A cylindrical tank with a large diameter is filled with water to a depth D = 0.419 m. A hole of cross-sectional area A = 5.18 cm2 in the bottom of the tank allows water to drain out. (a) What is the rate at which water flows out, in cubic meters per second? (b) At what distance below the bottom of the tank is the cross-sectional area of the stream equal to one-half the area of the hole? (a) Number Units (b) Number Units

A cylindrical tank with a large diameter is filled with water to a depth D = 0.419 m. A hole of cross-sectional area A = 5.18 cm2 in the bottom of the tank allows water to drain out. (a) What is the rate at which water flows out, in cubic meters per second? (b) At what distance below the bottom of the tank is the cross-sectional area of the stream equal to one-half the area of the hole? (a) Number Units (b) Number Units

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter9: Fluids And Solids

Section: Chapter Questions

Problem 45P: The inside diameters of the larger portions of the horizontal pipe depicted in Figure P9.45 are 2.50...

See similar textbooks

Similar questions

Calculate Reynolds numbers for flow of trough (a) a nozzle a radius of 0.250 cm and (b) a garden hose with a radius of 0.900 cm, when be nozzle is attached to hose. The flow rate through hose and nozzle is 0.500 L/s. Can flow in either possibly be laminar?
What is density of a woman floats in fresh water with 4.00% of her volume above the surface? (This could be measured by placing her in a Wii marks on the side to measure how much water she displaces when floating and when held under water.) (b) What percent of her volume is above surface when she floats in seawater?
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.
A container of water has a cross-sectional area of A=0.1m2 . A piston sits top of the water (see be following figure). There is a spout located 0.15 m from the bottom of tank, open to the atmosphere, and a stream of water exits the spout. The cross sectional area of the spat is As=7.0104m2 . (a) What is the velocity of the water as it leaves the spout? (b) If the opening of the spout is located 1.5 m above the grand, how far from be pout does water hit the floor? Ignore friction and dissipative forces.
Logs sometimes float vertically a lake because one end has become water-logged and denser than the other. What is the average density of a uniform-diameter log that floats with 20.0% of its length above water?
What must be the contact area between a suction cup (completely evacuated) and a ceiling if the cup is to support the weight of an 80.0-kg student?
The inside diameters of the larger portions of the horizontal pipe depicted in Figure P9.45 are 2.50 era. Water flows to the right at a rate of 1.80 104 m3/s. Determine the inside diameter of the constriction. Figure P9.45
Suppose you have a coffee with a circular cross-section and vertical sides (uniform radius). What is its inside radius if it holds 375 g of coffee filled to a depth of 7.50 cm? Assume coffee has the same density as water.
The flow of blood through a 2.00106 m -radius capillary is 3.80109cm3/s . (a) What is the speed of be blood now? (b) Assuming all the blood in the body passes through capillaries, how many of them must there be to carry a total flow of 90.0 cm3/s?
Water emerges straight down from a faucet with a 1.80-cm diameter at a speed of 0.500 m/s. (Because of the construction of the faucet, there is no variation in speed across the stream.) (a) What is flow rate in cm3/s? (b) What is the diameter of the stream 0.200 m below the faucet? Neglect any effects due to surface tension.
A straightforward method of finding the density of an object is to measure its mass and then measure its volume by submerging it in a graduated cylinder. What is the density of a 240-g rock 89.0 cm3 of water? (Note that the accuracy and practical applications of this technique are more limited than a variety of others that are based on Archimedes' principle.)
A trash compactor can compress its contents to 0.350 times their original volume. Neglecting mass of air expelled, by what factor is the density of be rubbish increased?