A cylinder is made of steel plate is intended to be used as a container for compressed air. The dimensions of the cylinder are L-2m, D=60cm, and t = 0.005m. If the ultimate tensile stress of the steel is 400 N/mm², Young's modulus is 200000 MPa and Poisson's ratio is 0.25. 1- Determine the maximum air pressure that can be stored in the cylinder (use factor of safety = 2) 2- Determine the change in the volume of the cylinder due to storing maximum pressure.

A cylinder is made of steel plate is intended to be used as a container for compressed air. The dimensions of the cylinder are L-2m, D=60cm, and t = 0.005m. If the ultimate tensile stress of the steel is 400 N/mm², Young's modulus is 200000 MPa and Poisson's ratio is 0.25. 1- Determine the maximum air pressure that can be stored in the cylinder (use factor of safety = 2) 2- Determine the change in the volume of the cylinder due to storing maximum pressure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The strength per meter of the longitudinal joint in the figure is 480 kN, whereas or the girth joint is 200 kN. Determine the maximum diameter of the cylindrical tank if the internal pressure is 1.5 MPa.
The test tube opens at 293 K with 13 cm Hg at the bottom, and 5.6 cm water above Hg. Calculate the pressure at the bottom of the tube if the atmospheric pressure is 760 mm Hg. Use a density of 13.55 g / cm3 for Hg and 0.998 g / cm3 for water. Give answers in terms of dyne / cm2, psia, and kN / m2 • (See conversion table). = kPa. = ..... dyne / cm2. = .... psia = ....
A cylindrical steel tank having an internal diameter of 50 in. is submerged in seawater (weight density =64⁢ lb/ft3) to a depth of 9750 ft. The internal gage pressure in the tank is 1600 psi. (a) If the allowable stress of the steel is 32 ksi, what is the minimum allowable outside diameter of the tank? (b) What is the maximum tensile stress before the tank is immersed? Determine the external pressure of the seawater at a depth of 9750 ft. po= psi Determine the maximum magnitude of σr produced in the tank. σr = psi Based on the maximum magnitude of σr produced in the tank from Part 2, is there an outside diameter for which the radial stress magnitude will exceed the allowable stress of the steel in this case? More calculations are needed. No Yes For this case, choose the correct statement regarding the maximum magnitude circumferential normal stress. It occurs at the outer surface of the tank, and it is tensile. It occurs at the outer surface of the tank, and it…
A thin-walled hollow sphere 3.8 m in diameter holds helium gas at 1767 kPa. Determine the minimum wall thickness of the sphere in mm if its allowable stress is 84.8 MPa.
5.) A lO-kN car and 5-kN hoist are supported 1.8 m above the floor by a cylinder with a 300-mm bore . What pressure will this develop in the system?
A hydrogen-filled balloon is to expand to a sphere 20 m diameter at a height of 30 km where the absolute pressure is 1100 Pa and the temperature is – 40 degree C. If there is to be no stress in the fabric of the balloon, what volume of hydrogen must be added at ground level where the absolute pressure is 101.3 kPa and the temperature is 15 degree C?
Q 244 What are the reaction forces on the latch an djoint in the gate below? And in case thefloodgate is reversed (concave)? *The gate is a cylinder room with length L = 5 m
The test tube opens at 293 K with 15 cm Hg at the bottom, and 7.5 cm of water above the Hg. Calculate the pressure at the bottom of the tube if the atmospheric pressure is 760 mm Hg. Use the density of 13:55 g / cm3 for Hg and 0998 g / cm3 to air.Berikan answers in terms of dyne / cm2,psia, and kN / m2 • (see conversion table). a. … KPa. b. … Dyne / cm2. c. … Psia.
The piston shown in figure is held in equilibrium by thepressure of the gas flowing through the pipe. The pressurespI = 350 kPa, pII = 130 kPa, and pressure of the gas pIII =210 kPa. Find the mass of the piston. Ans: 80.1 kg Hints: Consider a free body diagram of the piston andidentify the different forces the piston is subjected to get theweight of the piston. The weight of the piston isnumerically equal to its mass since g is not given meaningat standard gravity
Find a) the total force on gate AB in KN and b) the position of the center of pressure in m with respect to the bottom of the pond. Assume that the gate is 8 feet wide, that 1ft = 0.3048m, and that 1PSI = 6897.1 Pa
A water tank 3m in diameter and 6m high is made from 12mm thickness of steel. When the tank is filled with water: - Determine the circumferential stress - And the tension force in the vessel
Find a) the total force on gate AB in KN and b) the position of the center of pressure in m with respect to the bottom of the pond. Assume that the gate is 8 feet wide, that 1ft = 0.3048m, and that 1 psi = 6897.1 Pa. Relative density salt water 1.025.