A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 4.5 MN/m2. Set up the equations of stress that is required to solve the problem. 2. Calculate the stresses in the steel vessel.

A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 4.5 MN/m2. Set up the equations of stress that is required to solve the problem. 2. Calculate the stresses in the steel vessel.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Related questions

Q: The cylindrical portion of the propane tank has an outer diameter of 12 in. and a wall thickness of…

Q: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected…

Q: A steel tube of 200 mm external diameter is to be shrunk onto another steel tube of 60 mm internal…

A: For inner tube: Write the expressions for A and B for thick cylinder. At r=0.030,…

Q: A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is…

Q: A steel tube of 300 mm external diameter is to be shrunk on to another steel tube of 90 mm internal…

A: Given data: External diameter, d3 = 300 mm, r3 = 150 mm Internal diameter, d1 = 90 mm, r1 = 45 mm…

Q: 2. A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is…

A: Given data: Diameter of the cylindrical pressure, D=400mm Thickness of the wall, t=20mm Internal…

Q: A steel cylinder of 1 metre diameter is carrying a fluid under a pressure of 10 N/mm2. Calculate the…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: For the following data, using the stress-transformation equations. (a) find the principal stresses…

A: Given Data 20 -20-20 -10 To find (a) find the principal stresses and show their sense…

Q: Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane…

A: Given details:Es=205GPaEc=100GPadiameter of rod = 20mm

Q: the associated normal stresses and show the results

Q: A 1.25 inch diameter hole is drilled on the centerline of a steel bar 3.5 inches wide by 3/8 inches…

A: The data given is, The diameter of the drilled hole, D = 1.25 in. Width of steel bar = 3.5 in. The…

Q: A cylindrical steel pressure vessel 400 mm in diameter with a subjected to an internal pressure of…

A: Givendia=400mmthickness t=20mmInternal pressure P=4.5MN/m2

Q: A thin cylinder of 100 mm internal diameter and 5 mm thickness is subjected to an internal pressure…

A: Given:internal diameter, di=100 mm or 0.1mthickness, t=5 mm or 0.005 mouter diameter, do=110 mm

Q: A steel gas bottle 2 m long with a diameter of 250 mm and a 3 mm wall thickness is pressurized to 3…

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

Q: is a 150 mm long rectangular plate (thickness 10 mm and height 70mm). There are two circular notches…

Q: Find the longitudinal stress in the tank.

A: To Find the longitudinal stress.

Q: A thin cylinder of 100 mm internal diameter and 5 mm thickness is subjected to an internal pressure…

A: Introduction: Internal pressure causes a hoop and longitudinal tension in a thin-walled tube or…

Q: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected…

A: Given:Pressure, P=7.875 MPadiameter, d=400 mmthickness, t=20 mm

Q: A cylindrical pressure vessel has an internal diameter of 2 m and is fabricated from plates 20 mm…

Q: circular rod of 50 mm diameter experience a tensile load of 100 N. Find the stress induced in ro

A: Given:Diameter of rod, d=50 mmTensile load, L=100 N

Q: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected…

A: Diameter of the cylindrical steel pressure vessel, D=400 mm=0.4 mWall thickness of cylindrical steel…

Q: A thin cylinder of 100 mm internal diameter and 5 mm thickness is subjected to an internal pressure…

Q: The internal and external diameter of a thick hollow cylinder are 105 mm and 145 mm respectively. It…

A: According to Lame's equation - σ = Bx2-AGiven -σ = 120 Nmm2 at x = 52.5 mm σ = 40 Nmm2 at x = 72.5…

Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…

A: Given data: - The pressure inside vessel is P = 150 psi. The length of the vessel is L ft. The…

Q: A steel bar with triangular cross section has a base 30 mm and height 20 mm. When 1.2kN force…

A: Stress developed in the bar = Force applied/area of Cross section.

Q: Define the main difference between thick and thin cylinders and give an example for each type of…

Q: Show the derivation of the girth and longitudinal stresses of the thin-walled cylindrical container…

Q: 0 kN. Determine the required cross-sectional area of the wable stresses are 6 MPa for concrete and…

A: Need to determine the cross-Sectional area of reinforcing steel

Q: The wall thickness of a spherical thank is 8mm, calculate the diameter if allowable stress is 140MPa…

Q: A steel rod of 25 mm diameter is fitted inside a brass tube of 25 mm internal diameter and 375 mm…

Q: Consider a tetrahedron containing point Q and show the forces on the faces of the tetrahedron due to…

Q: (320) mm inside diameter and (64) mm thickness is subjected to an internal pressure of 15 MPa. Find…

