A cylindrical rod of steel (E = 207 GPa), 4mm in diameter is to be deformed by a tensile force. Determine the force (in N) that will produce an elastic reduction of 2.5 x 10-3mm in diameter if Poisson’s ratio is 0.30. Show complete solution and formulas used.

A cylindrical rod of steel (E = 207 GPa), 4mm in diameter is to be deformed by a tensile force. Determine the force (in N) that will produce an elastic reduction of 2.5 x 10-3mm in diameter if Poisson’s ratio is 0.30. Show complete solution and formulas used.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Figure P-251 A L= 5 ft L= 3 ft 2 ft 6000 4 ft 4 ft

Q: 2. A steel beam with the cross section is shown in the following figure. Calculate elastic and…

A: Given Data: The plastic moment of the cross-section is, Mp=150 kN-m The cross-section of the beam…

Q: - Find the value of lateral strain of a compressi testing machine whose cylinder diameter is 250 mm…

A: Given data- Cylinder diameter(D)=250 mmChange in diameter∆D=0.0150 mmYoung ModulusE=0.13×105 N/mm2…

Q: A 59 kN axial load is applied to a metal bar with a rectangular cross-section, 11 mm wide by 21 mm…

Q: A bar tapers from a diameter of 140 mm to a diameter of 80 mm over its length of 4 meters and is…

Q: An aluminum block show in Figure 9 is subjected to uniform pressure on all faces. If the chang ein…

Q: As shown in the figure, a nigid beam with negligible mass is pinned at one end and supported by two…

A: Let,Ts=Tension in the steel rodTA=Tension in the Aluminium rod R=reaction at hinge support,from FBD…

Q: Calculate the depth of compression block of the section in PART A in mm.0

Q: 2,650.25 meters when temperature was 15°C and the pull was 40N supported only at quarter points. The…

Q: In your solutions, determine the: 1. X component of the resultant force 2. Y component of the…

A: Consider the figure,

Q: bar of a certain material has 50 mm x 50 mm cross-section. When it is subjected to an axial pull of…

Q: As shown, three steel wires, each 27 mm2 in area, are used to lift a mass M. Their unstretched…

Q: The figure above is a skycam which is supported by 2 wires (assume that no wires holding at the top…

Q: Determine the value of stress if modulus of elasticity is 62 MPa and strain value is 0.0025

A: GIVEN: Modulus of Elasticity = 62 MPa Strain = 0.0025 TO CALCULATE: Stress CONCEPT: STRESS =…

Q: In this figure is a strut and a cable which was used to lift a body, if the strut and a cable has a…

A: we have to determine the value of maximum weight of the body according to the given data like we can…

Q: 1. A steel rod with a cross-sectional area of 140 mm? is placed between two fixed supports. The…

Q: 13. As shown in the figure, a homogeneous 100-kg rigid block is suspended by the three springs whose…

Q: Figure Q4 shows a structure with an applied load P at joint C. If the cross-sectional area and…

A: Solution: We will find load in each member by section method Section about AB…

Q: Three uniform 1-meter bars weighing "W" each are welded together as shown. The bars are suspended by…

A: Given: The length of the bars is 1 m. The tension at B is 250 N.

Q: A solid circular rod with a diameter of d = 19 mm is shown in the figure. The bar is made of an…

A: Given data: Diameter of the rod (D) = 19mm Modulus of elasticity of the aluminium (E) = 70 GPa = 70…

Q: 2.5 m 3.2 m (1) 0 m (2) 2.3 m B V P

Q: Determine the minimum cross-sectional area in in? of a steel bar required to support a tensile force…

A: Solution Given Data Tensile Force P= 68 kipsAllowable unit stress σallow= 30 ksi

Q: 2.83 Surface tension can be found by measuring the force to lift a plate: ↑ F W = weight w = width…

A: Using the free body diagram the value of surface tension can be evaluated. Knowing that surface…

Q: A bar of 30 mm diameter is tested in tension. It is observed that when a load of 80 kN is applied,…

A: Given data:

Q: 1. (a) A (110+X) mm long cylindrical rod is subjected to an axial tensile load of 110 kN, and a…

A: Determine, (i) shear stress, (ii) modulus of elasticity of the material(E).

