Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque can be reached to 750 rpm. When the supply voltage of converter is 150 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 a and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.

Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque can be reached to 750 rpm. When the supply voltage of converter is 150 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 a and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

Q.10/ Design an H-Bridge DC motor driver circuit and explain its principle of operation.
A four-pole induction motor drives a load at 2405 rpm. This is to be accomplished by using an electronic converter to convert a 400V dc source into a set of three-phase ac voltages. a) Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2hp. b) If the dc-to-ac converter has a power efficiency of 93 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source.
A DC series motor is operated at full load from a 250V supply. The counter emf is found to be 220V at a line current of 40A. Find the armature resistance assuming the series field resistance is 0.3Ω
A brushed DC motor is spinning at a maximum no-load speed of 6206 rpm. The nominal brush voltage drop is 0.67 V and the rated terminal voltage of the machine is 13 V. Determine the voltage constant, Ke, of the machine in Vs/rad.
Suppose a shunt regulator voltage is 250V, the armature current is 30A. field coils are required to provide an MMF of 500AT. The field might typically say 200turns with resistance of 0.5Ohms/turn. Find the dissipated power as heat and total input required and the efficiency
A DC chopper is used in regenerative breaking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continous and ripple free. What is the value of power feedback to the supply ?
A four-pole induction motor drives a load at 2500 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. If the dc-to-ac converter has a power efficiency of 88 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source.
A 4-pole induction motor drives a load at 2500 rpm. This is to be accomplished by using an electronic converter to convert 400 Volts DC into a set of 3-phase AC voltages. Find the frequency required for the AC voltages assuming that the slip is 4 percent. The load requires 2 hp. If the DC-to-AC converter has a power efficiency of 88 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the DC source.
Hi .. This is simulation starting synchronous motor in matlab 2012 who can I find the power factor by use this simulation and what is the elemen add to find the power factor
Q: At differential compound dc motor the speed remaining almost constant when the load increasing .Discusss.
what is the best switch for buck boost converter and why
A separately excited motor runs at 1045rpm, with a constant field current, while taking an armature current of 50A at 120V. The armature resistance is 0.1 Ω if the load on the motor changes such that it now takes 95A at 120V, determine the motor speed at this load.