A cylindrical object 77mm diameter, 162mm height and a mass of 613g, is placed in the tank, which contains oil (51mm thick) and water. Calculate the height(in mm) above the surface of the oil at which it will float if maintained in the vertical position. Take density of oil equals 975 kg/m³.

A cylindrical object 77mm diameter, 162mm height and a mass of 613g, is placed in the tank, which contains oil (51mm thick) and water. Calculate the height(in mm) above the surface of the oil at which it will float if maintained in the vertical position. Take density of oil equals 975 kg/m³.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Related questions

Q: Problem 3. A vapor power plant produces 25 kg/s steam at 6 MPa, 500°C, in the boiler. It cools the…

Q: Which one of the following is a wrong statement. Paint is a non-Newtonian fluid Water and air are…

A: Sol^n :- The real fluid viscosity is never zero.yes, the viscosity does not show in a static fluid…

Q: What is not a type of resultant internal load in a member? O Normal Forces O Bending Forces Applied…

Q: What is the purpose of reheating steam in the reheat cycle?

A: Reheating is a process in which expansion of steam takes place in multiple stages or multiple…

Q: 5. A trough full of water is 20ft. long and its cross section is in the shape of an isosceles…

Q: Aircraft B Gross weight 1,600 lb Wing Area 250 ft Maximum thrust Co 0.011 K 0.022 1.45 max Mdr I NB…

A: Given Data : Gross weight =1600 lb CD0=0.011K=0.022CLMax=1.45NB=1.466 ft/secWe have to find out…

Q: A water tube boiler is made of DN 500 schedule XS pipe (NPS20) conforming to SA 285B. A DN 200…

A: Answer: There are three F-values in the study, one for each of the three factors being explored. It…

Q: A reheat-regenerative rankine cycle operates on a turbine efficiency of 95% and pump efficiency of…

A: Given we have P7=15Mpa h7=3581.5 KJ/kgT7=600° C S7=6.677 KJ/kgkp8=10Mpa h8=3436.8…

Q: Steam, initially at 5 MPa, 280°C undergoes a polytropic process in a piston-cylinder assembly to a…

Q: The cross-sectional dimensions of a beam are shown. Assume b=3.25 in., t=tw=0.1875 in. and d=2.5 in.…

A: Answer: (a) Internal bending moment is 41.7583 lb•ft. (b) Bending stress at point H is -520.2308 psi…

Q: find the relative amounts (in terms of mass fractions) of the phases for the following alloys and…

A: For the given composition we will need to refer to the Cu - Zn phase diagram. At 400 C and 90 wt%…

Q: Avapor-compression heat pump has a heating capacity of 500 kl/min and uses Refrigerant 134a asthe…

A: Given data Heating capacity of heat pump= 500 kJ/min = 8.33333 kJ/sThe following are the various…

Q: An idealised Rankine cycle with superheat is shown below. 2 a. Show on the diagram (or describe as…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

Q: STELIA Aerospace are planning to design a spherical cryogenic tank to be stored with liquid…

A: (a) Calculate the mass flow rate that is actually used to fill the tank.…

Q: 76. All surfaces of an infinitely lang heating element, having a cross section in the shape of a…

A: Given Thermal conductivity, k = 35 W/m.K Temperature, T1 = 400C…

Q: If the power generated by a wind system at a height of 50 m is equal to 30 kw at a wind speed of m/s…

Q: » call Phonldigbal bakberies camera

A: A battery is a device that stores and transforms chemical energy into electrical energy.…

Q: neating maintained at 300 C. Due to symmetry, only a quarter of the cross section is shown in the…

A: Given Thermal conductivity, k = 35 W/m.K Temperature, T1 = 400C…

Q: 5 planks (4@ 40 x 40 mm and 1@40 x 380 mm), joined together forming |-section (shown in figure).…

Q: The force system shown is composed of three forces: A = 35.75 kN, B = 41.83 kN. If β = 56.36°, what…

Q: 6. A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The allowable shear stress for the…

A: Answer: The diameter of the shaft is 50 mm.

Q: For the connection shown, the average shear stress in the 14-mm-diameter bolts must be limited to…

A: Given is a double shear connection.

Q: "The capacity of a certain pump is 9780 gallons per hour with a capacity of 73.47%. A city uses this…

Q: 5.32 PQ< What is a control surface and a control volume? Can mass pass through a control surface?

