A cylindrical steel shaft is required to transmit a bending moment of 1000 Nm and a torque of 2200 Nm with a safety factor against yielding of 3. If the steel has a yield stress of 250 MPa, find the minimum permissible diameter for the shaft. Use von Mises’ theory of yielding.

A cylindrical steel shaft is required to transmit a bending moment of 1000 Nm and a torque of 2200 Nm with a safety factor against yielding of 3. If the steel has a yield stress of 250 MPa, find the minimum permissible diameter for the shaft. Use von Mises’ theory of yielding.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.4P: The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft...

See similar textbooks

Related questions

Q: Homework 2 H.W//Draw shear force and bending moment diagrams by using graphical method for the…

A: Draw shear force and bending moment diagrams by using graphical method for the following beams.

Q: Question: A spherical balloon containing Oxygen (initially at sea level) has a diameter of 8 in. If…

A: Given data with variables. At sea levelThe diameter of ballon d=8 indensity of air ρ=0.07498…

Q: Freehand sketch a set of front/top/right views

A: According to the given data A 3D object is given We need to draw Three projection view of the object…

Q: Pls answer asap I will give good ratings A jet of water flows from left to right and hits a…

A: U1=1.6 m/sA1=?U2=0.7 m/sA2=11 cm2θ2=35oU3=0.9 m/sA3=14 cm2θ3=25oρ=1000 kg/m3

Q: Draw the structure of the idealized modulus-temperature for thermoplastic and thermosetscurveand…

A: Thermosets and thermoplastics are two types of polymers that differ in their molecular structure and…

Q: P6-18 Air flowing at 0.5 m³/min enters à compres kPa and 25°C. The air exits at 600 kPa and 300°C.…

A: Air flow rate = 0.5 m3/min =0.00833m3/s At entry pressure = 101 kPa At entry Temperature = 25°C=…

Q: Water flows into a tank and out through another pipe, as shown in the figure below. The water in the…

A: Given:Surface area, Asurf=5.6 m2Inclination angle of door, θ=25oLength of the door, L=1.1 mWidth of…

Q: need solutions for DE,BD,AD

A: Given data is

Q: Acar (mass-1130 kg) is traveling at 32.5 m/s when it collides head-on with a sport utility vehicle…

A: GivenmA=1130kgVA=32.5 m/smB=2440 kg

Q: = 20 rad/ When the gear makes 29 revolutions, it reaches an angular velocity of w s, starting from…

Q: If the element shown is equilibrium F1-552 N, F2-381 N, a-30, B-43", a-0.32 m, b-0.19 m, and c-0.19…

Q: mawiali, Bmax Bmax √2 2.4 2.2 2 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0.4 0.6 0.8 1 wo 1.2 The Bandwidth…

A: Vibrate with a specific frequency is the property of mechanical systems and charged particles. This…

Q: The system is released from rest in the position shown. Calculate the tension T in the cord and the…

A: GivenmA=14 kgmB=23 kgμ=μk=μs=0.31

Q: Required information A 170-lb man A and a 40-lb child Care at the opposite ends of a 250-lb floating…

A: The mass of man A is ma=170 lb. The mass of child C is mc=40 lb. The mass of the boat is M=250 lb.…

Q: Please select all standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in.. 7.80…

A: The standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in. are: 7.80 in. 7.95 in.…

Q: Determine the maximum compressive force developed in member BG of side truss due to the right side…

A: The load acting on left to right wheel are 2, 4 and 1.4 kN. The horizontal length of the member is 3…

Q: Q2/ The peak load on a power plant is 60 MW. The loads having maximum demands of 30 MW, 20 MW, 10 MW…

A: Power plant is a facility where we generate electricity using fossil fuels like coals, natural gas,…

Q: A solid stainless steel [G = 12,500 ksi] shaft that is 30 in. long will be subjected to a pure…

Q: The stress in thin-walled sphere is greater than the thin-walled cylinder. (A) True (B) False

A: □ The following types of stresses are generated in case of the thin-walled pressure vessel: ▪︎…

Q: In the diagram below, m is an external mass applied to the Truss. Given the information provided in…

A: In the diagram below, m is an external mass applied to the Truss. Given the information provided in…

Q: Water is stored in a pressurised container at a height HT= 8.4 m. It then moves through a horizontal…

Q: 20. A steel shaft is transmitting 50 hp at 1,200 rpm. The nature of the load and type of service of…

A: Given data Power= 50hp Speed = 1200rpm Stress = 4000(psi) Find the torsional deflection at the…

Q: Using the method of joints, determine the forces in all members of the truss below and indicate…

Q: straight ladder to the wall? a. one-fourth the working height of the ladder b. one-half the height…

A: straight ladder to the wall? a. one-fourth the working height of the ladder b. one-half the height…

Q: A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load,…

A: Tensile force (P)=100 kN Original diameter (do)=0.02 m Original length (Lo)=2 m Final diameter…

Q: 7-104 An air conditioner with refrigerant-134a as the working fluid is used to keep a room at 23°C…

Q: Problem 2. Two projectiles are fired at the same instant, projectile A is launched horizontally with…

A: VA=12 m/sy=6mx=6mVBo=?