Q: Determine the allowable value of force P (in Newtons), if a bar of diameter d = 31 mm and length L =…

Q: A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of P =…

A: Given data in question Load Diameter Length Change in Diameter To find out Elasticity modulus…

Q: 1- Consider the unit cube shown in the Figure, which undergoes the deformation: x₁ = α (X₁ X₂), x₂…

Q: 9. A 200 kgf load is applied to a steel bar of cross section area 6 cm?. When the same load is…

Q: For the loading situation given in the figure; a) Find the principal axes of inertia and show them…

A: O is the centroid of given cross section x and y are centroidal axis Ix=50×150312+50×150×12522×2…

Q: An arbitrary material has an elastic modulus of 118 GPa. How much tensile force was applied to a 100…

A: we have E = 118Gpa 100 mm long cylinder with 10 mm dia and redution in area = 0.1 % and poissons…

Q: How much will a steel rod lengthen under tension with the following considerations? The steel rod is…

Q: A line was found to be 2865.35 m long when measured with a 30-m tape under a steady pull of 6.5 kg…

A: Tm=30oC To=20oC L=2865.35m

Q: Instructions What is the minimum diameter of a solid steel shaft that will not twist through more…

Q: A 30m tape weighing 0.90kg has a cross-sectional area of 0.0485cm2. The tape measures 30m when…

A: Given information: Length of the tape, L = 30 m Weight of the steel tape, W = 0.90 kg. Cross…

Q: Example 8.3 A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150…

A: Given data Diameter of speciment (D) = 12 mm Gauge length (L) = 150 mm Twisting moment (T) = 10 N…

Q: The simply supported beam given in the figure is 8-meter-long and loaded with a uniformly…

A: It is required to determine the maximum bending moment. Mmax=wL28=15 kNm×1000 N1 kN×8 m28=120×103…

Q: A beam with circular cross-section and diameter of D = 273 mm is subjected to a bending moment about…

A: Using formula:σ=MyII=πd464y=d2

Q: A 20-cm-diameter steel rod is subjected to a tensile load of 1000KN at one end and is fixed at the…

Q: A steel bar with a thickness 5 mm is to carry a load of 2000 N. Using the direct method, determine…

A: Given Data: Thickness of the steel bar is t=5 mm. Load T=2000 N. Modulus of elasticity is E=200 GPa.…

Q: Determine the allowable value of force P (in Newtons), if a bar of diameter d = 29 mm and length L =…

Q: A rod of diameter 50 cm and length 6 m is hanging vertically and carries an axial load of 10 kN at…

A: Given:- The diameter of the rod = 50 cm = 0.5 m The length of the rod = 6 m The magnitude of an…

Q: SHOW COMPLETE ANSWER AND ILLUSTRATION FINAL ANSWER IN 3 DECIMAL PLACES Problem 4: A steel bar 50…

Q: A steel tape is 100 m long at a temperature of 20°C and a pull of 10 kg. It was used to measure a…

Q: The strain components & & and Yxy are given for a point in a body subjected to plane strain.…

A: In the analytical method strain at any plane located at an angle Ꝋ with the given plane can be…

Q: 4 m 450 mm B 50 mn 50 mn 350 mm 50 mm Figure la Figure Ib Before a diver jumps into the water,…

Q: 6. The system of knotted cords shown in figure below support the indicated weights. Compute the…

A: First step Draw free body diagram of the whole system remove all support with external tension on…

Q: Q 2. For the symmetrical section in figure 2 shown below, calculate B mm 350 mm 0.8 B mm Figure (2)…

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

A: We will draw Free Body Diagram for each section.

