Please correct answer otherwise dislike An aluminum block show in Figure 9 is subjected to uniform pressure on all faces. If the changein length on edge AB is –1.2 x 10-3in., what is:a. the change in length of the other two edges,.b. the pressure, p, applied to the faces of the block. Assume E =0.29.29 x 106 psi and v =in.4 in.Figure 9.

Answered: Image /qna-images/answer/160747b9-7237-4845-a70c-7e122b073c4c.jpg

An aluminum block show in Figure 9 is subjected to uniform pressure on all faces. If the chang ein length on edge AB is –1.2 x 10-³in., what is: a. the change in length of the other two edges, 29 x 106 psi and v = b. the pressure, p, applied to the faces of the block. Assume E 0.29. 2 in. Figure 9.

An aluminum block show in Figure 9 is subjected to uniform pressure on all faces. If the chang ein length on edge AB is –1.2 x 10-³in., what is: a. the change in length of the other two edges, 29 x 106 psi and v = b. the pressure, p, applied to the faces of the block. Assume E 0.29. 2 in. Figure 9.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. where P=25 .
The Bulk Modulus of Elasticity of water us approximately 300 000 psi. If the temperature is 60°F, determine the pressure that should be applied so that the ratio of the change of volume with its initial is 2.5%. Use ?? = − dP/ dV/ V and 2 decimal places.
The Bulk Modulus of Elasticity of water us approximately 300 000 psi. If the temperature is 60°F, determine the pressure that should be applied so that the ratio of the change of volume with its initial is 2.5%. Use EB = − dP/dV/V and 2 decimal places.
A closed cylindrical tank, placed horizontally, 400 mm in internal diameter and 2.2 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure.a. What is the magnitude of the internal pressure in MPa?b. What is the applied axial force in kN? (detailed solution please)
A bar 4 ft long is set snugly between two rigid walls when the temperature is 50deg.F. What is the stress in the bar when the temperature is 90deg.F? Use E = 17 x10^6 psi, coef. of thermal expansion = 9.3 x10^-6 per deg.F a. 6520 psib. 6324 psic. 6156 psid. 6572 psi
Q.2 Three bars each made of different materials are connected together and placed between two walls when the temperature is T1 = 12 oC. Determine the force exerted on the rigid supports when the temperature becomes T2=18 oC. The material properties and crosssectional area of each bar are given in the figure.
write legibly and indicate all necessary FBDs, concepts andformulas needed in the solution. Show the derivation of the girth and longitudinal stresses of the thin-walled cylindrical container shownbelow. Say p is the internal pressure, d is the inside diameter of the container, and t is wall thickness. See figure 103.
An aluminum extrusion has the shape shown in the figure where b= 38 mm, d= 52 mm, a= 10 mm, and t= 2 mm. A vertical shear force of V= 2500 N acts on the cross section. Determine the shear flow that acts in the shape at points A–D. Part 1 Break the cross section into five rectangular areas, as shown. Find the area A1 of area (1) and the vertical distance y1 from the bottom edge of the cross-section to the centroid of area (1). Similarly, find the areas of the other four rectangles, and the vertical distance from the bottom edge of the cross section to the centroid of each. A1= 104 mm2 A2=A3= 20 mm2 A4=A5= 32 mm2 y1= 26 mm y2=y3= 5 mm y4=y5= 1 mm Part 2 Find y¯, the vertical distance from the bottom edge of the cross section to the centroid of the cross section. y¯= 14.27 mm Part 3 Find Iz, the area moment of inertia about the z centroidal axis for the cross-section. Iz=…
From the figure shown, Determine: The plastic section modulus about the horizontal axis. x10^6 mm^3 (3 decimal places)
The BC rod in the carrier system shown in the figure has a circular cross section. diameter 25 mm and Tensile Strength 210 MPa and Modulus of Elasticity 2x105 It is MPa. Since a load of 640 kg is hung on the D end of the system; For BC bar: a) Tensile stress, b) Safety coefficient, c) Calculate the length change amount.
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P is equal to 51kips)
A line was found to be 2865.35 m long when measured with a 30-m tape under a steady pull of 6.5 kg at a mean temperature of 30°C. Determine the correct length of the line if the tape used is of standard length at 20°C under a pull of 5.5 kg. Assume the cross-sectional area of tape to be 0.025 cm2 , coefficient of thermal expansion to be 0.0000116/1°C and the modulus of elasticity of steel is 2.0 x 106 kg/cm2..