A DC chopper controls the speed of PMDC motor. The motor has 0.5 arma resistance and 0.05H armature inductance. DC bus voltage is 300V. In a specific condition, when the duty cycle is 0.5, the back EMF of the motor is 140V. chopping frequency is 1kHz. a. Sketch the circuit b. Find the maximum and minimum values of the motor current.

A DC chopper controls the speed of PMDC motor. The motor has 0.5 arma resistance and 0.05H armature inductance. DC bus voltage is 300V. In a specific condition, when the duty cycle is 0.5, the back EMF of the motor is 140V. chopping frequency is 1kHz. a. Sketch the circuit b. Find the maximum and minimum values of the motor current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the AC circuit shown in the image, that is driven by a voltage V=V0cos(ωt). a) What is the current through the capacitor, C? Give its amplitude and phase relative to the drive voltage. b) What is the total current through the voltage source? Again require amplitude and phase relative to the drive voltage.
Q.10/ Design an H-Bridge DC motor driver circuit and explain its principle of operation.
A 2-pole, single-phase alternator driven at 3000rpm require a mechanical input to its rotor of 30kW when it is delivering its full-load output of 30kW. Under this condition the fixed and variable losses are1100W and 2.8kW respectively, and the rotor field winding is supplied from a 110V dc source. Given that the full-load efficiency is 87%, determine. the frequency generated, the input driving torque on full-load and the rotor field current
A shunt generator supplies a 30kW load at 215V through cables of resistance, R = 110mn. If the field winding resistance, Rf =680 and the armature resistance, Ra =45mn. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
A phase control circuit is mainly composed of a TRIAC in series with the load resistance, RL, powered by an AC voltage source (in RMS), VAC. A TRIAC may not fire symmetrically on both half cycles. In this condition, derive the average load voltage. Assume the firing delay angles for positive and negative halves are α+ and α-, respectively.
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
A separately excited motor runs at 1045rpm, with a constant field current, while taking an armature current of 50A at 120V. The armature resistance is 0.1 Ω if the load on the motor changes such that it now takes 95A at 120V, determine the motor speed at this load.
A phase control circuit is mainly composed of a TRIAC in series with the load resistance, RL, powered by an AC voltage source (in RMS), VAC. A TRIAC may not fire symmetrically on both half cycles. In this condition, derive the RMS load voltage. Assume the firing delay angles for positive and negative halves are α+ and α-, respectively.
Pls Explain the following Contrast DC motor types withDC generator
Explain the concept of reactive power compensation and its role in improving power system voltage stability.
Discuss why the THD and frequency regulation is better in the Inverter type generators?
What is the ripple factor and what causes it? Discuss and explain how this factor can be used as a metric to improve the quality of the designed AC to DC converting system