Q: An elastic cube prism has dimension of a=200 mm is placed in two rigid plates as shown in the…

Question

A cylindrical rod of steel (E = 207 GPa),
4mm in diameter is to be deformed by a
tensile force. Determine the force (in N)
that will produce an elastic reduction of
2.5 x 10-3mm in diameter if Poisson’s
ratio is 0.30.

Show complete solution and formulas used.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (D= 2.25" and d=0.90''). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12x106 psi, 4x106 psi, and 6x106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft.
A conductor with a specific gravity of 40.10-3 kg/m.mm2 was drawn between two poles, which are given in the figure and erected on a valley slope, with a tension of 10 kg/mm2. Accordingly, find the conductor stress at the high suspension point. Please answer in very short i will like.. Please answer short and dont reject
A rod with a diameter of 13 mm and a length of 50 mm is subjected to a force of 50 kN. The diameter is reduced to 12.99265 mm. Determine: a. The modulus of elasticity. Answer: 200 GPa. b. Poisson's ratio. Answer: ν = 0.30 c. Shear modulus. Answer: G = 76.92 GPa. d. The deformation of the rod. Answer: δx = 0.09415 mm. Recommendation: Obtain the modulus of elasticity using the slope of the straight line.
The Bulk Modulus of Elasticity of water us approximately 300 000 psi. If the temperature is 60°F, determine the pressure that should be applied so that the ratio of the change of volume with its initial is 2.5%. Use ?? = − dP/ dV/ V and 2 decimal places.
Two solid cylindrical rods 1 and 2 are joined together at metal plate B loaded. If the normal stress in each rod is limited to 40 ksi, determine the minimum diameter for each rod (in inches). Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
A square plastic bar (length Lp, side dimension sp = 193 mm) is inserted inside a hollow, square, cast iron tube (length Lc = 400 mm, side sc = 200 mm, and thickness tc = 3mm). (a) What is the required initial length Lp of the plastic bar so that, when it is compressed by some force P, the final length of bar and tube are equal to legnth Lc, and, at the same time, the gap between plastic bar and cast iron tube is closed? (b) Compare initial and final volumes for the plastic bar. Assume that Ec = 170 GPa, Ep = 2.1 GPa, vc = 0.3, and vp = 0.4.
CALCULATE THE FEM FORMULA OF THE GIVEN FIGURE USING THE FORCE METHOD. Please show a complete solution.
Hi, I need help with this question please. Thank you. A cantilever thin-walled cylindrical tube of inner diameter ? = 30cm and thickness ? = 1cm is subjected to a torque T and internal pressure p as shown below. The free end of the tube is closed. Strain gauges A and B mounted on the surface of the cylinder give readings ?? = 7.5 × 10^−6 and ?b = 19.7x10^−6, respectively. The bar is made of steel having Young's modulus E=200 GPa and Poisson's ration ? = 0.3. a) Determine the torque, T, and internal pressure, p. b) Determine the absolute maximum shear strain ???? at point C.
A rod of diameter 50 cm and length 6 m is hanging vertically and carries an axial loadof 10 kN at bottom end. Calculate the elongation of the bar at a distance 2 m from thebottom end. Take the unit weight of the rod material is 25 kN/m' and modulus ofelasticity of the material is 3x109 MPa.
Block A has a mass of 100 kg and the coefficient of friction is 0.20. Determine the friction force between A and B. Please answer the question with FBD and the solution. Thank you.
At the limit of proportionality, a bar 30 mm wide (w) and 12 mm thick (t) elongates 2.0 mm under an axial load of 41.5 kN. The bar is 1.5 m long. If the Poisson's coefficient of the material is 0.33, determine: (a) the modulus of elasticity. E = ? (b) the variation in width. dw = ? (c) variation in thickness. dt = ?
A cylindrical rod having a diameter of 0.5in is subjected to tension. How much load is required to cause a 10-4in change in the diameter. Take Young’s modulus of rod as 11x106 psi and Poisson’s ratio as 0.33.