Q: A shaft 450 mm diameter supports a 15000 kg steel propeller of the ship. The propeller shaft can be…

A: GIVEN: 450 mm =diameter mass=15000 kg 2 m =length N=100 rpm speed of the ship = 17.2 Knots…

Q: A steel bolt 8mm diameter fits loosely inside aluminium tube 8mm diameter and 16 mm outside diameter…

A: Diameter of steel rod=8 mmInside dia. of Aluminium tube=8mmOuter dia. of Aluminium…

Q: Two parallel shafts whose centers are 10 meters apart are connected by an open belt drive with a…

A: Given Data The distance between the shaft is: x=10 m The diameter of the larger pulley is: d1=1000…

Q: The state of stress shown below is from the surface of a bar under axial and torsion loading.…

A: Given data: The value of stress in x-direction is, σx=60 MPa. The value of stress in y-direction…

Q: A 30 mm square is drawn on the rim of a large steel pressure vessel. The biaxial stress situation in…

Q: . The solid rod shown below has a diameter of 25 mm. Calculate the stresses that act at points A and…

A: For the given loading diagrams, Calculate the moment of inertia, Z=π64d4Z=π64254Z=19174.76 mm4…

Q: A bearing supports a 28mm diameter solid steel torsion rod (plan view shown in Fig. 1) rigidly…

A: Theories of failure are compulsory to determine the safe dimension of a component under a bi-axial…

Q: A steel bar carrying 3000kN load,F, is attached to a support by a round pin 0.3m in diameter.…

A: Given data: The magnitude of the load, F = 3000 kN. The diameter of the pin, d = 0.3 m. Calculate…

Q: a shaft 80mm diameter transmits power at maximum shear stress of 63 mpa. find the length of 20mm…

A: given; →diameter(d)=80mm→for power transmission on shaft shear…

Q: 1. Can you treat this cylinder as Thin-Walled Cylinder? Prove that? 2. Calculate the tangential and…

A: Stress: Stress is nothing but force per unit area. It is represented by σ & the SI unit of…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 4.5 MN/m2.

Set up the equations of stress that is required to solve the problem.

2. Calculate the stresses in the steel vessel.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The wall thickness of a 1.2 m diameter spherical tank is 1.6875 mm. Calculate the allowable internal pressure if the stress is limited to 55 MPa. If i will get the same answer again I will report and downvote.
A steel gas bottle 2 m long with a diameter of 250 mm and a 3 mm wall thickness is pressurized to 3 MPa. Determine the stresses. help plz
A cylindrical steel pressure vessel 60 cm in diameter with a wall thickness of 30 mun, is subjected to an internal pressure of 6 Nmm. (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 200 MN/m?
A 6-inch diameter pulley mounted on a 2-inch shaft as shown transmits 9 kW at 1000 rpm. What is the combined stress acting on the shaft?
A cylindrical pressure vessel has an internal diameter of 2 m and is fabricated from plates 20 mm thick. If the pressure inside the vessel is 1.5 N/mm2 and in addition, the vessel is subjected to an axial compressive load of 2500 kN, calculate the normal and shear stresses on a plane inclined at an angle of 60⁰ to the axis of the vessel.
The internal and external diameter of a thick hollow cylinder are 105 mm and 145 mm respectively. It is subjected to an external pressure of 40 N/mm2 and an internal pressure of 120 N/mm2. Calculate the radial and circumferential stresses at the mean radius.
Calculate the diameter of a pressure vessel of thickness 0.04 m and the inside pressure is 20 mpa. Assume the permissible stress of the vessel is 100 mpa.
A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 144 lbs is applied at the end of a 1.1 ft lever arm, causing the pipe to twist. What is the maximum stress in the pipe in psi?
A rectangular block of material is subjected to a tensile stress of 90 N/mm2 along X axis and acompressive stress of 45 N/mm2 on a plane at right angle to it, together with shear stresses of80 N/mm2 on the same plane. Calculate the direction of principal planes, the magnitude ofprincipal stresses and the magnitude of greatest shear stresses.
The wall thickness of the spherical tank is 8mm, calculate the diameter if the allowable stress is 140 MPa and the internal pressure is 60MPa.
A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa.Calculate the tangential stress in the steel.
A steel tube of 300 mm external diameter is to be shrunk on to another steel tube of 90 mm internal diameter. After the diameter at the junction is 180 mm. Before shrinking on the difference at the junction is 0.12 mm. Find (i) The radial pressure at the junction; (ii) The circumferential stresses developed in the two tubes after shrinking on.