A DC machine has 2 poles on the stator, the armature winding has 20 coils and 8 turns per coil. The armature radius r 12.5cm, armature length 1 25cm. The poles cover 80% of the armature while the average magnetic flux density per pole is 0.9T. Determine (a) what is total flux per pole (b) For lap-wound and wave-wound machines, what are the armature constants respectively

A DC machine has 2 poles on the stator, the armature winding has 20 coils and 8 turns per coil. The armature radius r 12.5cm, armature length 1 25cm. The poles cover 80% of the armature while the average magnetic flux density per pole is 0.9T. Determine (a) what is total flux per pole (b) For lap-wound and wave-wound machines, what are the armature constants respectively

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The armature of a dc motor has 648 conductors, 65 % of which are directly under the pole where the flux density is 48,000 lines per in2. If the core diameter is 7 inches and its length is 4 inches and the current in each conductor is 20 A. What is the torque exerted in the armature in N-m?
The armature of DC machine has an outer diameter 55cm and effective Length is 25cm, the armature has a wave winding consisting 488 conductors. The number of poles is 6 poles, each pole producing a flux 43mw. Calculate the conductor e.m.f and the total armature e.m.f, when speed is 1000
4 pole direct current electrical machine works as a generator. In this direct current machine, which also has auxiliary poles, the direction of the excitation flux is from the bottom at the remaining pole located at the upper part of the armature. As the current direction in armature conductor corresponding to the same pole is ๏ direction; a. The direction of flux at the main polesb. Current direction at main polesc. Direction of flux at auxiliary polesD. Direction of current at auxiliary polese. Show the direction of rotation by drawing a figure.
The 4-pole direct current electric machine works as a generator. In this direct current machine, which also has auxiliary poles, the direction of the excitation flux is from bottom to top at the remaining pole located at the top of the armature from the main poles on the d axis. As the current direction is ๏ in armature conductors corresponding to the same pole; (show by drawing the figure)a. The direction of flux at the main polesb. Current direction at main polesc. Direction of flux at auxiliary polesD. Direction of current at auxiliary polesto. Direction of rotation
The 4-pole direct current electric machine works as a generator. In this direct current machine, which also has auxiliary poles, the direction of the excitation flux is from bottom to top at the remaining pole located at the top of the armature from the main poles on the d axis. As the current direction is ๏ in armature conductors corresponding to the same pole; (show by drawing the figure)a. The direction of flux at the main polesb. Current direction at main polesc. Direction of flux at auxiliary polesD. Direction of current at auxiliary polese. Direction of rotation
Suppose that we are designing a 1200-rpm dc motor to run from a 240-V source. We have determined that the flux density will be 1 T because smaller fluxes make inefficient use of the iron and larger fluxes result in saturation. The radius of the rotor (and thus, the torque arm for the armature conductors) is 0.1 m. The lengths of the armature conductors are 0.3 m. Approximately how many armature conductors must be placed in series in this machine?
- A separately excited 4 - pole, 900 rpm wave wound dc generator has an induced emf of 240V at rated speed and rated field current. When connected to a load, the terminal voltage is observed to be 200V. If the armature resistance is 0.2 Ω and the flux per pole is 10 m Wb, compute the armature current and the number of conductors
A dc motor has an armature containing 192 conductors, 70 percent of which lie directly under the pole faces at any given instant. If the flux density under the poles is 52,000 lines per square inch and the armature diameter and length are 12 in and 4.5 in., respectively, calculate the current in each armature conductor for a torque of 120 lb-ft.
A 4-pole, simplex lap wound, direct current armature has 48 slots containing 48 coils, each of two turns. The flux per pole, in the field structure for this armature, is 692000 maxwell. Calculate the speed for this machine in order that its generated emf is 220 V.
1.- The production of a force in a conductor carrying current that is inside a magnetic field, is the basis of? 2.- What happens in the flux of a ferromagnetic core of a transformer if the cross section is reduced? : 3.- This force is present internally in the DC motor when the rotor rotates within the magnetic field. 4.- What happens if the field circuit opens in a shunt connected direct current generator?
Using cross -sectional diagrams of a 4 -pole machine, show the flux distributions resulting from (i)the main field acting alone, (ii)the armature field acting alone, and (iii)the main andarmature fields acting together.
What are the two parameters which are considered in piezo actuators? Why contracting actuators are also called bending actuators? Which property of magnetic material and effects are used in magneto-strictive actuators, Explain in detail with suitable application in industrial scenario?