A cylindrical shell made of mild steel plate of 100 cmdiameter is to be subjected to an internal pressure of 10kg/em?. If the m aterial yields at 2000 kg/em2, assumingfactor of safety as four and using maximum principal stresstheory, thickness of the plate will beA.5 mmB.10 mmC.15 mmD. 20 m m

Given data- A cylindrical shell-Diameter of steel plate (D) = 100 cmInternal pressure (P) = 10…

A cylindrical shell made of mild steel plate of 100 cm diameter is to be subjected to an internal pressure of 10 kg/em2. If the material yields at 2000 kg/cm?, assuming factor of safety as four and using maximum principal stress theory, thickness of the plate will be A. 5 mm B. 10 mm C. 15 mm D. 20 mm

A cylindrical shell made of mild steel plate of 100 cm diameter is to be subjected to an internal pressure of 10 kg/em2. If the material yields at 2000 kg/cm?, assuming factor of safety as four and using maximum principal stress theory, thickness of the plate will be A. 5 mm B. 10 mm C. 15 mm D. 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the minimum diameter of cylindrical vessel made of 1-inch thick materials that is use to carry a gas at a pressure of 1500psi. The stress is limited to 12ksi.
A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN. Determine the smallest allowable outside diameter of the tube if the working stress is 110 MN/m^2.
Q4) two plate one lower fixed and one upper moved with a velocity 0.3 m/s , thedistance between the two plate is 0.3 mm and viscosity of the liquid is 0.65*10-3kg/m.s , calculate the shear stress on the upper plate .
a) Determine the zero-effort frame by justifying with a table asfollow Joint in equilibrium Nul stress frame .
A shaft 12 mm in diameter and 600 mm long between long bearings carries a central mass of 4 kg.If the centre of gravity of the mass is 0.2 mm from the axis of the shaft, compute the maximumflexural stress in the shaft when it is running at 90 per cent of its critical speed. The value of Young’s modulus of the material of the shaft is 200 GN/m2
1. A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN. The compression of the rod is 1.35 mm, and its diameter becomes 30.015 mm. Determine the modulus of elasticity (MPa) of the material. Assume the material does not yield. 2. Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a pressure of 1300 psi. The diameter of the vessel is 2 ft, and the stress is limited to 13 ksi.
A cylindrical tank has an internal pressure of 1.5Mpa. - Determine the diameter of the cylindrical tank if the strenght per meter of longitudinal joint is 480KN - Determine the diameter of cylindrical tank due to strenght of girth joint of 200KN -Determine the minimum thickness of the cylindrical tank if the stress is limited to 40Mpa
A large uniform cylindrical steel rod of density ρ = 8.8 g/cm3 is 4.0 m long and has a diameter of 5.0 cm. The rod is fastened to a concrete floor with its long axis vertical. What is the normal stress in the rod at the cross section located at (a) 2.0 m from its lower end? (b) 2.5m from the lower end? Your answer
A water tank, 22 ft in diameter, is made from steel plates that are 1/2 in. thick. Find the circumferential stress, if the maximum height of the tank is 52.45 ft. The specific weight of water is 62.4 lb/ft3.
A hollow circular column of internal diameter 20 mm and external diameter 40 mm has a total length of 5m. One end of the column is fixed, and the other end is hinged. Find out the crippling stress of the column if E = 2 × 10^5 N/mm2. Also, find out the shortest length of this column for which Euler’s formula is valid taking the yield stress equal to 250 N/mm2.
A closed cylindrical tank containing a pressurized fluid has an outside diameter of 448 mm and a wall thickness of 11 mm. The tank is pressurized to 2.53 MPa. Determine the hoop stress in the wall of the tank. Round off the final answer to five decimal places.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion? Given data: -The yield strength of the pressure vessel is σy = 250 MPa.The inner diameter of the vessel is d = 2 m.The pressure acting in the vessel is P = 10 Atm.The longitudinal Stress is σL = 200 MPa.Hoop Stress σθ = 150 MPaThe Radial Stress is σR = -50 MPa.