right circular cone is 50mm in radius and 170mm high and weighs 2.1 N in air. It is placed to float in ethanol (sg = 0.79) with its vertex down ward Calculate the depth of submergence of the cone in mm and How much force is required to push this cone vertex downward into the ethanol so that its base is exactly flushed at the surface in N?

right circular cone is 50mm in radius and 170mm high and weighs 2.1 N in air. It is placed to float in ethanol (sg = 0.79) with its vertex down ward Calculate the depth of submergence of the cone in mm and How much force is required to push this cone vertex downward into the ethanol so that its base is exactly flushed at the surface in N?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 45P

See similar textbooks

Similar questions

SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the pressure required to decrease the volume of the oil by 2%?
A hollow cylinder 2.46-m in diameter and 7-m long weighs 3,159 N. How many cubic meters (m3) of metal weighing 112 kN/m3 must be placed inside the cylinder such that 2.9 m. of the cylinder is protruding above the liquid surface? The hollow cylinder is submerged in a liquid that has a specific gravity of 2.3. Round off to four decimal places.
3. A brass sphere (sp.gr. 8.60) is placed in a body of mercury. If the diameter of the sphere is 30cm. a. What minimum force would be required to hold it submerged in mercury? b. What is the depth of floatation of the sphere when it is floating freely?
A cylinder vessel filled with water with a 2m diameter and 5m high. It was rotated with uniform angular velocity and spilled half of its volume. A)Estimate the pressure at the center of paraboloid in Pascals when it is rotating. B) Estimate the depth of paraboloid in meters when it is rotating. C)estimate the velocity in rev/s when its rotating
Oil is filled within a tall cylindrical tank. A flat disk with a height of 1 cm and with a diameter of 5 cm is placed into the oil. There occurs a narrow spacing of 0.1 mm between the disk and the tank wall. Due to the forces acting on the disk, it moves downward, and after some time, the speed of the disk reaches a terminal velocity. Beyond this moment, measurements reveal that the disk moves 30 cm in 4 seconds. If the oil density is 600 kg/m3and the specific gravity of the disk is 1.5, determine the oil’s viscosity.
a circular cone s(0.99) floats vertically as shown in the figure, determine if it is stable or unstable, for that position R=0.75m and h=1.50m
A 40 mm plastic sphere (?? = 1.3) is dropped in a certain oil (?? = 0.85, μ =3.6 × 10−2 Pa∙s).(a) Determine its terminal velocity(b) If this sphere starts to rotate at 25 revolutions per second in the clockwise direction. Determine the magnitude and direction of the Magnus force
The space between two flat plates of 1 cm in length has been filled with a liquid whose relative density is 0.8. Determine the kinematic viscosity if the force required to displace the 4000 cm ^ 2 top plate at a speed of 20 cm / s is 0.07N.
A solid object having a specific gravity of 3.5 is floating on a liquid having a specific gravity of 13.6. The volume of the object is 0.02 cubic meters. What additional vertical force is required to completely submerge the liquid?
An open vessel 4.0m wide, 5.0m long and 3.5m deep contains 3m of water. It is then accelerated to the right along its width. a. Calculate the acceleration just about water to spill. b. At this rate, what is the force (in N) causing the acceleration if the mass of the vessel if the mass of the vessel is 600kg? c. Consider the same vessel accelerated at 7.00 m/s2. Determine the volume (in m3) of water spilled at that acceleration.
Fluid Mechanics A drop of water at 20oC is forming under a solid surface. The configuration just before separating and falling as a drop is shown in the picture. Assume the forming drop has a volume of a hemisphere and the force holding the drop to the surface is the surface tension. What is the diameter of the hemisphere just before separating?
A mass of 2 kg is projected with a speed of 3m/s up a plane inclined 20° with the horizontal. After traveling 0.8m, the mass comes to rest. Determine the coefficient of friction.