A cylinder weighing 20 pounds slides in a free pipe as shown in the figure. The clearance between the cylinder and the pipe is 0.001 in and it is filled with oil of relative gravity 0.80. If the cylinder is observed to decelerate at the rate of 2 ft/s^2 when the speed is 20 ft/s. Calculate dynamic and kinematic viscosity W= 20lbμ=? %3D S oil = 0.80 p = ? %3D V = 20ft/s e.cciinche, Bipelyne efinder 5 inches

A cylinder weighing 20 pounds slides in a free pipe as shown in the figure. The clearance between the cylinder and the pipe is 0.001 in and it is filled with oil of relative gravity 0.80. If the cylinder is observed to decelerate at the rate of 2 ft/s^2 when the speed is 20 ft/s. Calculate dynamic and kinematic viscosity W= 20lbμ=? %3D S oil = 0.80 p = ? %3D V = 20ft/s e.cciinche, Bipelyne efinder 5 inches

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Similar questions

Q5. A brass cube “R” inch on a side weighs (Rx10)lb.Hold this cube in equilibrium underwater by attaching light foam buoy to it. If the unit weight of foam is 4.5 lb/ft3, calculate the minimum required volume of the buoy? (where R is ) 32)?
A cylindrical piston of weight 5N slides in a lubricated pipe as shown in figure.The clearance between the piston and the pipe is 0.025 mm. If the piston decelerates at0.5 m/s2 when the speed is 5 m/s, what is the viscosity of the oil ?
Q.1 Calculate Reynold’s Number if kinematic viscosity of a liquid is 0.001 m2/s , density is 500 kg/m3 flowing through dia of 10 mm with velocity of 30m/s?
A container holds two layers of different liquids, one fluid having a specific gravity of 1.1 is 30cm deep and the other fluid having a specific gravity of 1.6 is 40cm deep. A solid cubical metal having an edge dimension of 18cm and specific gravity of 6.5 is submerged such a manner that half of the cube is on the top layer and the other half in the bottom layer of fluids with the square base of the cube horizontal. Help me compute the weight WCUBE of the cubical metal in newtons, compute the buoyant force BFCUBE in newtons acting on the metal object, and compute the tension T in newtons in the wire holding the cube to maintain its position. please draw a figure
An engineer sees a water flow through a 0.4 km long and 200 mm diameter pipe having a roughness of 0.0015 mm at 0.075 cubic meter per second. Assuming that the property of H2O is u = 0.001 Nm/sec and p = 1 g/cu.m. He is bored, so he wanted to calculate the following, help him. a. the pressure drop cause of friction b. velocity of H2O in the pipe c. find the Re?
A 40 mm plastic sphere (?? = 1.3) is dropped in a certain oil (?? = 0.85, μ =3.6 × 10−2 Pa∙s).(a) Determine its terminal velocity(b) If this sphere starts to rotate at 25 revolutions per second in the clockwise direction. Determine the magnitude and direction of the Magnus force
A closed pressurized tank shown below is filled with oil and mercury. Mercury is confined in an internal reservoir inside the closed tank, the height of mercury is 450mm. An open manometer is placed on the bottom left part of the tank with liquid “X” as its gage liquid , the deflection from the gage liquid shows 800mm. Determine the following:a) Height of the oil from point A up to point c if height A to C is 5 times the height of y. b) Pressure @ point B in kPa. c) Pressure @ point C in psi.
A plunger (54 mm Ø and 0.5 m long) is moving through a horizontal cylinder (60 mm Ø) containing oil at a speed of 8 m/sec that has a viscosity of 7.1x10-6 m2/sec and specific gravity of 0.84. Calculate the force needed to maintain its velocity. Use 2 decimal places.
A right circular cone is 50mm in radius and 170mm high and weighs 2.1 N in air. It is placed to float in ethanol (sg = 0.79) with its vertex down ward Calculate the depth of submergence of the cone in mm and How much force is required to push this cone vertex downward into the ethanol so that its base is exactly flushed at the surface in N?
A closed pressurized tank shown below is filled with oil and mercury. Mercury is confined inan internal reservoir inside the closed tank, the height of mercury is 450mm. An openmanometer is placed on the bottom left part of the tank with liquid “X” as its gage liquid , thedeflection from the gage liquid shows 800mm. Determine the following:a) Height of the oil from point A up to point c if height A to C is 5 times the height of y.b) Pressure at point B in kPa. c) Pressure at point C in psi.
A steady push on the piston in a syringe is shown in the figure causes a flow rate of 0.4 ml/sec. The fluid has a mass density of 900 kg/cum and an absolute viscosity of 0.002 Pa-sec. Assume that there is no headloss in the larger cylinder. Determine the reynolds number for the given flow of 0.4 ml/sec in he needle. 645 917 897 795 Determine the headloss in the needle 18.90 m 15.21 m 14.43 m 16.23 m Determine the force required to maintain the flow 64.23 kn 45.25 kn 34.77 kn 25.36 kn
A block weighing 1 kN and having dimensions 200 mm on an edge is allowable to slide down an incline on a film of oil having a thickness of 0.005 mm. If we use a linear velocity profile in the oil. What is the terminal speed of the block. The viscosity of the oil is 7x10-3 N.s/m?