reaction at Hinge O.2m2mR=6M30°O

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
The 1.20 m diameter cylinder 2.00 m long is acted upon by water on the left and oil having s = 0.80on the right. Determine the height of water for the horizontal component of the reaction at B to bezero, if the height of oil is 1.20 meters.
Plate AB has a width of 1.5 m and a radius of 3 m. Determine the horizontal and vertical components of reaction at the pin A and the vertical reaction at the smooth stop B due to the water pressure. Strictly using General Solution, and please show pressure diagram.
A quater-circular plate is pinned at A and tied to the tanks wall using cable BC. The tank and plate are 7ft wide. gamma w= 62.4 lb/ft^3. Determine the x and y component of reaction at A and determine the magnitude of the tension in the cable due to the water pressure.
The initial pressures at A and B are the same at 103 kPa. If the pressure at the liquid at A (SG1 = 1.25) is increased to 148 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.51 cm, and the inclination of the tube is 18 degrees with respect to the horizontal. Assume unit weight of air to be negligible.
Determine the volume of the body (s=3.0) that is required to keep the gate in the position indicated in the figure. The gate is 2.40m wide and 4.2m long.
The uniform control gate AB shown is pinned at A and rests on the smooth surface at B. The gate has a width of 1m. If the gate has a mass of 3.9 Mg, determne the maximum depth of water h in the reservoir that will cause the gate to be on the verge of opening.
Using the figure Determine the reaction force on the smooth support at B due to the fluid pressure on the gate. The width of the gate into the page is 1.5 m and the density of the water is 1000 kg / (m3) .
The 280-kg, 6-m-wide rectangular gate is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force at its center. Determine the minimum force F required to open the water gate.
The 2 m diameter and 3.6 m high cistern tank contains kerosen (s.g. =0.8), glycerin (s.g.=1.6) and water each with 1.2 m depth. The hoops are used to reinforce the tank that is each placed at 0.5 m from the edge. a. Determine the hydrostatic force in the tank. b. Determine the hoop tension at the top. c. Determine the hoop tension at the bottom.
A 4-m-high, 5-m-wide rectangular plate blocks the end of a 4-m-deep freshwater channel, as shown inthe Figure 2 below. The plate is hinged about a horizontal axis along its upper edge through a point Aand is restrained from opening by a fixed ridge at point B. Determine the force exerted on the plate bythe ridge. Clearly state all asuumptions and illustrations.
A fish tank that contains 60 cm high water is moved in the cabin of elevator. Determine the pressure in kPa at the bottom of the tank when the elevator is stationary. Include the free body diagram in your solution. a.7.69 b.5.89 c.6.46 d.4.09