An 8 ft diameter by 16 ft height vertical tank is receiving water (? = 62.5 lb/ft3) at the rate of 295 gal/min and discharging through a 4-in ID line with a constant speed of 6 fps. At a given instant, the tank is half full. Determine the following: QUESTION 1: the mass change in the tank (sample answer: 20,287.65 lb. round off to 2 decimal place

An 8 ft diameter by 16 ft height vertical tank is receiving water (? = 62.5 lb/ft3) at the rate of 295 gal/min and discharging through a 4-in ID line with a constant speed of 6 fps. At a given instant, the tank is half full. Determine the following: QUESTION 1: the mass change in the tank (sample answer: 20,287.65 lb. round off to 2 decimal place

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 18P: Using the information given in Table 10.4, determine the ratio of local pressure and density to...

See similar textbooks

Similar questions

SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the pressure required to decrease the volume of the oil by 2%?
Using the information given in Table 10.4, determine the ratio of local pressure and density to sea-level values. Estimate the value of air density at the cruising altitude of most commercial airliners. Altitude (m) sealevel PPsealevel 0 (sea level) 1000 3000 5000 8000 10,000 12,000 14,000 15,000
PLEASE ANSWER QUESTION #1 ONLY, DISREGARD THE OTHER PROBLEMS GIVEN. SHOW COMPLETE SOLUTION. THANK YOU. An 8 ft diameter by 16 ft height vertical tank is receiving water (? = 62.5 lb/ft3) at the rate of 295 gal/min and discharging through a 4-in ID line with a constant speed of 6 fps. At a given instant, the tank is half full. Determine the following: QUESTION #1: the mass change in the tank (sample answer: 20,287.65 lb. round off to 2 decimal place QUESTION #2: the water level in the tank 15 min. later (sample answer: 20,287.65 ft round off to 2 decimal place QUESTION #3: the volume change in the tank (sample answer: 20,287.65 cu ft round off to 2 decimal place
Water flows through a pipe 25 mm in diameter at a velocity of 6 m/s. Determine whether the flow will be laminar or turbulent assuming that the dynamic viscosity of water is taken as1.30 × 10−3 kg/ms and its mass density as 1000 kg/m3. If oil of specific gravity 0.9 and dynamic viscosity 9.6 × 10−2 kg/ms is pumped through the same pipe, what type of flow will occur?
An open cylindrical tank 800mm in diameter and 2000mm high contains water to a depth of 1.6m. It is rotated about its vertical axis at 13 rad/s. How many liters of water are spilled? Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3
Suppose that one such tank is cylinder shaped, 50ft high with a radius of 20ft. If we assume that water is pumped out of the tank via a pipe directly on top of the tank and that the tank is filled to a depth of 30ft, how much work (in ft-lbs) would be done by a pump to empty the tank? You may take the density of water to be 62.4 lbs/ft3
A vertical cylindrical tank is 9 m high and 5 m in diameter. It is two thirds full of water and is rotated uniformly about its axis. How fast will it have to be rotated in order that 9 ?^3 of water will be spilled out? Unit of the Correct Answer: rpm Decimal Places required in the final answer: 1
Instead of a 0.9 cm diameter water pipe, a 2.3 cm diameter pipe was installed. 8.6 liters of water per second was obtained from the previous water pipe. How fast does the water come out of the new line in liters per second? Other aspects related to water pipes are assumed to remain unchanged.
1. In calibrating a 10-mL pipet, a measured volume of water was transferred to a tared flask and weighed, yielding a mass of 9.9814 g. (a) Calculate, with and without correcting for buoyancy, the volume of water delivered by the pipet. Assume that the density of water is 0.99707 g/cm3 and that the density of the weights is 8.40 g/cm3. (b) What are the absolute and relative errors introduced by failing to account for the effect of buoyancy? Is this a significant source of determinate error for the calibration of a pipet? Explain. 2. Repeat the questions in problem 1 for the case when a mass of 0.2500 g is measured for a solid that has a density of 2.50 g/cm3. 3. Is the failure to correct for buoyancy a constant or proportional source of determinate error?
An open cylindrical tank having a radius of 0.45 m. is filled with water at a depth of 0.68 m. If it is rotated about its vertical axis to a velocity of 103 rpm, what should be the height (in meters) so that no water will be spilled out? Round off to two decimal places.