Q: The beam structure under loading will most likely experience internal shear forces and internal…

A: The beam structure under loading will most likely experience internal shear forces and internal…

Q: 4. y| 9 kN-m Im 18 kN/m B 3m C

A: To Find : The shear and bending moment diagram. The Free body Diagram : The F.B.D is,

Q: If the motor of the electric drill turns the armature shaft S with an angular velocity of w = (80t…

A: the angular velocity ω=80t12to find ω when N=220 rev

Q: An opaque surface with the prescribed spectral, hemispherical reflectivity distribution is subjected…

Q: A rectangular metal test specimen has a width of 11 48mm and a thickness of 1:12mm. Determine the…

A: Width of test specimen, w =11.48 mm Thickness of test specimen, t = 1.12 mm Tensile force, F = 2367…

Q: Show that if the atmosphere is isothermal, the temperature change of a parcel of air rising…

Q: A rotary engine is running at 7,200 rev/min when it runs out of fuel, causing the engine to…

Q: A solid 1.08-in.-diameter steel [G= 9500 ksi] shaft is subjected to the torques shown. Determine the…

Q: The system is released from rest in the position shown. Calculate the tension T in the cord and the…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: Learning Goal: To be able to find the center of gravity, the center of mass, and the centroid of a…

Q: H.W//Draw shear force and bending moment diagrams by using graphical method for the following beams.

Q: In a turbulent flow in a 0.3 m pipe the centerline velocity is 6 m/s, and that 50 mm from the pipe…

A: Given:Type of flow= TurbulentPipe diameter, d=0.3 mCenterline velocity, umax=6 m/s…

Q: 446 CHAPTER 17 17-102. The slender, 200-kg beam is suspended by a cable at its end as shown. If a…

Q: Just after the fan is turned on, the motor gives the blade an angular acceleration α= (20e-0.6t)…

A: Angular acceleration Alpha = 20e(-0.6t) (rad/s^2) Time = 9sec

Q: In a typical fuselage or wing section, the stringers and spars would carry most of the mainly…

A: The stringers and spars are the axial member in the fuselage and used to resists bending . As…

Q: What is the desired nozzle tip output to the nearest hundredth to deliver 10 gpa with equipment that…

A: Given: The value of gallons per acre is GPA=10. The value of ground speed miles per hour MPH=12. The…

Q: a) A control engineer has modelled the suspension system of a new model car using a 2nd order…

A: Given Data: (a) Gs=0.001s2+12s+81 To Find: (1) The natural frequency. (2) The damping ratio. (3)…

Q: The task is to parachute supply of 120 kg that includes the containing circular cylinder case of…

A: Given : The diameter of the hemisphere , D=0.4 m

Q: A plate of unidirectional Scotchply 1002 Glass/Epoxy (E = 38.6 GPa, v = 0.26) has the dimensions…

A: Given data is

Q: 12 ft 5 kips Koo. 3 ft

A: Given data:- To find:- the moment at the fixed support A

Q: 8. what is the magnitude of maximum stress that exists at the tip of an internal crack having radius…

A: Given:Radius of curvature of the crack, ρt=1.9*10-4 mmCrack length, a=3.8*10-2 mmThe nominal applied…

Q: QUESTION 3 Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and…

A: input speed, N1 = 1750 rpm output speed, N2 = 725 rpm linear velocity, v = 4000 ft/min

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data.

VIEW

Step 2: Calculations for diameter of the shaft.

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A solid copper bar of circular cross section has length L = 1.25 m and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 250 N · m torque acting at the ends. If the allowable shear stress is 30 M Pa and the allowable angle of twist between the ends is 2.5°, what is the minimum required diameter?
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
A solid circular bar A BCD with fixed supports at ends A and D is acted upon by two equal and oppositely directed torques T0, as shown in the figure. The torques arc applied at points B and C each of which is located at distance x from one end of the bar. (The distance x may vary from zero to L/2.) For what distance x will the angle of twist at points B and C be a maximum? What is the corresponding angle of twist 0max?
A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing maching until the applied torque reaches the value T = 500 N ·. At this value of torque, a strain gage oriented at 45º to the axis of the bar gives a reading e = 339 × 10-6. What is the shear modulus G of the material?
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.