Please help The cylinder of a four-stroke dieselengine has the following specifications:Cylinder boreMaximum gas pressure150 mmМахітит3.5 MPaCylinder material = Grey cast iron FG 200(S,= 200 N/mm2)Factor of safety = 5Poisson's ratio = 0.25Determine the thickness of the cylinder wall.Also, calculate the apparent and net circumferentialand longitudinal stresses in the cylinder wall.%3D

Given that ; The cylinder bore diameter is d=150 mm. The maximum gas pressure is Pmax=3.5 MPa.…

The cylinder of a four-stroke diesel engine has the following specifications: Cylinder bore 150 mm - Maximum gas pressure: - 3.5 MPa = Cylinder material Grey cast iron FG 200 (S = 200 N/mm²) Factor of safety = 5 Poisson's ratio = 0.25 Determine the thickness of the cylinder wall. Also, calculate the apparent and net circumferential and longitudinal stresses in the cylinder wall.

The cylinder of a four-stroke diesel engine has the following specifications: Cylinder bore 150 mm - Maximum gas pressure: - 3.5 MPa = Cylinder material Grey cast iron FG 200 (S = 200 N/mm²) Factor of safety = 5 Poisson's ratio = 0.25 Determine the thickness of the cylinder wall. Also, calculate the apparent and net circumferential and longitudinal stresses in the cylinder wall.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The shaft and the flange of a marine engine are to be designed for flange coupling, in which the flange is forged on the end of the shaft. The following particulars are to be considered in the design: Power of the engine=2.4 MW Speed of the engine 80 r.p.m Permissible shear stress in bolts and shaft = 60 MPa Number of bolts used =6 Pitch circle diameter of bolts=1.6* Dimeter of shaft Find 1.diameter of shaft; 2.diameter of bolts; 3.thickness of flange; and 4.diameter of flange. (25 degrea
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
A 19mm stud bolts is used to fastened on a 250 mm diameter cylinder head of diesel engine. If there are 10 stud bolts, determine the pressure inside the cylinder if bolt stress is 50 Mpa. A. 288.8 KPa B. 2888 KPa C. 3426 KPa D. 4828 Kpa Please solve the Problem elaborately and Refer Machine Elements and Stresses Equations from the figures or use other shortcut Methods you have or you may Solve both or in more different methods the better ?. Your solution will be use as reference for my Future Board Exam preparation/review/study. Thank you so much dear your work will be appreciated much and rated excellently.
An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which failswhen the shear stress is 160N/mm2.a) If the output shaft is solid, determine a suitable diameter to give a safety factor of three.b) If the shaft is hollow with an external diameter of 50mm, calculate a suitable internaldiameter to give a safety factor of three. Also, determine the percentage saving in weight.
The work cylinder of a hydraulic system is acted by a hydraulic pressure of 400 psi while the maximum load of the piston is 6000 lbs. if the allowable tensile stress is 2300 psi, what is the required wall thickness of the cylinder. a.0.510 in. b.0.448 in. c.0.420 in. d.0. 512 in.
A link of a valve gear has to be curved in one plane, for the sake of clearance. Estimate the maximum tensile and compressive stress in the link if the thrust is 2500 N. (Cam bridge) ANSWER: maximum tensile 38.0 MN/m2; maximum compressive 46.0 MNIm2. Please show the solution to get the answer.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
A semi-elliptic spring used for automobile suspension, consists of twoextra full-length leaves and eight graduated-length leaves, including themaster leaf. The centre-to-centre distance between the two eyes is 1 m.The leaves are made of steel 55Si2Mo90 (S = 1500 N/mm yt2 andE = 207 000 N/mm2) and the factor of safety is 2. The maximum springload is 30 kN. The leaves are pre-stressed so as to equalize stresses in allleaves under maximum load. Determine the dimensions of thecross-section of the leaves and the deflection at the end of the spring.
An AISI 1035 CD steel tube has an OD = 45 mm and a wall thickness of 5 mm. What maximum external pressure can this tube withstand if the largest principal normal stress is not to exceed 80 % of the minimum yield strength of the material? Assume ?? = 0.
In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft rotates at a speed of 679 rpm and transmits a power of 5 kW. If the maximum torque exceeds the mean torque by 23%. Take the value of allowable shear stress as 71 MPa. Find the value of the following i) Torque transmitted in N-m ii) Maximum torque transmitted in N-m iii) Diameter of the shaft in mm.
A semi-elliptic spring used for automobile suspension, consists of two extra full-length leaves and eight graduated-length leaves, including the master leaf. The centre-to centre distance between the two eyes is 1 m. The leaves are made of steel 55Si2Mo90 (Syt = 1500 N/mm2and E = 207000 N/mm2) and the factor of safety is 2. The maximum spring load is 30 kN. The leaves are pre- stressed so as to equalize stresses in all leaves under maximum load. Determine the dimensions of the cross-section of the leaves and the deflection at the end of the spring.