A: There are three types of the systems1. control volume open system2. control mass closed…

Q: The force system shown is composed of three forces: A = 39.60 kN, B = 43.86 kN. If β = 50.46°, what…

A: Draw a diagram resolving the given forces in the horizontal and vertical directions. For…

Q: e general solution for flux inside the sphere is given by: Ø(r) = ierIL + C2 erle r here C¡ and C2…

A: given data the general solution for a pointry socuce with in a medium flux is…

Q: The gage pressure in a liquid at a depth of 3 m is read to be 49 kPa. Determine the gage pressure in…

Q: 26 PA PB Water Water Oil Manometric fluid Manometric fluid Find the pressure difference at two…

Q: 76. All surfaces of an infinitely lang heating element, having a cross section in the shape of a…

A: Given Thermal conductivity, k = 35 W/m.K Temperature, T1 = 400C…

Q: HW-1- Find the Destination Numbers of following Refrigerant chemical formulas No. Refrigerant…

A: Given

Q: Q1) The shooter in position A throws a ball when the receiver is at the position B, as shown in…

Q: he object shown below is stable and floating in the water. Please select the correct option for the…

Q: 200 mm 40 mm 50 N 20 mm 300 N 160 mm 100 mm 120 N

A: given; force in negative x-direction(F1) (or) y-z plane =300Nforce in negative x-direction(F2) (or)…

Q: diameter as shown below indicates the piezometer readings with apparatus coefficient of 0.965. If…

A: Given Manometer reading, H = 55 - 15 = 40 mm Diameter, D = 36 mm d = 10.5 mm…

Q: Knowing that the central portion of the link BD has a uniform cross- sectional area of 800 mm²,…

Q: Q1) The shooter in position A throws a ball when the receiver is at the position B, as shown in…

Q: The area of a circle is increasing at a rate of 0.14π in²/s. If the area of the circle is 49π, what…

A: Given Increasing area rate, dA/dt = 0.14π in²/s Area, A = 49π…

Q: Q/Fluid at 15 bar is contained in a cylinder behind a piston, the initial volume being 0.01 m3.…

Q: Steam engine isentropically expands 8.019kg/s of steam from 0.68 MPa, 220 degree celcius. The…

Q: 3. The 10-cm long homogenous cone shown has a radius of 5 cm and a mass of 6 kg. Which of the…

Q: 5.103 The minimum pressure on a cylinder moving horizontally in water (T = 10°C) at 5 m/s at a depth…

Q: Q2) Consider a mass (m=5 kg) connected to a massless rod of length (L-2 m) to swing about point O,…

Q: The acceleration of a rocket traveling upward is given by a=(6+0.02s) m/s^2, where s is in meters.…

Q: Q1) The shooter in position A throws a ball when the receiver is at the position B, as shown in…

Q: The line used to show where a section view is cut is called A. a section line B. a hatch line…

A: An engineering drawing is a type of technical drawing which is used by thee industries to convey…

Q: The object shown below is stable and floating in the water. (1) Please match center of gravity cg,…

A: Centre of gravity = Point B

Q: Problem 1: What is the shear stress at point A if the internal shear, V, is 147 kN? 0.2 m 0.2 m 0.2…

A: Find the shear stress at point A.

Q: A jet of alcohol strikes the vertical plates shown in the Figure 2. A force F=425 N is required to…

Q: Velocity varies linearly with distance through the water nozzle shown below. Find the pressure…

A: Given Data The density of water is:ρ=62.4 lbm/ft3=1.94 slug/ft3 To find: The pressure gradient,…

Concept explainers

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P required to push the can into water to a depth of 8 in. Use =0.036lb/in.3 for water.
Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels are 16 ft on the upstream side and zero on the downstream side. For water, use =62.4lb/ft3.
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
A cylindrical object 83mm diameter, 154mm height and a mass of 594g, is placed in the tank, which contains oil(51mm thick) and water. Calculate the height(in mm) above the surface of the oil at which it will float if maintained in the vertical position. Take density of oil equals 974 kg/m3.
A cylindrical object 82mm diameter, 155mm height and a mass of 611g, is placed in the tank, which contains oil(51mm thick) and water. Calculate the height(in mm) above the surface of the oil at which it will float if maintained in the vertical position. Take density of oil equals 943 kg/m3. Answer: 32.4 mm
Calculate the weight of 10 kg block, when it is fulley submerged into the water?
The cylinder shown below is rotated about its centerline. Calculate the rotational speed, w, that is necessary for the water to just touch the origin, O, and the pressures at A and B.
right cylindrical object has a diameter of 1526 mm and a height of 2.1m. The density of water is 1000 kg/m3. If the right cylindrical object is placed in the water, what is the buoyant force?
Calculate the density of a body that floats in a liquid whose density is 8000KG/M3, knowing that it does so with 30% of its volume outside the liquid.
A cube 80 mm per side is made of a rigid foam material and floats in water with 60 mm of the cube below the surface. Calculate the magnitude and direction of the force required to hold it completely submerged in glycerine, which has a specific gravity of 1.26.
a solid glass sphere has a weight of 21.0 lbs in air and an apparent weight of 14.0 lbs when immersed in turpentine. when immersed in water the apparent weight is 11.6 lbs. calculate the specific gravity of the glass and that of the turpentine. find the density of each. PROVIDE SOLUTION, FORMULA, GIVEN, AND FBD
A triangular gate having a horizontal base 4 ft. long and an altitude of 6ft is inclined 45ofrom the horizontal with vertex pointing upward. The base of the gate is 8 ft below the surface of the liquid, which has a specific gravity of 0.82. What normal force, P must be applied at the vertex of the gate to open it, neglecting the weight of the gate.