A cylindrical pressure vessel has an internal diameter of 1600 mm and is subject to an internal fluid pressure of 30 bar. The plate is 15 mm thick with an ultimate tensile stress of 600 N/mm2. The efficiencies of the circumferential and longitudinal joints are 50 and 80 percent respectively. Determine the factor of safety.

A cylindrical pressure vessel has an internal diameter of 1600 mm and is subject to an internal fluid pressure of 30 bar. The plate is 15 mm thick with an ultimate tensile stress of 600 N/mm2. The efficiencies of the circumferential and longitudinal joints are 50 and 80 percent respectively. Determine the factor of safety.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Similar questions

A cylindrical pressure vessel has an inner diameter of 5 ft and a thickness of 3/4 in. The stress capacity of the pressure vessel is 25ksi. If a safety factor of 1.2 is required for the design, determine the maximum internal pressure (in psi) it can sustain. A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
A large water tank that has a capacity to carry 20,000 liters is to be supported by four cylindrical posts. These four support posts are made of plain carbon (1045) steels with the yield and tensile strengths of 310 MPa and 565 MPa, respectively. Determine the minimum required diameter of the post assuming a factor of safety of 5.
4. The compression load of 120 kN acts on the steel pipe of Table B-14. Determine the minimum Nominal dimeter pipe when the safety factor is 1.5 with a yield strength of 240MPa.
2. A cylindrical vessel has an internal diameter of 2 m. It is made of 15 mm thick plate. The efficiency of the longitudinal and circumferential joints are 80 % and 60 % respectively. If the ultimate tensile stress for the material is 500 MPa and the factor of safety is 6, determine the safe internal pressure to which the vessel may be subjected.
The cover of a cylindrical pressure vessel made of cast iron is shown in fig.1 The inner diameter of the cylinder is 500 mm and the internal pressure is limited to 2MPa. The cover is fixed to the cylinder by means of 16 bolts with a nominal diameter of 20 mm. Each bolt is initially tightened with a preload of 20 KN. The bolts are made of steel FeE250 (S yt = 250 N/ mm 2 ). Assume. E for steel = 207 KN/mm 2 ,E for cast iron = 100 KN/mm 2, E for Zinc = 90 KN/mm 2,Determine the factor of safety for bolts considering the effect of the gasket.
A spherical tank contains an internal pressure of 3.0 MPa, the diameter is 16 m, the yield stress is 490 MPa. and the factor of safety is 2.5. Determine the required thickness I to the nearest millimeter.
Compute the minimum vine diameter to provide a desired factor of safety of 1.7 against yield-type failure. Assume a yield stress of 300 MPa, and that the mass of the monkey is 65 kg. Hint Weight (N) = Mass (Kg) X g (9.81 m/s2)
Two rods are connected to each other and are restrained at top and bottom. The top portion is steel with modulus of elasticity equal to 200x10^3 MPa and coefficient of thermal expansion equal to 11.7x10^-6/C, the bottom is made up of brass with modulus of elasticity equal to 105x10^3 MPa coefficient of thermal expansion equal to 20.9x10^-6/"C. The temperaturé rose to 50°C from normal condition introducing stresses in the bar. Determine the force induced in the bar. Note: Final Answer in 4 decimal places.
A cylindrical pressure vessel with a diameter of 600 mm is to be fabricated from steel plates of thickness 16 mm. Compute the maximum value of the internal pressure it can hold inside if the tangential stress is limited to 140 MPa with a safety factor of 2.4. a. 4.28 MPa b. 5.28 MPa c. 3.11 MPa d. 6.09 MPa
A 20 mm thick flange coupling connects two shafts in order to transmit 250 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm located at a 210 mm bolt circle diameter. Determine the factor of safety based on compression between the bolt and flange. The yield point of the bolt is 450 MPa. A. 4.75 B. 3.75 C. 2.75 D. 5.75
A storage tank is 5m in diameter, 4m high and contains fluid with density of 795 kg/m^3. Determine the required wall thickness if the yield stress of the material is 325 MPa, the factor of safety is 10 and the efficiency of the longitudinal joint is 80%
1. A cylinder tankhas a maximum load of 2600 kg while the pressure is 2600 kpa. If the ultimate stress is 55 000 kpa and a factor of safety is 4.5, calculate the required wall thickness of the cylinder. Choose the correct answer below and show complete solution: a. 18.34 mm b. 14.38 mm c. 13.48 mm d. NOTC 2. A spherical tank has a diameter of 12 m, if the tangential stress of the tank is 18 Mpa, determine the maximum internal pressure of the tank can carry if the wall thickness is 25 cm. Choose the correct answer below and show complete solution: a. 150 kPa b. 15000 kPa c. 1500 kPa d. NOTC 3. A cylindrical tank has an inside diameter of 6-in and is subjected to an internal pressure of 600 psi. If the maximum stress is 1300 psi, calculate the required thickness. Choose the correct answer below and show complete solution: a. 0.1385 in. b. 0.3185 c. 0.8135 d. NOTC