A cylinder-piston assembly contains 1 kg of a substance at 100 kPa. The initial volume is 0.5 m3. Heat is transferred to the substance in an amount necessary to cause slow expansion at constant temperature. This process ends when the final volume is twice the initial volume. Determine the magnitude of the heat transferred if the substance is: a) Nitrogen (ideal gas. Assume constant specific heat) b) Water

A cylinder-piston assembly contains 1 kg of a substance at 100 kPa. The initial volume is 0.5 m3. Heat is transferred to the substance in an amount necessary to cause slow expansion at constant temperature. This process ends when the final volume is twice the initial volume. Determine the magnitude of the heat transferred if the substance is: a) Nitrogen (ideal gas. Assume constant specific heat) b) Water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2°C 500 //(Kg.°C), is The quantity of heat required to raise the temperature of 500 g of iron by given that the specific heat capacity is 500 kJ 05 kJ 2 KJ O250 KJ
6. If 8 lbs of a substance receives 240 Btu of heat at constant volume and undergo a temperature change of 150oF. What is the average specific heat of the substance during the process? (3 DECIMALS IN FINAL ANSWER PLS)
2°C The quantity of heat required to raise the temperature of 500 g of iron by 500 J/(Kg. C), is given that the specific heat capacity is 500 kJ 0.5 kJ 2 KJ 250 KJ
2. Four kilogram of certain gas is contained within the piston- cylinder assembly. The gas undergoes a process for which the pressure -volume relationship is PV1.5 = C. The initial pressure is 3 bars, the initial volume is 0.1 m3 and the final volume is 0.2 m?. The change in internal energy is – 4.6 KJ Determine the heat kg' transfer for the process in KJ.
2.0 lb of water inside a piston-cy inder assembly undergoes the following two processes in series Process 1-2: Contant pressure cooling from a saturated vapor at p1 = 170 psi until x2 = 80%. Process 2-3: Constant volume heating to a saturated vapor. There are no changes in kinetic or potential energy. Find the work for process 1-2 in Btu. Find the heat transfer for process 1-2 in Btu. Find the work for process 2-3 in Btu. f) Find the heat transfer for process 2-3 in Btu.
Saturated water vapor initially at a pressure of 225 kPa and volume 0.01 is contained in a piston cylinder assembly. The water undergoes two processes in series:Process 1-2: Constant volume process till the pressure is 2 bars.Process 2-3 : Constant pressure process till the volume is doubled.Determine:a) the temperature at state 3b) the total amount of work for process 1-3c) the total amount of heat transfer for process 1-3. v1 (m3/kg) Format : 0.72765 m (kg) Format : 0.0622 v3 (m3/kg) Format : 7.8553 W2-3 (kJ) Format : 5.7285 u1 (kJ/kg) Format : 2832.5 u2 (kJ/kg) Format : 7592.79 Q1-2 (kJ) Format : -4.87 u3 (kJ/kg) Format : 8499.67 Q2-3 (kJ) Format : 60.34 Q1-3 (kJ) Format : 5.9 T3 (oC) Format : 822.09
Question: A piston cylinder device initially contains superheated steam as shown in the following figure. Then it starts losing heat and as result piston moves down to the set of stops where it contains saturated liquid water. The heat loss process continues until the system contains water at 473K. Determine, a) The final pressure and quality (if any) b) The boundary work c) Amount of heat total transfer Steam 0.35 kg 3.5 MPa Superheated by 7.4°C
In a vertical piston cylinder arrangement, there is 300 kPa pressure and 2 kg of saturated liquid and saturated steam mixture water at 70% dryness in the cylinder. As a result of the heat transfer to the cylinder, the piston moves by increasing slowly at constant pressure and the heat transfer ends when the volume increases 2.5 times. a)Find the temperatures, specific volumes and specific internal energies in the initial and final states. b)Draw the P-v diagram of the process schematically, show the initial and final states on the diagram. c)Find the work done to the environment by the system during the process, kj d)Find the heat transfer, kj, to the system during the process.
2.0 lb of water inside a piston-cy inder assembly undergoes the following two processes in series Process 1-2: Contant pressure cooling from a saturated vapor at p1 = 170 psi until x2 = 80%. Process 2-3: Constant volume heating to a saturated vapor. There are no changes in kinetic or potential energy. a) Find the specific volume for state 1 in ft3/lb. b) Find the specific volume at state 2 in Ft3/lb
1. A certain ideal gas Y has molecular weight of 25 g/mol and specific heat ratio of 3. Initially, Y has pressure of 200kPa and volume of 2m3. The volume was doubled during heat transfer. Find the heat transfer if it underwent a process described by ( a. n=1 b. n=Cp/Cv C. n=2
In a piston-cylinder assembly, there is initially 2 kg of water at a temperature of 25 °C and a pressure of 100 kPa. Then heat is given to the water until its volume is 0.4 m3. At this point, the piston in the cylinder is fixed with a stopper, but the water in the cylinder continues to heat until its temperature reaches 300 oC. According to this, calculate a) the final pressure of the water, b) the amount of heat given to the water, c) the work done by the piston. d) Show these processes in the T-v (Temperature-Specific Volume) diagram
3.0 kg of steam at a pressure of 100 kPa are contained in a rigid sealed tank of volume 5.95 m3. The steam begins to cool as heat is transferred to the atmosphere. When the internal pressure reaches 10 kPa, the tank walls will collapse.a) What is the initial temperature of the steam in the tank (in oC)?b) What will the temperature be in the tank when the walls collapse (in oC)?c) Attheinstantofcollapse,whatisthemassofwaterinthevapourandliquidstate (in kg)?d) Deduce the work done for this process