A cylindrical object 83mm diameter, 154mm height and a mass of 594g, is placed oil(51mm thick) and water. Calculate the height(in mm) above the surface of the oil at which it will float if maintained in the vertical position. Take density of oil equals 974 kg/m3. the tank, which contains Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.

A cylindrical object 83mm diameter, 154mm height and a mass of 594g, is placed oil(51mm thick) and water. Calculate the height(in mm) above the surface of the oil at which it will float if maintained in the vertical position. Take density of oil equals 974 kg/m3. the tank, which contains Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Similar questions

A cylindrical object 82mm diameter, 165mm height and a mass of 599g, is placed in the tank, which contains oil(48mm thick) and water. Calculate the height(in mm) above the surface of the oil at which it will float if maintained in the vertical position. Take density of oil equals 966 kg/m3. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.
The Venturi meter shown in the sketch below, contracts the flow down to one quarter of its original area. Cold air at 0 deg C flows in the pipe through the Venturi meter. The velocity of the air upstream of the Venturi meter is equal to 40 ft/s and the pressure at the same point is equal to 30 psia. What is the manometer reading if the fluid of the manometer is water with density 1000 kg/m3 . Assume that the air behaves as an ideal gas with molecular weight equal to Mw=29 kg/kmol and constant density evaluated at upstream conditions. Use Bernoulli's equation for your calculations. please respond asap!
Suppose a liquid has a specific gravity of 6.28. If the measured pressure at the bottom of the tank in which it is stored is 83.58 psi, what is the height of the liquid in feet. answers need to be computed to two decimal places ; examples 6.45
1. In calibrating a 10-mL pipet, a measured volume of water was transferred to a tared flask and weighed, yielding a mass of 9.9814 g. (a) Calculate, with and without correcting for buoyancy, the volume of water delivered by the pipet. Assume that the density of water is 0.99707 g/cm3 and that the density of the weights is 8.40 g/cm3. (b) What are the absolute and relative errors introduced by failing to account for the effect of buoyancy? Is this a significant source of determinate error for the calibration of a pipet? Explain. 2. Repeat the questions in problem 1 for the case when a mass of 0.2500 g is measured for a solid that has a density of 2.50 g/cm3. 3. Is the failure to correct for buoyancy a constant or proportional source of determinate error?
PLEASE ANSWER QUESTION #1 ONLY, DISREGARD THE OTHER PROBLEMS GIVEN. SHOW COMPLETE SOLUTION. THANK YOU. An 8 ft diameter by 16 ft height vertical tank is receiving water (? = 62.5 lb/ft3) at the rate of 295 gal/min and discharging through a 4-in ID line with a constant speed of 6 fps. At a given instant, the tank is half full. Determine the following: QUESTION #1: the mass change in the tank (sample answer: 20,287.65 lb. round off to 2 decimal place QUESTION #2: the water level in the tank 15 min. later (sample answer: 20,287.65 ft round off to 2 decimal place QUESTION #3: the volume change in the tank (sample answer: 20,287.65 cu ft round off to 2 decimal place
A pressure in a given tank reads 381 mm of Hg. Determine the equivalent height of a certain fluid in m with sp.gr= 3.35. Round your answer to 2 decimal places.
The reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. If the tank is 30 cm. deep, and is contaminated with 3.05 cm. of water at the bottom, how many meters of air remains at the top when the gage indicates "FULL"? Use Unit weight of: gasoline = 6.24 kN/m3; air = 12.6 N/m3. The tank is closed. ANSWER : 0.017
A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 40 psi, determine the gage pressure of the gasoline line. Assume the unit weight of air to be 0.0765 lb/ft3.
Pitot PipeBy connecting a mercury pressure gauge to a vertical pipeline through which water is transmitted, speed measurement is performed with a pitot tube. Since the deviation from the pressure gauge column is 15 cm, calculate the speed of the water in the pipe. (Pmercury=13560 kg/m3, Pwater=1000 kg/m3) (Answer is V2=6.08 m/s)
A rectangular tank 5m long, 2m wide and 2 m high is filled with water to a depth of 1.5m. It is mounted on a truck and accelerated along its length. If acceleration, a = 4m/s2, how much water will be spilled out? Do not write any unit in your answer, use 3 decimal places. Unit of Ans is m3
An 8 ft diameter by 16 ft height vertical tank is receiving water (? = 62.5 lb/ft3) at the rate of 295 gal/min and discharging through a 4-in ID line with a constant speed of 6 fps. At a given instant, the tank is half full. Determine the following: QUESTION 1: the mass change in the tank (sample answer: 20,287.65 lb. round off to 2 decimal place
A pressure in a given tank reads 188 mm of Hg Determine the equivalent height of column of nectar (sp.gr. = 2.94) in mm. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: mm Decimal Places required in the final answer: 1